-
@bruor
It might work as it appears to be going through the normal boot from bootable devices. That is where I noticed that, removing the mSata and just installing a working Sata with an "full" install of pfSense. It works fine via Sata drive. I just took the xtra step of seeing if I could get it to start boot on Sata then quickly install the mSata card and allow it to be detected. As you all may know, after the bios boot picks up bootable devices, which is only a sata card, then the pfSense OS starts it does a detection again so this trick will work. I have done it tons of time and never (knock on virgin wood) messed up a mSata card or shorted out and mSata. Speaking of messing up stuff, Be xtra careful if plugging in sata power in the connector. I plugged it in backwards once and thought I blew the whole thing but, it survived and is still working and pfSense it protecting my network. -
@stephenw10 You are exactly right and I am doing everything wrong so anyone trying this it is best to stick a working copy on mSata, using another PC via mSata to Sata adapter. After full install, return it back to the Firebox T70. I really want to hack the bios and install a known password so I can get into the bios and change the boot order. I would like to know what device was used by the bios modder to read the bios. I see two and there is supposed to be another a he mentioned. Is that device plugged in via USB or directly connected to BIOS chip?
-
Usually they are connected via the SPI header. I have not tried that on the T70.
It's much more convenient if you can boot something and read out the chip but I was never able to boot anything with a serial console. The HDMI header is unpopulated so...stuck at that point. It might be possible though.
Steve
-
@stephenw10
I have procured a T70 and if you or someone needs the original mSata for this....it can be sent for you to "look at".
Steven please contact me via Email and we can discuss via phone or emails.
I owe a lot to the group as you all moved me off of Zyxel stuff and onto "roll your own with pfSense". -
Thanks. I've already got one though. Someone else might.
I'm not sure there's much on it we can use. What there is there is detailed in this thread, mostly here.
It would be nice to know where the LEDs are connected. I could never find them in the usual places.Steve
-
Thanks for this information. Unfortunately, it looks like the 1Gb of ram is a serious limitation. I managed to blow it after I installed Squid. All said, it is still a good platform for a peek at Pfsense.
-
The T70 should have 2GB of RAM.
-
@stephenw10 You are absolutely correct. I missed by one key.
-
Just wanted to add some additional information here.
I just did a reinstall on this box to take it to CE 2.7 from plus. During the installation I chose GPT (bios) as the partition type and can confirm that it boots without issue. I think my first install may have been MBR mode.
-
Would like to flash an T35 (looks similar to the T70) to pfSense, but the onBoard UART seems disabled. Tried 2 different USB-Serial-Adapter with Putty and Tera Term. Does somebody knows the correct wiring between Serial-Port and the RJ45-Console-Connector |0|0| instead? Thanks in advance!
-
The T35 uses a PowerPC CPU not X86. So pfSense cannot boot on it.
But I'd expect to see the WGOS boot messages at the RJ-45 serial console at least.
-
@stephenw10 Thank you very much! Didn't knew that this one is PowerPC based. Recovered the WGOS, but still no output via UART. This unit can rest in peace. :)
-
You might be able to get OpenWRT to run on there if you can get access. You should see something on the console though. I'd make sure your terminal setup is good, RJ-45 serial lead is correct etc.
Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.