After upgrade 24.03 to 24.11 reboot hangs at start @ 0xffffff....
-
@Bogart-ICQa said in After upgrade 24.03 to 24.11 reboot hangs at start @ 0xffffff....:
The upgrade process itself completes but the box is not rebooting into the new version. Its just is stuck with solid light orange, purple, blue.
What does the console show while that is happening?
-
Version 2.22.1285. Copyright (C) 2024 AMI BIOS Date: 02/01/2024 15:18:05 Ver: 2AZRT81 Press <DEL> or <ESC> to enter setup. Consoles: EFI console Reading loader env vars from /efi/freebsd/loader.env Setting currdev to disk0p1: FreeBSD/amd64 EFI loader, Revision 1.1 (Fri Nov 22 05:06:57 UTC 2024 root@freebsd) Command line arguments: loader.efi Image base: 0x54a1f000 EFI version: 2.80 EFI Firmware: American Megatrends (rev 5.26) Console: efi (0x1000) Load Path: \EFI\freebsd\loader.efi Load Device: PciRoot(0x0)/Pci(0x14,0x0)/USB(0x5,0x0)/HD(1,GPT,E3589FC9-9482-11EE-975D-4550A2D939BA,0x3,0x64000) BootCurrent: 0001 BootOrder: 0001[*] 0009 0000 000c 000d 000e 000f 0010 0011 0012 0013 0014 000a BootInfo Path: HD(1,GPT,E3589FC9-9482-11EE-975D-4550A2D939BA,0x3,0x64000)/\EFI\freebsd\loader.efi Ignoring Boot0001: Only one DP found Trying ESP: PciRoot(0x0)/Pci(0x14,0x0)/USB(0x5,0x0)/HD(1,GPT,E3589FC9-9482-11EE-975D-4550A2D939BA,0x3,0x64000) Setting currdev to disk0p1: Trying: PciRoot(0x0)/Pci(0x14,0x0)/USB(0x5,0x0)/HD(2,GPT,E3589FD1-9482-11EE-975D-4550A2D939BA,0x64003,0x197FFFD) Setting currdev to zfs:pfSense/ROOT/default_20250107160359_20250108115934: Loading /boot/defaults/loader.confault: Loading /boot/defaults/loader.conf Loading /boot/device.hints Loading /boot/loader.conf Loading /boot/loader.conf.lua Netgate 4200 detected. Loading /boot/loader.conf.local | - \ __ _ __ / _|___ ___ _ __ ___ ___ _ | '_ \| |_/ __|/ _ \ '_ \/ __|/ _ \ _| |_ | |_) | _\__ \ __/ | | \__ \ __/ |_ _| | .__/|_| |___/\___|_| |_|___/\___| |_| |_| ╔════ Welcome to Netgate pfSense Plus ════╗ __________________________ ║ ║ / ___\ ║ 1. Boot Multi user [Enter] ║ | /` ║ 2. Boot Single user ║ | / :-| ║ 3. Escape to loader prompt ║ | _________ ___/ /_ | ║ 4. Reboot ║ | /` ____ / /__ ___/ | ║ 5. Cons: Serial ║ | / / / / / / | ║ ║ | / /___/ / / / | ║ Options: ║ | / ______/ / / _ | ║ 6. Kernel: default/kernel (1 of 2) ║ |/ / / / _| |_ | ║ 7. Boot Options ║ / /___/ |_ _| | ║ 8. Boot Environments ║ / |_| | ║ ║ /_________________________/ ╚═════════════════════════════════════════╝ | Autoboot in 0 seconds. [Space] to pause Loading kernel... /boot/kernel/kernel text=0x1a4c98 text=0xff3048 text=0x17ed568 data=0x180+0xe80 data=0x24c808+0x3b37f8 0x8+0x1d4108+0x8+0x1e9a19 Loading configured modules... can't find '/boot/entropy' /boot/kernel/zfs.ko size 0x619a40 at 0x37be000 /boot/kernel/opensolaris.ko size 0x1e2a8 at 0x3dd8000 can't find '/etc/hostid' staging 0x3fa00000-0x43f40000 (not copying) tramp 0x43f40000 PT4 0x43f41000 Start @ 0xffffffff803a5000 ... /An there it is stuck. The working 24.03 boots as follows:
Version 2.22.1285. Copyright (C) 2024 AMI BIOS Date: 02/01/2024 15:18:05 Ver: 2AZRT81 Press <DEL> or <ESC> to enter setup. Consoles: EFI console Reading loader env vars from /efi/freebsd/loader.env Setting currdev to disk0p1: FreeBSD/amd64 EFI loader, Revision 1.1 (Fri Nov 22 05:06:57 UTC 2024 root@freebsd) Command line arguments: loader.efi Image base: 0x54a20000 EFI version: 2.80 EFI Firmware: American Megatrends (rev 5.26) Console: efi (0x1000) Load Path: \EFI\freebsd\loader.efi Load Device: PciRoot(0x0)/Pci(0x14,0x0)/USB(0x5,0x0)/HD(1,GPT,E3589FC9-9482-11EE-975D-4550A2D939BA,0x3,0x64000) BootCurrent: 0001 BootOrder: 0001[*] 0009 0000 000c 000d 000e 000f 0010 0011 0012 0013 0014 000a BootInfo Path: HD(1,GPT,E3589FC9-9482-11EE-975D-4550A2D939BA,0x3,0x64000)/\EFI\freebsd\loader.efi Ignoring Boot0001: Only one DP found Trying ESP: PciRoot(0x0)/Pci(0x14,0x0)/USB(0x5,0x0)/HD(1,GPT,E3589FC9-9482-11EE-975D-4550A2D939BA,0x3,0x64000) Setting currdev to disk0p1: Trying: PciRoot(0x0)/Pci(0x14,0x0)/USB(0x5,0x0)/HD(2,GPT,E3589FD1-9482-11EE-975D-4550A2D939BA,0x64003,0x197FFFD) Setting currdev to zfs:pfSense/ROOT/default_20250107160359_20250108115934: Loading /boot/defaults/loader.conf Loading /boot/defaults/loader.conf Loading /boot/device.hints Loading /boot/loader.conf Loading /boot/loader.conf.lua Netgate 4200 detected. Loading /boot/loader.conf.local \ - - __ _ __ / _|___ ___ _ __ ___ ___ _ | '_ \| |_/ __|/ _ \ '_ \/ __|/ _ \ _| |_ | |_) | _\__ \ __/ | | \__ \ __/ |_ _| | .__/|_| |___/\___|_| |_|___/\___| |_| |_| ╔════ Welcome to Netgate pfSense Plus ════╗ __________________________ ║ ║ / ___\ ║ 1. Boot Multi user [Enter] ║ | /` ║ 2. Boot Single user ║ | / :-| ║ 3. Escape to loader prompt ║ | _________ ___/ /_ | ║ 4. Reboot ║ | /` ____ / /__ ___/ | ║ 5. Cons: Serial ║ | / / / / / / | ║ ║ | / /___/ / / / | ║ Options: ║ | / ______/ / / _ | ║ 6. Kernel: default/kernel (1 of 2) ║ |/ / / / _| |_ | ║ 7. Boot Options ║ / /___/ |_ _| | ║ 8. Boot Environments ║ / |_| | ║ ║ /_________________________/ ╚═════════════════════════════════════════╝ \ Autoboot in 0 seconds. [Space] to pause Loading kernel... /boot/kernel/kernel text=0x19eec0 text=0xff4c38 text=0x17e3db4 data=0x180 data=0x22d718+0x3d18e8 0x8+0x1cb0f0+0x8+0x1da290| Loading configured modules... can't find '/etc/hostid' /boot/kernel/opensolaris.ko size 0x1e2f0 at 0x35a6000 /boot/kernel/zfs.ko size 0x5ea9a0 at 0x35c5000 can't find '/boot/entropy' staging 0x3fc00000-0x43f40000 (not copying) tramp 0x43f40000 PT4 0x43f41000 Start @ 0xffffffff8039f000 ... GDB: no debug ports present KDB: debugger backends: ddb KDB: current backend: ddb ---<<BOOT>>--- Copyright (c) 1992-2024 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 15.0-CURRENT #0 plus-RELENG_24_03-n256311-e71f834dd81: Fri Apr 19 00:28:14 UTC 2024 root@freebsd:/var/jenkins/workspace/pfSense-Plus-snapshots-24_03-main/obj/amd64/Y4MAEJ2R/var/jenkins/workspace/pfSense-Plus-snapshots-24_03-main/sources/FreeBSD-src-plus-RELENG_24_03/amd64.amd64/sys/pfSense amd64 FreeBSD clang version 17.0.6 (https://github.com/llvm/llvm-project.git llvmorg-17.0.6-0-g6009708b4367) VT(vga): resolution 640x480 CPU: Genuine Intel(R) Atom C1110 processor (2112.00-MHz K8-class CPU) Origin="GenuineIntel" Id=0x906a4 Family=0x6 Model=0x9a Stepping=4 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0x7ffafbbf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,SDBG,FMA,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,TSCDLT,AESNI,XSAVE,OSXSAVE,AVX,F16C,RDRAND> AMD Features=0x2c100800<SYSCALL,NX,Page1GB,RDTSCP,LM> AMD Features2=0x121<LAHF,ABM,Prefetch> Structured Extended Features=0x239ca7eb<FSGSBASE,TSCADJ,BMI1,AVX2,FDPEXC,SMEP,BMI2,ERMS,INVPCID,NFPUSG,PQE,RDSEED,ADX,SMAP,CLFLUSHOPT,CLWB,PROCTRACE,SHA> Structured Extended Features2=0x984007bc<UMIP,PKU,OSPKE,WAITPKG,GFNI,VAES,VPCLMULQDQ,RDPID,MOVDIRI,MOVDIR64B> Structured Extended Features3=0xfc184410<FSRM,MD_CLEAR,IBT,IBPB,STIBP,L1DFL,ARCH_CAP,CORE_CAP,SSBD> XSAVE Features=0xf<XSAVEOPT,XSAVEC,XINUSE,XSAVES> IA32_ARCH_CAPS=0x188fd6b<RDCL_NO,IBRS_ALL,SKIP_L1DFL_VME,MDS_NO,TAA_NO> VT-x: PAT,HLT,MTF,PAUSE,EPT,UG,VPID,VID,PostIntr TSC: P-state invariant, performance statistics real memory = 4294967296 (4096 MB) avail memory = 3887665152 (3707 MB) Event timer "LAPIC" quality 600 ACPI APIC Table: <ALASKA A M I > WARNING: L3 data cache covers more APIC IDs than a package (7 > 3) FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs FreeBSD/SMP: 1 package(s) x 4 core(s) random: registering fast source Intel Secure Key RNG random: fast provider: "Intel Secure Key RNG" random: unblocking device. ioapic0 <Version 2.0> irqs 0-119 Launching APs: 1 3 2 TCP_ratelimit: Is now initialized ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE. ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff80750310, 0) error 1 ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE. ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff807503c0, 0) error 1 ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw.LICENSE. ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff80750470, 0) error 1 iwi_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE. iwi_bss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (iwi_bss_fw, 0xffffffff80770010, 0) error 1 iwi_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE. iwi_ibss: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (iwi_ibss_fw, 0xffffffff807700c0, 0) error 1 iwi_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_iwi.LICENSE. iwi_monitor: If you agree with the license, set legal.intel_iwi.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (iwi_monitor_fw, 0xffffffff80770170, 0) error 1 random: entropy device external interface wlan: mac acl policy registered kbd0 at kbdmux0 WARNING: Device "spkr" is Giant locked and may be deleted before FreeBSD 15.0. efirtc0: <EFI Realtime Clock> efirtc0: registered as a time-of-day clock, resolution 1.000000s netgate0: <Netgate 4200> vtvga0: <VT VGA driver> smbios0: <System Management BIOS> at iomem 0x61c66000-0x61c66017 smbios0: Version: 3.5 acpi0: <ALASKA A M I > acpi_ec1: <Embedded Controller: GPE 0x6e, ECDT> port 0x62,0x66 on acpi0 acpi0: Power Button (fixed) hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 Timecounter "HPET" frequency 19200000 Hz quality 950 Event timer "HPET" frequency 19200000 Hz quality 550 Event timer "HPET1" frequency 19200000 Hz quality 440 Event timer "HPET2" frequency 19200000 Hz quality 440 Event timer "HPET3" frequency 19200000 Hz quality 440 Event timer "HPET4" frequency 19200000 Hz quality 440 atrtc1: <AT realtime clock> on acpi0 atrtc1: Warning: Couldn't map I/O. atrtc1: registered as a time-of-day clock, resolution 1.000000s Event timer "RTC" frequency 32768 Hz quality 0 attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0 Timecounter "i8254" frequency 1193182 Hz quality 0 Event timer "i8254" frequency 1193182 Hz quality 100 Timecounter "ACPI-fast" frequency 3579545 Hz quality 900 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1808-0x180b on acpi0 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 pci0: <ACPI PCI bus> on pcib0 xhci0: <Intel Alder Lake-P Thunderbolt 4 USB controller> mem 0x4000040000-0x400004ffff at device 13.0 on pci0 xhci0: 32 bytes context size, 64-bit DMA usbus0 on xhci0 usbus0: 5.0Gbps Super Speed USB v3.0 pci0: <simple comms, UART> at device 18.0 (no driver attached) pci0: <mass storage> at device 18.7 (no driver attached) xhci1: <Intel Alder Lake USB 3.2 controller> mem 0x4000020000-0x400002ffff at device 20.0 on pci0 xhci1: 32 bytes context size, 64-bit DMA usbus1 on xhci1 usbus1: 5.0Gbps Super Speed USB v3.0 pci0: <memory, RAM> at device 20.2 (no driver attached) pci0: <serial bus> at device 21.0 (no driver attached) pci0: <serial bus> at device 21.1 (no driver attached) pci0: <simple comms> at device 22.0 (no driver attached) pci0: <serial bus> at device 25.0 (no driver attached) pci0: <serial bus> at device 25.1 (no driver attached) pcib1: <ACPI PCI-PCI bridge> at device 28.0 on pci0 pci1: <ACPI PCI bus> on pcib1 pcib2: <ACPI PCI-PCI bridge> at device 28.4 on pci0 pci2: <ACPI PCI bus> on pcib2 igc0: <Intel(R) Ethernet Controller I226-V> mem 0x67a00000-0x67afffff,0x67b00000-0x67b03fff at device 0.0 on pci2 igc0: Using 1024 TX descriptors and 1024 RX descriptors igc0: Using 1 RX queues 1 TX queues igc0: Using MSI-X interrupts with 2 vectors igc0: Ethernet address: 90:ec:77:8e:56:21 igc0: netmap queues/slots: TX 1/1024, RX 1/1024 pcib3: <ACPI PCI-PCI bridge> at device 28.5 on pci0 pci3: <ACPI PCI bus> on pcib3 igc1: <Intel(R) Ethernet Controller I226-V> mem 0x67700000-0x677fffff,0x67800000-0x67803fff at device 0.0 on pci3 igc1: Using 1024 TX descriptors and 1024 RX descriptors igc1: Using 1 RX queues 1 TX queues igc1: Using MSI-X interrupts with 2 vectors igc1: Ethernet address: 90:ec:77:8e:56:20 igc1: netmap queues/slots: TX 1/1024, RX 1/1024 pcib4: <ACPI PCI-PCI bridge> at device 28.6 on pci0 pci4: <ACPI PCI bus> on pcib4 igc2: <Intel(R) Ethernet Controller I226-V> mem 0x67400000-0x674fffff,0x67500000-0x67503fff at device 0.0 on pci4 igc2: Using 1024 TX descriptors and 1024 RX descriptors igc2: Using 1 RX queues 1 TX queues igc2: Using MSI-X interrupts with 2 vectors igc2: Ethernet address: 90:ec:77:8e:56:1f igc2: netmap queues/slots: TX 1/1024, RX 1/1024 pcib5: <ACPI PCI-PCI bridge> at device 28.7 on pci0 pci5: <ACPI PCI bus> on pcib5 igc3: <Intel(R) Ethernet Controller I226-V> mem 0x67100000-0x671fffff,0x67200000-0x67203fff at device 0.0 on pci5 igc3: Using 1024 TX descriptors and 1024 RX descriptors igc3: Using 1 RX queues 1 TX queues igc3: Using MSI-X interrupts with 2 vectors igc3: Ethernet address: 90:ec:77:8e:56:1e igc3: netmap queues/slots: TX 1/1024, RX 1/1024 isab0: <PCI-ISA bridge> at device 31.0 on pci0 isa0: <ISA bus> on isab0 pci0: <serial bus> at device 31.5 (no driver attached) acpi_acad0: <AC Adapter> on acpi0 ns8250: UART FCR is brokene> iomem 0xfe03e000-0xfe03e007 irq 16 on acpi0 uart2: console (115200,n,8,1) acpi_button0: <Sleep Button> on acpi0 cpu0: <ACPI CPU> on acpi0 acpi_tz0: <Thermal Zone> on acpi0 acpi_42000: <Netgate 4200 LED controller SILC1001> on acpi0 atrtc0: <AT realtime clock> at port 0x70 irq 8 on isa0 atrtc0: Warning: Couldn't map I/O. atrtc0: registered as a time-of-day clock, resolution 1.000000s atrtc0: Can't map interrupt. hwpstate_intel0: <Intel Speed Shift> on cpu0 hwpstate_intel1: <Intel Speed Shift> on cpu1 hwpstate_intel2: <Intel Speed Shift> on cpu2 hwpstate_intel3: <Intel Speed Shift> on cpu3 Timecounter "TSC" frequency 2112003010 Hz quality 1000 Timecounters tick every 1.000 msec ugen0.1: <Intel XHCI root HUB> at usbus0 ZFS filesystem version: 5 ZFS storage pool version: features support (5000) uhub0 on usbus0 uhub0: <Intel XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0 ugen1.1: <Intel XHCI root HUB> at usbus1 Trying to mount root from zfs:pfSense/ROOT/default_20250107160359_20250108115934 []... uhub1 on usbus1 uhub1: <Intel XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus1 uhub0: 3 ports with 3 removable, self powered uhub1: 16 ports with 16 removable, self powered Root mount waiting for: usbus1 CAM Root mount waiting for: usbus1 CAM ugen1.2: <Generic Ultra Fast Media> at usbus1 umass0 on uhub1 umass0: <Generic Ultra Fast Media, class 0/0, rev 2.00/1.98, addr 1> on usbus1 Root mount waiting for: CAM Root mount waiting for: CAM Root mount waiting for: CAM Root mount waiting for: CAM Root mount waiting for: CAM Root mount waiting for: CAM Root mount waiting for: CAM da0 at umass-sim0 bus 0 scbus0 target 0 lun 0 da0: <Generic Ultra HS-COMBO 1.98> Removable Direct Access SCSI device da0: Serial Number 000000225001 da0: 40.000MB/s transfers da0: 14952MB (30621696 512 byte sectors) da0: quirks=0x2<NO_6_BYTE> Configuring crash dumps... No suitable dump device was found. Filesystems are clean, continuing... Mounting filesystems... Mounting ZFS boot environment...done. __ _ __ / _|___ ___ _ __ ___ ___ _ | '_ \| |_/ __|/ _ \ '_ \/ __|/ _ \ _| |_ | |_) | _\__ \ __/ | | \__ \ __/ |_ _| | .__/|_| |___/\___|_| |_|___/\___| |_| |_| Welcome to Netgate pfSense Plus 24.03-RELEASE (Patch 1)... ...ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/local/lib/compat/pkg /usr/local/lib/compat/pkg /usr/local/lib/graphviz /usr/local/lib/ipsec /usr/local/lib/mysql /usr/local/lib/perl5/5.36/mach/CORE 32-bit compatibility ldconfig path: done. 3379 >>> Removing vital flag from php83...done. External config loader 1.0 is now starting... da0p1 da0p2 da0p3 Launching the init system...Updating CPU Microcode... CPU: Genuine Intel(R) Atom C1110 processor (2112.00-MHz K8-class CPU) Origin="GenuineIntel" Id=0x906a4 Family=0x6 Model=0x9a Stepping=4 Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE> Features2=0x7ffafbbf<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,SDBG,FMA,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,TSCDLT,AESNI,XSAVE,OSXSAVE,AVX,F16C,RDRAND> AMD Features=0x2c100800<SYSCALL,NX,Page1GB,RDTSCP,LM> AMD Features2=0x121<LAHF,ABM,Prefetch> Structured Extended Features=0x239ca7eb<FSGSBASE,TSCADJ,BMI1,AVX2,FDPEXC,SMEP,BMI2,ERMS,INVPCID,NFPUSG,PQE,RDSEED,ADX,SMAP,CLFLUSHOPT,CLWB,PROCTRACE,SHA> Structured Extended Features2=0x984007bc<UMIP,PKU,OSPKE,WAITPKG,GFNI,VAES,VPCLMULQDQ,RDPID,MOVDIRI,MOVDIR64B> Structured Extended Features3=0xfc184410<FSRM,MD_CLEAR,IBT,IBPB,STIBP,L1DFL,ARCH_CAP,CORE_CAP,SSBD> XSAVE Features=0xf<XSAVEOPT,XSAVEC,XINUSE,XSAVES> IA32_ARCH_CAPS=0x188fd6b<RDCL_NO,IBRS_ALL,SKIP_L1DFL_VME,MDS_NO,TAA_NO> VT-x: PAT,HLT,MTF,PAUSE,EPT,UG,VPID,VID,PostIntr TSC: P-state invariant, performance statistics Done. done. Initializing.................... done. Starting device manager (devd)...ig4iic0: <Intel Alder Lake-P I2C Controller-0> at device 21.0 on pci0 ig4iic0: Using MSI iicbus0: <Philips I2C bus (ACPI-hinted)> on ig4iic0 iicbus0: <unknown card> at addr 0x14 ig4iic1: <Intel Alder Lake-P I2C Controller-1> at device 21.1 on pci0 ig4iic1: Using MSI iicbus1: <Philips I2C bus (ACPI-hinted)> on ig4iic1 ig4iic2: <Intel Alder Lake-P I2C Controller-4> at device 25.0 on pci0 ig4iic2: Using MSI iicbus2: <Philips I2C bus (ACPI-hinted)> on ig4iic2 ig4iic3: <Intel Alder Lake-P I2C Controller-5> at device 25.1 on pci0 ig4iic3: Using MSI iicbus3: <Philips I2C bus (ACPI-hinted)> on ig4iic3 driver bug: Unable to set devclass (class: uart devname: (unknown)) driver bug: Unable to set devclass (class: atkbdc devname: (unknown)) ichsmb0: <Intel Alder Lake SMBus controller> port 0xefa0-0xefbf mem 0x4000064000-0x40000640ff at device 31.4 on pci0 smbus0: <System Management Bus> on ichsmb0 done. Loading configuration....done. Updating configuration...done. Loading cryptographic accelerator drivers...aesni0: <AES-CBC,AES-CCM,AES-GCM,AES-ICM,AES-XTS,SHA1,SHA256> done. Setting up extended sysctls...done. Executing early shell commands...WireGuard service is disabled done. coretemp0: <CPU On-Die Thermal Sensors> on cpu0 Setting timezone...done. Configuring looplo0: link state changed to UP back interface...done. Starting syslog...done. Setting up interfaces microcode...done. Configuring loopback interface...done. Configuring WAN interface...done. Configuring LAN interface...done. Configuring DMZ interface...done. Configuring CARP settings...done. Starting Secure Shell Services...done. Syncing OpenVPN settings...done. [fib_algo] inet.0 (bsearch4#22) rebuild_fd_flm: switching algo to radix4_lockless route: route has not been found route: route has not been found Configuring firewall..load_dn_sched dn_sched FIFO loaded load_dn_sched dn_sched QFQ loaded load_dn_sched dn_sched RR loaded load_dn_sched dn_sched WF2Q+ loaded load_dn_sched dn_sched PRIO loaded load_dn_sched dn_sched FQ_CODEL loaded load_dn_sched dn_sched FQ_PIE loaded load_dn_aqm dn_aqm CODEL loaded load_dn_aqm dn_aqm PIE loaded ....done. Starting PFLOG...done. Setting up gateway monitors...done. Setting up static routes...done. Setting up DNSs... Starting DNS Resolver...done. Synchronizing user settings...done. Configuring CRON...done. Bootstrapping clock...done. Starting NTP Server...done. Starting webConfigurator...config_aqm Unable to configure flowset, flowset busy! config_aqm Unable to configure flowset, flowset busy! done. Configuring firewall..config_aqm Unable to configure flowset, flowset busy! config_aqm Unable to configure flowset, flowset busy! ....done. Generating RRD graphs...done. Starting syslog...config_aqm Unable to configure flowset, flowset busy! done. Starting CRON... done. Starting package AWS VPC Wizard...done. Starting package IPsec Profile Wizard...done. Starting package Netgate Firmware Upgrade...done. Starting package WireGuard...done. Starting package pfBlockerNG...done. Starting package Traffic Totals...done. Starting package Tailscale...done. Starting package OpenVPN Client Export Utility...done. Starting package haproxy...done. Starting package acme...done. Starting package nrpe...done. Starting package ntopng...done. Starting package arpwatch...done. Starting /usr/local/etc/rc.d/pfb_dnsbl.sh...done. Starting /usr/local/etc/rc.d/pfb_filter.sh...done. Starting /usr/local/etc/rc.d/vnstatd.sh...done. Netgate pfSense Plus 24.03-RELEASE (Patch 1) amd64 20240424-1738 Bootup complete Performing automatic boot verification...done. FreeBSD/amd64 (pfSense.ccdrdag.com) (ttyu2) Netgate 4200 - Serial: 2006240239 - Netgate Device ID: 053c5c7683fe73b0f27e *** Welcome to Netgate pfSense Plus 24.03-RELEASE (amd64) on pfSense *** Current Boot Environment: default_20250107160359_20250108115934 Next Boot Environment: default_20250107160359_20250108115934 WAN (wan) -> igc3 -> v4: 10.199.100.10/24 LAN (lan) -> igc2 -> v4: 192.168.201.1/24 DMZ (opt1) -> igc1 -> v4: 10.10.100.1/24 0) Logout (SSH only) 9) pfTop 1) Assign Interfaces 10) Filter Logs 2) Set interface(s) IP address 11) Restart GUI 3) Reset admin account and password 12) PHP shell + Netgate pfSense Plus tools 4) Reset to factory defaults 13) Update from console 5) Reboot system 14) Disable Secure Shell (sshd) 6) Halt system 15) Restore recent configuration 7) Ping host 16) Restart PHP-FPM 8) Shell Enter an option: -
And that is just booting the two BEs? No other changes?
-
Yes.
-
I got it booting into 24.11 using the console upgrade option (lucky number 13).
Had to reboot twice though. After the first reboot the GUI wasn't working (bad request error).
Now it seems to be ok (fingers crossed). -
Hmm, so upgrading via the gui resulted in no boot but upgrading via the CLI succeeded?
There should be no difference between those.
-
@stephenw10 said in After upgrade 24.03 to 24.11 reboot hangs at start @ 0xffffff....:
Hmm, so upgrading via the gui resulted in no boot but upgrading via the CLI succeeded?
There should be no difference between those.
Others upthread had success when they tried it again, so it may have been the retry that did it and not the method. Still doesn't make a lot of sense, but at least seems to be consistently inconsistent.
-
@jimp with the GUI i tried twice with the same outcome. First from home which had me to turn into the office at night to fix it.
-
Successfully upgraded from 24.03 to 24.11 via command line (SSH).
I'd been dreading the unpleasant task of dealing with the previous GUI update failures, but SSH -> Option 13 -> Reboot and back up in ~3min with little trouble.
-
I encountered this exact same problem on a Netgate 4200 (non-MAX).
Tried upgrading from 24.03 to 24.11 in GUI, the update process seems to go smoothly, untill the reboot. After reboot the device does not come back up. So i rushed to the location in the middle of the night, and encountered the Netgate unit unreachable locally, and all 3 lights on the netgate device are lit up (green / purple / blue). Gave the device a hard reset by pulling power, after which it reverts to 24.03, and operated normally again.
I have then tried the update again, with the same exact results. And again, after pulling power, it reverts to 24.03 and continues operation.The only solution that worked was the one offered by @GripePotato , to SSH into the unit and pick lucky number 13 to upgrade the system. The install on the console looks exactly the same as it did in the web GUI, except after rebooting this time the unit did come back up normally and is running the new version 24.11.
I had postponed the update specifically to wait out any possible bugs. For this bug to still exist months after the update's release, without any warning within the web GUI that is fairly egregious if you ask me. Since it completely kills the unit and someone will have to be on site to pull and restore power from the unit. It would be nice if the unit would recognize the failed update and rebooted itself back into the last working system version, as it does when someone pulls power. It also does not help there is no logging that remains after reverting to 24.03, the update log will simply show there is a 24.11 update available. So the cause of the update breaking remains unknown.
For future updates i guess we will have to have someone on site for every netgate firewall after-hours, and only upgrade the netgate units using the SSH console, to ensure netgate does not break anything with the update again like this.
-
I As far as I know we never managed to replicate this. I upgraded 4200s many, many times during testing. And since then thousands have been upgraded in the field.
I still have no idea what could cause this. Upgrading at the console is the same process at the backend.
Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.