Errors on boot - v1 embedded on 128 CF
-
Hello,
I am getting the following messages with serial console. I imaged a 128 CF with the v1 release. Any Ideas? Also, if these erros can be ingorned, how do I start the console base setup? I would assume that this should start automatically, but is not per the errors below.
TIA! …and keep up the great work.
init 6 pfSense is now shutting down ... **Warning**: main(config.inc) [[function.main](function.main)]: failed to open stream: No such file or directory in **/etc/rc.conf_mount_rw** on line **32** **Fatal error**: main() [[function.require](function.require)]: Failed opening required 'config.inc' (include_path='.:') in **/etc/rc.conf_mount_rw** on line **32** tar: var/db/rrd/*.rrd: Cannot stat: No such file or directory **Warning**: main(config.inc) [[function.main](function.main)]: failed to open stream: No such file or directory in **/etc/rc.conf_mount_ro** on line **32** **Fatal error**: main() [[function.require](function.require)]: Failed opening required 'config.inc' (include_path='.:') in **/etc/rc.conf_mount_ro** on line **32** Waiting (max 60 seconds) for system process `vnlru' to stop...done Waiting (max 60 seconds) for system process `bufdaemon' to stop...done Waiting (max 60 seconds) for system process `syncer' to stop... Syncing disks, vnodes remaining...0 0 done All buffers synced. Uptime: 23m53s ukphy0: detached miibus0: detached Rebooting... -\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\/boot/kernel/kernel text=0x4a3ce0 |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\data=0x8fe74+0x41138 |/-\|/-\|/-\|/-\|/-\|/-\| /-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\| Hit [Enter] to boot immediately, or any other key for command prompt. Booting [/boot/kernel/kernel]... /-\|/-\Copyright (c) 1992-2006 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 6.1-RELEASE-p10 #0: Fri Oct 13 03:43:07 UTC 2006 sullrich@builder.livebsd.com:/usr/obj.pfSense/usr/src/sys/pfSense_wrap.6 Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: VIA C3 Nehemiah+RNG+ACE (533.35-MHz 686-class CPU) Origin = "CentaurHauls" Id = 0x698 Stepping = 8 Features=0x381b93f <fpu,vme,de,pse,tsc,msr,cx8,sep,mtrr,pge,cmov,pat,mmx,fxsr,sse>real memory = 259981312 (247 MB) avail memory = 245039104 (233 MB) wlan: mac acl policy registered ath_hal: 0.9.16.16 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) cpu0 on motherboard pcib0: <host to="" pci="" bridge=""> pcibus 0 on motherboard pir0: <pci 5="" interrupt="" routing="" table:="" entries=""> on motherboard pci0: <pci bus=""> on pcib0 $PIR: No matching entry for 0.17.INTD $PIR: No matching entry for 0.17.INTD $PIR: No matching entry for 0.17.INTC $PIR: No matching entry for 0.18.INTA pcib1: <pci-pci bridge=""> at device 1.0 on pci0 pci1: <pci bus=""> on pcib1 pci1: <display, vga=""> at device 0.0 (no driver attached) isab0: <pci-isa bridge=""> at device 17.0 on pci0 isa0: <isa bus=""> on isab0 atapci0: <via 8231="" udma100="" controller=""> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xc000-0xc00f at device 17.1 on pci0 ata0: <ata 0="" channel=""> on atapci0 ata1: <ata 1="" channel=""> on atapci0 uhci0: <via 83c572="" usb="" controller=""> port 0xc400-0xc41f irq 5 at device 17.2 on pci0 uhci0: [GIANT-LOCKED] usb0: <via 83c572="" usb="" controller=""> on uhci0 usb0: USB revision 1.0 uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub0: 2 ports with 2 removable, self powered uhci1: <via 83c572="" usb="" controller=""> port 0xc800-0xc81f irq 5 at device 17.3 on pci0 uhci1: [GIANT-LOCKED] usb1: <via 83c572="" usb="" controller=""> on uhci1 usb1: USB revision 1.0 uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1 uhub1: 2 ports with 2 removable, self powered pci0: <bridge> at device 17.4 (no driver attached) pci0: <multimedia, audio=""> at device 17.5 (no driver attached) vr0: <via 10="" vt6102="" rhine="" ii="" 100basetx=""> port 0xd800-0xd8ff mem 0xe4001000-0xe40010ff irq 10 at device 18.0 on pci0 miibus0: <mii bus=""> on vr0 ukphy0: <generic ieee="" 802.3u="" media="" interface=""> on miibus0 ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto vr0: Ethernet address: 00:40:63:e3:d0:50 xl0: <3Com 3c905B-TX Fast Etherlink XL> port 0xdc00-0xdc7f mem 0xe4000000-0xe400007f irq 10 at device 19.0 on pci0 miibus1: <mii bus=""> on xl0 xlphy0: <3Com internal media interface> on miibus1 xlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto xl0: Ethernet address: 00:04:76:34:bf:12 xl1: <3Com 3c905B-TX Fast Etherlink XL> port 0xe000-0xe07f mem 0xe4002000-0xe400207f irq 11 at device 20.0 on pci0 miibus2: <mii bus=""> on xl1 xlphy1: <3Com internal media interface> on miibus2 xlphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto xl1: Ethernet address: 00:04:76:34:c0:1f orm0: <isa option="" rom=""> at iomem 0xc0000-0xcbfff on isa0 ppc0: <parallel port=""> at port 0x378-0x37f irq 7 on isa0 ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode ppbus0: <parallel port="" bus=""> on ppc0 ppi0: <parallel i="" o=""> on ppbus0 sio0 at port 0x3f8-0x3ff irq 4 flags 0x30 on isa0 sio0: type 16550A, console sio1: configured irq 3 not in bitmap of probed irqs 0 sio1: port may not be enabled speaker0: <pc speaker=""> at port 0x61 on isa0 unknown: <pnp0c01> can't assign resources (memory) unknown: <pnp0501> can't assign resources (port) unknown: <pnp0400> can't assign resources (port) Timecounter "TSC" frequency 533354914 Hz quality 800 Timecounters tick every 10.000 msec Fast IPsec: Initialized Security Association Processing. ad2: 122MB <sandisk sdcfb-128="" hdx="" 2.15=""> at ata1-master PIO4 GEOM_LABEL: Label for provider ad2a is ufs/pfSense. GEOM_LABEL: Label for provider ad2d is ufs/pfSenseCfg. Trying to mount root from ufs:/dev/ufs/pfSense ___ ___/ f \ / p \___/ Sense \___/ \ \___/ Welcome to pfSense 1.0-RELEASE on the 'embedded' platform... Setting up embedded specific environment... done. Mounting filesystems... done. Creating symlinks......done. Launching PHP init system... done. Initializing.... **Warning**: main(globals.inc) [[function.main](function.main)]: failed to open stream: No such file or directory in **/etc/rc.bootup** on line **38** **Fatal error**: main() [[function.require](function.require)]: Failed opening required 'globals.inc' (include_path='.:') in **/etc/rc.bootup** on line **38** Starting CRON... done. Syncing packages... **Warning**: main(config.inc) [[function.main](function.main)]: failed to open stream: No such file or directory in **/etc/rc.packages** on line **32** **Fatal error**: main() [[function.require](function.require)]: Failed opening required 'config.inc' (include_path='.:') in **/etc/rc.packages** on line **32** Executing rc.d items... Starting /usr/local/etc/rc.d/*.sh...done. Starting /usr/local/etc/rc.d/*.sh...done. **Warning**: main(config.inc) [[function.main](function.main)]: failed to open stream: No such file or directory in **/etc/rc.conf_mount_ro** on line **32** **Fatal error**: main() [[function.require](function.require)]: Failed opening required 'config.inc' (include_path='.:') in **/etc/rc.conf_moun**</sandisk></pnp0400></pnp0501></pnp0c01></pc></parallel></parallel></parallel></isa></mii></mii></generic></mii></via></multimedia,></bridge></via></via></via></via></ata></ata></via></isa></pci-isa></display,></pci></pci-pci></pci></pci></host></fpu,vme,de,pse,tsc,msr,cx8,sep,mtrr,pge,cmov,pat,mmx,fxsr,sse>
-
Those errors can not be ignored. Is the compact flash media old or new? Try reflashing and/or using a new compact flash card.
-
Thanks for your prompt reply…
The card is brand new.... I will reflash now. I also have a brand new 256 laying around. I'll flash both and post what happans..
Thanks!
-
I am glad I posted.. I reflashed the 128 and now all is well!!
Should I be concerned about the reliablility of this particular card? or is this normal? Also, will hard shutdowns damage the contents of the CF media?
Thanks!
-
Either something went wrong when you flashed that card or the card indeed is somehow flaky.
The cf card in general should not be broken on a hard shutdown as the filesystem is readonly for embedded instralls (unless you hit the exact time when the config.xml is written when something was changed on the webgui).
-
I am currently having this problem on a non embedded image of PFsense, this is the second time this has happened to me. It's not a big deal to reflash except that I loose my config everytime I do so… I'm not sure why it is happening, I think it does have something to do with a hard shutdown because this time it happened after the power went out.