Traffic Shaper
-
So, I should make static routes "any" at pfsense LAN interface?
-
I want ask you one question, when I make static route at LAN interface the traffic shapper can active on traffic?
-
You need a bunch of static routes:
Interface LAN, subnet vlan1, gateway layer 3 coreswitch
Interface LAN, subnet vlan2, gateway layer 3 coreswitch
Interface LAN, subnet vlan3, gateway layer 3 coreswitch
… -
oh, I need make VLAN ID on pfsense LAN Interface the same VLAN ID at Core Switch? and at pfsense LAN interface I make Bridge with LAN interface, after that I make static route for each VLAN subnet?
-
Hi Hoba,
When I input static route Interface LAN, subnet vlan1, gateway layer 3 coreswitch … --> Network down, from in pfsense I cannot access to Outsite? What's problem?
-
Hi Hoba, I performed static route at LAN Interface with VLAN subnet but it's not run, I monitor just LAN address run other VLAN not run, plshelp me fix this problem
-
Make sure your coreswitch is configured properly and you have all routes in place that are needed at all involved routers/switches.
-
yeah, That is correct because my system run is OK before connect to Pfsense and in Pfsense I in put all Subnet VLAN route.
I don't know what is problem?
Johnnguyen
-
You added static routes at the pfsense for the vlans? You don't need routes for subnets that are directly connected to the pfsense.
-
Hi Hoba,
Examples: I have VLAN 5: Network: 10.100.5.0/24, Gateway: 10.100.5.1, VLAN 6: network 10.100.6.0/24, gateway: 10.100.6.1…
LAN address at pfsense: 10.100.100.5/24
In Layer 3 Core switch I used static route: ip route 0.0.0.0 0.0.0.0 10.100.100.5
Last time (not connect to pfsense) the system running is OK
As you help me, at pfsense LAN address I used static route as follow:
Interface LAN, Network:10.100.5.0/24, gateway layer 3 coreswitch: 10.100.5.1
Interface LAN, Network:10.100.6.0/24, gateway layer 3 coreswitch: 10.100.5.1
...Of course, I don't make routes for subnets that are directly connected to the pfsense.
Pls give me what is wrong?
Regards,
Johnnguyen -
Sorry Interface LAN, Network:10.100.6.0/24, gateway layer 3 coreswitch: 10.100.6.1 (not 10.100.5.1)
-
i think this should be
lan 192.168.5.0/24 gateway "other ip of the switch"the gateway of the static route needs to be in the directly connected subnet
-
Can you speak clearly?
Because I connect direct from Layer3 core Switch to Pix then system run is OK, but I connect from Layer 3 core switch to pfsense to pix then system is down. I make route already but it is not run, I don't know why?
-
Just one very weird thought…are all links at the pfSense up at all (see status>interfaces)? Or do you maybe need a crossovercable between some of the devices? ::)
-
oh, crossovercable between some of the devices? I don't think so because I test "ping" to outside at LAN or WAN pfsense interfase are very good, just other subnets from other VLANs cannot access to outside, although I used static route the same you consult but from LAN pfsense interface I can not ping to gateways of other VLAN
-
Hi all, may I help me to solve this problem?
Regards, Johnnguyen