LAN TO LAN WITH 4 VPN TUNNEL (REDUNDANT)

hoba

Try "prefer old IPSEC SA" setting at system>advanced at all ends and see if that makes a difference. If that doesn't help try using smaller lifetimes (like 300 seconds). This way a tunnel should expire after 5 minutes and the backupmachine then will hopefully be able to connect though this means some downtime until the tunnel will be estblished again on failover.

sbyoon

Noted, I will try and let you know of the result. Thank you, Hoba.

martinc_77

I test it and run fine, work's tunnel in OPT-WAN Interface !

LAN
|
(PfSense 1)
| |
ISP1(WAN) ISP2 (OPT-WAN)
| |
| |
( Internet )
|
|
ISP3
|
|
pfSense2 (waiting for mobile clients)
|
LAN

I test this configuration and run ok, but don't automatically.

Both pfsense have static ip.
pfsense 1 have load-balancer
The tunnel is stablish with ISP1 and ISP3 using in pfsense3 mobile clients.
If ISP1 is down i enter in pfsense1 and only change in ipsec WAN Interface to OPT-WAN Interface, and in WAN Gateway write the
OPT-WAN GATEWAY
save and go to diagnostic-ping and all run fine, now vpn is stablished from OPT-WAN PFsense1 to WAN movile client of PFsense 2

the unique problem in this configuration is thats is manuall, but for now work's for me

hoba

Might be easier to have both tunnels configured and just disable the one or the other tunnel for the manual failover.

sbyoon

I've not tested ipsec redundant with carp and ifdepd because I need it at Wrap but the package of ifdepd is not available at embedded system. I'm waiting 1.0 version which will be available package installation at embedded system.

And according to Martinc_77's message the IPsec problem at OPT1 interface was already solved. I tested it with Wrap but IPsec at OPT1 interface does not work yet. Is there anyone who tested it with Wrap? I'd like to know whether only I have this problem. I used pfsense RC2 for testing.

Thank you.

hoba

pfSense 1.0 won't have packagesupport on embedded platforms. Where did you read that? I have tested IPSEC on OPT Interfaces during the hackathon, however I have not tested with hosts coming not from the OPT subnet. In that case it might be possible to add a static route for the remote IPSEC endpoint through the OPT interface gateway.

martinc_77

Dear hoba, IPSEC at OPT Interfase works but only if i add static route! This is a bug ? This is solve in RC3 ??

Tks

hoba

What kind of rule do you need to make this work? Please provide an example.

martinc_77

I need add the next rule in STATIC RUTE HOBA:

–---------------------------------------------------------------------------------------
INTERFASE NETWORK GATEWAY

OPT1 <the other="" end-point="" of="" vpn=""> <the opt1="" gateway="">-----------------------------------------------------------------------------------------

NOTE: OPT1 AND WAN INTERFASE ARE IN MODE LOAD BALANCER

EXAMPLE:

VPN IS RUN IN WAN INTERFASE, THEN, WAN INTERFASE IS DOWN AND I CHANGE IN VPN-IPSEC THE RULE. MANUALLY CHANGE THE WAN INTERFASE WITH OPT1 INTERFASE AND ANY HAPPEND BUT IF I ADD THE PREVIUS STATIC ROUTE VPN IS UP AGAIN WITH OPT1 INTERFASE.

THE QUESTION IS:
BECAUSE NEED ADD THE STATIC ROUTE IF THE RULE IN VPN-IPSEC CONFIGURATION HAS ALL THE INFORMATION THAT PFSENSE NEED ??

THIS IS A BUG??</the></the>

martinc_77

Thear hoba:

Plz need help, cant resolve this problem.I will become crazy
My config is the next.

LAN
|
(PfSense 1)
| |
ISP1
(WAN) ISP2 (OPT-WAN)
| |
| |
( Internet )
|
|
ISP3
|
|
pfSense2 (waiting for mobile clients)
|
LAN

Both pfsense have static ip.
pfsense-1 have load-balancer & squid
The tunnel is stablish with ISP1 and ISP3 using in pfsense3 mobile clients. At less ISP1 is down then Switch to ISP2

The nexts problem happend

when ISP1 is down:

A) I change manually the IPSEC VPN Start Point to ISP2, (Now Tunnel is between ISP2 and
ISP), but not connection is stablish at less add the next static route :
<opt1> <destination 32="" end="" point=""> <opt1-gw>B) PFSENSE Can't resolve DNS at less add the next statis route:
<opt1> <destination 32="" dns="" server=""> <opt1-gw>C) Squid (Running in pfsense 1) don't work any form.

Problems A & B resolve with staric route, C can't but when ISP1 is up again, i need change again the IPSEC VPN Start Point (because isp1 is better) and delete all static route. The really problem is write and delete a static continuously with time I criticize of production that this uses.

My Idea is only change the ISP START POINT MANUALLY (ONLY CHANGE COMBO IN IPS-VPN) and all work fine. It is there possible? Is not, know u other solution. Any solution for squid when WAN is DOWN?</opt1-gw></destination></opt1></opt1-gw></destination></opt1>