In/Out errors :(

hoba

Maybe we should hardcode these settings for pfSense 1.0. This way it will work for people regardless if they have 1 antenna or 2 (one of them then would simply not be used though present unless you change the sysctl's). Like written in my earlier post the next pfSense version should have settings for these values at the webgui. Updating the wiki won't hurt. I'll do that later (unless lsf does this before I find the time ;) ).

nima.m

Right now I am using BETA3-PLUS-11548-PLUS-11567

I changed /cf/conf/config.xml from :

To :
<afterfilterchangeshellcmd>sysctl dev.ath.0.rxantenna=1;sysctl dev.ath.0.txantenna=1;sysctl dev.ath.0.diversity=0</afterfilterchangeshellcmd>

and save the file.

But when I changed some configuration in WebGui for my WLAN, the <afterfilterchangeshellcmd>inside config.xml had been removed automaticly.</afterfilterchangeshellcmd>

nima.m

Hoba,

I did some more testing and now I fiugre out what should be done.
Whenever, you change the /cf/conf/config.xml file, you need to reboot the router immediately once .

So this is how I make it work :

1.Search /cf/conf/config.xml for

Replace it with :
<afterfilterchangeshellcmd>sysctl dev.ath.0.rxantenna=1;sysctl dev.ath.0.txantenna=1;sysctl dev.ath.0.diversity=0</afterfilterchangeshellcmd>

2.Reboot

3.Now, Whenever you change config for interfaces inside WebGUI, you don't loose the wirless parameters.

sullrich

You have to remove /tmp/rules.debug as well after changing config.xml as its the cached version and will simply overwrite config.xml on the next filter reload operation.

So technically the reboot is not needed.

billm

@sullrich:

You have to remove /tmp/rules.debug as well after changing config.xml as its the cached version and will simply overwrite config.xml on the next filter reload operation.

So technically the reboot is not needed.

close… /tmp/config.cache :)

--Bill

sullrich

@billm:

@sullrich:

You have to remove /tmp/rules.debug as well after changing config.xml as its the cached version and will simply overwrite config.xml on the next filter reload operation.

So technically the reboot is not needed.

close… /tmp/config.cache :)

--Bill

Grr. Bill is absolutely right. This head cold is driving me ape shit.

pcatiprodotnet

My Tx was set to 0, and Rx to 1 (on Atheros).
Is 0 or 1 the First antenna? And, what does it mean when set to "2".
Thank you,
-Pete

hoba

The second time I link to http://forum.pfsense.org/index.php?topic=1149.msg6765#msg6765 in this thread :P

pcatiprodotnet

Thanks hoba!
Although it's fairly obvious, I was just hoping to see it spelled out in no uncertain terms that 0=Main and 1=Aux.
I was careful to read the card's docs to be sure I put the First pigtail (labeled "Antenna#1") on Main,
and the Second pigtail (labeled "Antenna#2") on Aux. -Pete

nima.m

2 means Auto.

What I did was to set both antenna to 0 fisrt and check the in/out errror, then set both to 1 and check the errors again.
Do the same and see when you get less error, then you know which antenna port you should use.

pcatiprodotnet

nima.m, is it possible that you plugged your single pigtail into the card's Aux antenna port, and that is why you had to set it to 1?

hoba

@pcatiprodotnet:

Thanks hoba!
Although it's fairly obvious, I was just hoping to see it spelled out in no uncertain terms that 0=Main and 1=Aux. -Pete

I think that is related to the hardwarelayout. I have even seen cards with no label on either of the antennaoutputs. I recommend doing what nima.m suggested. Try to see what gives you the best results. Generate some traffic (try to load it) and you should see errors increasing rather fast with the wrong setting. Closing the case might help finding the wrong setting too, so you get some noise reflections inside the case with the non hooked up output.

nima.m

I have no idea :-)

I bought one of those Lintex 6 Nic router and told them to install a CM9 minipci and a external antenna and send it to me.
And they did that, And I havn't open my case for checking it.

pcatiprodotnet

I just tried the above procedure on beta4, deleted /tmp/config.cache, rebooted for good measure, and it didn't change.
I loaded up /cf/conf/config.xml , and re-checked it…
<maximumstates><afterfilterchangeshellcmd>sysctl dev.ath.0.rxantenna=0;sysctl dev.ath.0.txantenna=0;sysctl dev.ath.0.diversity=0</afterfilterchangeshellcmd>

but in shell it still reports...

sysctl dev.ath.0.diversity

dev.ath.0.diversity: 1

sysctl dev.ath.0.rxantenna

dev.ath.0.rxantenna: 1

sysctl dev.ath.0.txantenna

dev.ath.0.txantenna: 0</maximumstates>

nima.m

Change it to :

<shellcmd>sysctl dev.ath.0.rxantenna=1;sysctl dev.ath.0.txantenna=1;sysctl dev.ath.0.diversity=0</shellcmd>
<afterfilterchangeshellcmd>sysctl dev.ath.0.rxantenna=1;sysctl dev.ath.0.txantenna=1;sysctl dev.ath.0.diversity=0</afterfilterchangeshellcmd>

then reboot and check

sysctl dev.ath.0.diversity

pcatiprodotnet

It's still unchanged. -Pete

pcatiprodotnet

Is there a way to simply run a shell script after pfsense finishes booting? If so, I could put the sysctl commands there.
This problem with the antennas is causing us quite a bit of hassle.
Also, I wouldn't recommend pfSense pre-determining the antenna settings because people will often attach a single pigtail on the "wrong" mini-pci U.FL connector or transpose two connectors for main/aux. If you must, perhaps setting both Tx & Rx to Auto would be the most generally helpful; but, having the ability to set them in the GUI is golden.
Thank you, -Pete

lsf

This is not something we controll, it's controlled by the freebsd driver/HAL. One of the reasons i haven't added these settings are just because of that. What should be defaults ? should I first up the card and enable it, and then allow the values to be changed ? if not, how should i get the defaults ? (the defaults "change" based on what settings it found "sensible" when the interface was up'ed and configured).
Basically what i'm trying to say is that the driver does not behave the same on every HW combo/user setup. So it's hard to pick any default. I know the driver does not do this perfectly, but it probably does a better job then us presetting/hardcoding this.

nima.m

@pcatiprodotnet:

Is there a way to simply run a shell script after pfsense finishes booting? If so, I could put the sysctl commands there.

Thats what shellcmd tag do,

Lets try this
1.Change your config file in this way :
<shellcmd>echo 1 > /beforeShell;sysctl dev.ath.0.rxantenna=1;sysctl dev.ath.0.txantenna=1;sysctl dev.ath.0.diversity=0;echo 1 > /afterShell</shellcmd>
<afterfilterchangeshellcmd>echo 1 > /beforeFilter;sysctl dev.ath.0.rxantenna=1;sysctl dev.ath.0.txantenna=1;sysctl dev.ath.0.diversity=0;echo 1 > /afterFilter;</afterfilterchangeshellcmd>

2.Reboot

3.SSH to your router

4.Run this command one by one and see the result :

ls /beforeShell
ls /afterShell
ls /beforeFilter
ls /afterFilter

pcatiprodotnet

After some investigation, I discovered that boot commands are working; however, after a little time, the old settings get put back. I'm not quite sure what to make of this. Perhaps with Diversity is On, the wireless card is changing the Rx antenna setting based on what it thinks is best at the moment?

Another handy command: athstats

Although information is sparse, it appears that for tx/rxantenna setting: 0=auto, 1=antenna1, 2=antenna2.

-Pete