ATT Internet AIr
-
The weirdness still continues
Even though I thought I had things working correctly the dynamic ipv4 gateway would go offline and I couldn't get it to come back on
(admitedly all this might be the provisioning issue)BUT -- I can get the ipv4 gateway to come online by enabling the dynamic ipv6 for the interface
when I enable that - it immediately makes the ipv4 gateway come online!!I know so little about ipv6 --- does any of that sound familiar to anyone?
-
You can't put those two VIPs on different interfaces because they are both using the same subnet.
You will need to change the management IP for one of the modems so it's in a different subnet,
-
Ok. I know there are lots of variables in this messed up case, but I originally had modem #2 setup on 192.168.3.1 and it didn’t work
That’s why I switched
But I guess I shouldn’t have same subnet VIPs on different interfaces?? -
Indeed you can't have the same subnet on more than one interface. Especially because the gateway for one of them is in that subnet. You have a routing conflict which is probably why it stopped responding.
-
@stephenw10 @stephenw10
Well I spoke too soon -- even modem #1 (with the presumed correct ATT provisioning ) finally started disconnecting ...When I watch the modem dashboard screen (and even the ethernet lights) it appears the ethernet connection intermittently disconnectsand reconnects
And YES I was able to get into the modem interface (with appropriate creation of VIP) and set the MAC address to the pfsense interface. And I even "blocked" (on the ATT modem ethernet interface) the MAC address of the switch VLAN port.So my question for you guys -- have I done everything that I can do -- any other VLAN settings to change or try?
And if I have my options are to :- do as @Gblenn suggested and just modify my setup so that my pfsense has only my various LAN subnets connected via VLAN and connect the ATT modem directly to the pfsense
or
- assuming I haven't done something wrong and others on the internet who have connected a WAN through VLAN succesfully -- then return my ATT modem and buy a cellular modem gateway that will work correctly with VLAN (and utilize ATT). If I go that route - any suggestions on device?
I am attaching my VLAN settings one more time to be sure I haven't overlooked something
where VLAN ID 10 was my modem
-
@ahole4sure said in ATT Internet AIr:
even modem #1 (with the presumed correct ATT provisioning ) finally started disconnecting ...
That is wierd, so when it's connected directly to the pfsense interface, it is stable and "just works"? But when connected via the TPLink, it disconnects... and reconnects?
Does it at least maintain the MAC and provide that intermittent connection only towards pfsense now? Anything in the TPLink switch that can give an indication, like stats (bad packets etc)? Does the port light turn off when the link is down?
I'm starting to think it could be a cable issue perhaps?
-
-
Hard to imagine the VLAN itself could be an issue. I would try to remove VLAN 1 from the interface connected to the modem. The switch admin interface is the only thing that could be interacting with the modem. Everything else is just forwarding packets.
I assume the switch interface is set statically? If it's set as dhcp that could be a problem.
-
So I changed all cables
No change
Currently if I connect eitehr ATT modem through port 2 of the switch with port 1 connected to the pfsense igb3 port - I get this cycling over 1 to 10 seconds fo connected (varies between 1 and 2 devices - when 2 devices connected shows on the ATT modem it reports the MAC of the pfsense port and the switch), and disconnected (see photos of the ATT device - those photos are about 5 sec apart)I made changes in the switch to get rid of any members to the default VLAN (VLAN 1).
I ordered 2 new switch from. Amazon - a netgear and a different one to see if it has to do with the switch
-
Port 1 should not have pvid 10. You don't want untagged traffic there ending up at the modem. Though there shouldn't be any untagged traffic arriving at port1.
-
Would there be anything else to explore , that would make the device intermittently connect and disconnect from the Ethernet??
Ordered new switches to trial that
Could it be anything in pfsense that would cause that?
And I guess it could be the ATT modem, but both modem # 1 and 2 do it so it would have to be a widespread issue
-
Hard to imagine it could be the switch.
Just to confirm though the switch admin interface itself is configured using a static IP address?
If that is set to DHCP it could be leaking requests out of VLAN10 causing problems. -
Yes, sorry I meant to send screenshot
It is static -
Hmm, well hard to say what's happening then. Is there any logging in the modem showing what the second client is?
-
I'm pretty sure it's the TPLink switch showing up as the second client...
@stephenw10 said in ATT Internet AIr:
Just to confirm though the switch admin interface itself is configured using a static IP address?
If that is set to DHCP it could be leaking requests out of VLAN10 causing problems.I remember having an issue with a TPLink switch of similar type (TL1016D). It was changing it's management IP over to one of my VLAN's, intermittently. But I'm afraid I can't remember now how I resolved it...
-
THIS has been an ordeal from hell .....
So for sure things have been better with a Linksys Smartswitch - GS105E-200NAS
However, the MAIN issue has been finding out that the second modem of the 2 that I received from ATT was not configured properly - that is one of the reasons that the gateway kept going offline.ATT is working on confiuguring modem #2
With modem #1 I have succesfully gotten the DHCP for the ATT wan to go to the public IP address !The questions -- do my VLAN settings look correct?
Also if I configure the ATT modem as a failover and then fail my fiber modem (by disconnecting it)
My LAN internet (delivered mostly by Eero wireless) was not existent until I created a rule for the ATT modem to beable to access any source and any destination? Is that acceptable?
The network seemed a bit squirrely but I wasn't sure if I needed any other settings like - should I normally be able to get by with "auto-created" Outbound NAT? Or do I need to have my Outbound rules in hybrod mode? They are a MESS currently from pst attempts to "fix" problems!Last question - after I reconnect my fiber modem - it took like 5 mintues or longer for my LAN (and wireless) internet to come back up properly suing my fiber ---- it seemed like it was stuck in some sort of limbo land trying to convert back to fiber from the ATT backup. Wasn't sure how to troubleshoot that - or do you have suggestions?
THANK YOU GUYS AGAIN!!!
-
Sounds like it may have been the modem and not the switch? Once you get it working, I'd change back to the TPLink switch to see if it is also ok, which I suspect it is. I use TPLink Omada switches but have one older switch with the same interface as yours, and it's been really stable. I think the one thing that I had to do was to set it's management IP manually so it wouldn't pick up an IP from one of the VLAN's. I also have that 5-port Netgear switch and I had some problems with it where I had to restart it now and then because the UI didn't work. It was switching traffic and VLAN's worked fine but for some reason the web interface locked up.
@ahole4sure said in ATT Internet AIr:
The questions -- do my VLAN settings look correct?
I think they do, for the most part, except that ID 1 (default) should not be changed from the std setting (untagged). It looks like you changed it to tagged on port 1? The only time you make changes involving ID 1 is when you want to exclude it from one of the ports. Like when you connect your NAS or other servers to a port in order to isolate them from the rest of the networks.
During testing it could be a good idea to keep one of the other ports at default setting so you have an alternative port to access the UI...
Also if I configure the ATT modem as a failover and then fail my fiber modem (by disconnecting it)
My LAN internet (delivered mostly by Eero wireless) was not existent until I created a rule for the ATT modem to beable to access any source and any destination? Is that acceptable?Check your rules on your default LAN, the one at the bottom, that is your default any source to any network rule. Remember, this sits below any other blocking or routing rules, and is Internal to External. You want any devices on your LAN to be able to access the world, and that includes everything. So each VLAN needs to have that rule at the bottom. But in order to really isolate a VLAN from the rest of your networks, you have to add Blocking rules above that. One rule per the other networks that you want to block access to. So on VLAN 10 you will have a Block rule with source Any and destination VLAN 20. Another one with dest VLAN 30 and of course your LAN. On the LAN network you do want to be able to access the VLAN's I suppose, since you want to reach your NAS and whatever servers or devices you have. So typically no blocking access to the VLAN's.
The network seemed a bit squirrely but I wasn't sure if I needed any other settings like - should I normally be able to get by with "auto-created" Outbound NAT? Or do I need to have my Outbound rules in hybrod mode? They are a MESS currently from pst attempts to "fix" problems!
You should be able to keep your outbound rules to Auto, and not mess with hybrid and adding rules manually there.
Last question - after I reconnect my fiber modem - it took like 5 mintues or longer for my LAN (and wireless) internet to come back up properly suing my fiber ---- it seemed like it was stuck in some sort of limbo land trying to convert back to fiber from the ATT backup. Wasn't sure how to troubleshoot that - or do you have suggestions?
When you unplug your fiber, you should notice a short interruption. Like if you are on a Teams call, it will freeze for a few (7-10 seconds) and then get back up again when it has switched over to the failover connection.
When you reattach the fiber you should not notice anything. The default setting (I think) is not to flush states, which means that connections remain on the failover gateway until you close them. So your Teams meeting will continue on the failover gateway until you close the meeting. Only when you start a new meeting, will it end up on the fiber again. You can change this so pfsense will Kill states also at recovery, which means that you will get that short interruption and reconnect when you recover from a failover.The time it takes depends on your settings under Routing where you define the "decision criteria" for switching between gateways. Packet loss or member down for example as well as the threshold numbers.
THANK YOU GUYS AGAIN!!!
-
That looks correct. What firewall rule did you have to add though?
I wouldn't expect any firewall rule to be needed. Nor any outbound NAT rules as long as outbound NAT is still in auto or hybrid mode. The new WAN is DHCP so they will be added automatically.
-
@stephenw10 said in ATT Internet AIr:
I wouldn't expect any firewall rule to be needed.
I'm not sure the any to any rule is actually created automatically when you create a VLAN?
-
The outbound NAT rules are created automatically.
Firewall rules are not but shouldn't be required. Hence I'm curious about exactly what rule had to be added manually.
