Need some testers for 0.93 before I release it
-
Scott,
Am I blind or is the image not there anymore to test?
Mike
-
Scott,
Am I blind or is the image not there anymore to test?
Mike
Getting ready to update it. We switched back to FreeBSD 5's dhclient.
-
Noting a glitch dropping the connection. wrap install
-
This is intended behavior. We don't support building a ruleset from scratch atm. That's why we start the shaper wizard to get you a set of rules to start with if there are no rules. You then can modify/add rules after you have the basic construct in place.
Yeh that's my point. I have already run the wizard and I have my set of rules. I used to be able to enable and disable those preset rules without having to re-run the wizard. Now if you untick the enable tick it makes you run the wizard again. Surely this is not as intended.
-
This is intended behavior. We don't support building a ruleset from scratch atm. That's why we start the shaper wizard to get you a set of rules to start with if there are no rules. You then can modify/add rules after you have the basic construct in place.
Yeh that's my point. I have already run the wizard and I have my set of rules. I used to be able to enable and disable those preset rules without having to re-run the wizard. Now if you untick the enable tick it makes you run the wizard again. Surely this is not as intended.
Right, not intended, it should only be running the wizard if there isn't a shaper config at all, not if it's disabled. Please file a ticket for this on cvstrac. Thanks
–Bill
-
Ok ill try :)
-
I installed 0.93 from the livecd. I still get a pretty long wait at the 'Configuring OPT interfaces' (about 3 minutes) on boot up, but then after that everything seems fine so far.
-
I installed 0.93 from the livecd. I still get a pretty long wait at the 'Configuring OPT interfaces' (about 3 minutes) on boot up, but then after that everything seems fine so far.
dhclient on opt?
-
nope, all are static and I entered the interface IP's manually. I do have 5 OPT interfaces though, but 3 are down.
-
PPPoE on the WAN side wasn't working after a full-upgrade installation of 0.93.2. I upgraded from 0.90a from 0.93.2 (I've had DNS & DHCP problems with 0.92) and found that I had no external connection. The WAN interface reported being down after the installation and a subsequent resboot - no IP address, subnet mask, gateway. Nothing. I didn't test much further than this, but DHCP and local DNS services appeared to be working, as did the filters. I didn't experience any delays configuring three OPT interfaces, but there was a 20 second delay configuring the WAN, but this happens with 0.90a as well. I re-load 0.90a (same config settings) and the WAN started working correctly again.
I would be glad to re-install 0.93.2 and provide more detailed info if it would help. (FWIW, The box is a Dell GX150 (1ghz, 256mb if memory serves), WAN is connected to the onboard NIC and the LAN/OPT1/OPT2/OPT3 are on two dual-port Broadcom extreme gig-e cards.)
-
After I upgraded to 0.93.2 I got some issues with dhcp client, after doing some tests the problem was due the NIC, replacing the WAN Nic to other vendor not 3COM, the problem was solved.
I have to add that I'm running my 0.93.2 version since sunday with no problems, and the performance was really improved, I used to have a 60-80% CPU utilization with previous versions, but now it runs smoothly at 5-10% !!!
I'm running TrafficShapping, NTop, and squid on the box, and everything is working superb…
Congratulations again to the pfsense crew, outstanding job!!!
Emanuel Gonzalez
Guatemala