Boot/Installation problems with AEWIN Board.
-
Hello all,
I'm new :)
pfsense 1.2RC2 Embedded ( booting from USB-Stick )
AEWIN Technologies Board CB-6971
http://www.aewin.com.tw/–--
Booting [/boot/kernel/kernel]…
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE-p7 #0: Fri Aug 17 18:16:30 EDT 2007
sullrich@builder6.pfsense.com:/usr/obj.pfSense/usr/src/sys/pfSense_wrap.6
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Geode(TM) Integrated Processor by AMD PCS (499.90-MHz 586-class CPU)
Origin = "AuthenticAMD" Id = 0x5a2 Stepping = 2
Features=0x88a93d <fpu,de,pse,tsc,msr,cx8,sep,pge,cmov,clflush,mmx>AMD Features=0xc0400000 <mmx+,3dnow+,3dnow>real memory = 259719168 (247 MB)
avail memory = 244727808 (233 MB)
wlan: mac acl policy registered
K6-family MTRR support enabled (2 registers)
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
cpu0 on motherboard
pcib0: <host to="" pci="" bridge="">pcibus 0 on motherboard
pci0: <pci bus="">on pcib0
pci0: <display, vga="">at device 1.1 (no driver attached)
pci0: <encrypt decrypt,="" entertainment="" crypto="">at device 1.2 (no driver attached)
re0: <realtek 10="" 8139c+="" 100basetx="">port 0xf600-0xf6ff mem 0xeffff000-0xeffff0ff irq 10 at device 9.0 on pci0
miibus0: <mii bus="">on re0
rlphy0: <realtek internal="" media="" interface="">on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
re0: Ethernet address: 00:0d:48:38:04:a5
re0: [FAST]
re1: <realtek 10="" 8139c+="" 100basetx="">port 0xfc00-0xfcff mem 0xefffe000-0xefffe0ff irq 11 at device 10.0 on pci0
miibus1: <mii bus="">on re1
rlphy1: <realtek internal="" media="" interface="">on miibus1
rlphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
re1: Ethernet address: 00:0d:48:38:04:a6
re1: [FAST]
re2: <realtek 10="" 8139c+="" 100basetx="">port 0xfa00-0xfaff mem 0xefffd000-0xefffd0ff irq 7 at device 11.0 on pci0
miibus2: <mii bus="">on re2
rlphy2: <realtek internal="" media="" interface="">on miibus2
rlphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
re2: Ethernet address: 00:0d:48:38:04:a7
re2: [FAST]
re3: <realtek 10="" 8139c+="" 100basetx="">port 0xf800-0xf8ff mem 0xefffc000-0xefffc0ff irq 5 at device 12.0 on pci0
miibus3: <mii bus="">on re3
rlphy3: <realtek internal="" media="" interface="">on miibus3
rlphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
re3: Ethernet address: 00:0d:48:38:04:a8
re3: [FAST]
isab0: <pci-isa bridge="">port 0x6000-0x6007,0x6100-0x61ff,0x6200-0x623f,0x9d00-0x9d7f,0x9c00-0x9c3f at device 15.0 on pci0
isa0: <isa bus="">on isab0
atapci0: <generic ata="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 15.2 on pci0
ata0: <ata 0="" channel="">on atapci0
ata1: <ata 1="" channel="">on atapci0
ohci0: <ohci (generic)="" usb="" controller="">mem 0xefffb000-0xefffbfff irq 10 at device 15.4 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <ohci (generic)="" usb="" controller="">on ohci0
usb0: USB revision 1.0
uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
ehci0: <ehci (generic)="" usb="" 2.0="" controller="">mem 0xefffa000-0xefffafff irq 10 at device 15.5 on pci0
ehci0: [GIANT-LOCKED]
usb1: EHCI version 1.0
usb1: wrong number of companions (1 != 2)
usb1: companion controller, 4 ports each:Fatal trap 12: page fault while in kernel mode
fault virtual address = 0x2c
fault code = supervisor read, page not present
instruction pointer = 0x20:0xc06304ce
stack pointer = 0x28:0xc0c20bac
frame pointer = 0x28:0xc0c20bac
code segment = base 0x0, limit 0xfffff, type 0x1b
= DPL 0, pres 1, def32 1, gran 1
processor eflags = interrupt enabled, resume, IOPL = 0
current process = 0 (swapper)
trap number = 12
panic: page fault
Uptime: 1s
Automatic reboot in 15 seconds - press a key on the console to abortThanks for help… :)</ehci></ohci></ohci></ata></ata></generic></isa></pci-isa></realtek></mii></realtek></realtek></mii></realtek></realtek></mii></realtek></realtek></mii></realtek></encrypt></display,></pci></host></mmx+,3dnow+,3dnow></fpu,de,pse,tsc,msr,cx8,sep,pge,cmov,clflush,mmx>
-
I have found this info:
S Tracker Resp. Description
–------------------------------------------------------------------------------
f usb/103167 imp [ehci] [patch] Transcend JetFlash120 memory stick prob
o usb/112461 usb [ehci] ehci USB 2.0 doesn't work on nforce4
o usb/113672 usb [ehci] [panic] Kernel panic with AEWIN CB6971 <<–- :(
o usb/115400 usb [ehci] Problem with EHCI on ASUS M2N4-SLIon site:
http://lists.freebsd.org/pipermail/freebsd-bugs/2007-September/025785.html -
I think the PC Engines ALIX boards suffer a similar issue that we fixed post-1.2RC2. Does a snapshot from here work?
http://snapshots.pfsense.org/FreeBSD6/RELENG_1_2/ -
Yeah I just got confirmation that the work around in that PR you found is now the default in recent embedded images. Let us know if that works.
-
Yeah, It is working… :)
---snip---
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <ohci (generic)="" usb="" controller="">on ohci0
usb0: USB revision 1.0
uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
pci0: <serial bus,="" usb="">at device 15.5 (no driver attached)
orm0: <isa option="" roms="">at iomem 0xc0000-0xc7fff,0xc8000-0xd27ff,0xef000-0xeffff on isa0
ppc0: parallel port not found.
sio0 at port 0x3f8-0x3ff irq 4 flags 0x30 on isa0
sio0: type 16550A, console
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
speaker0: <pc speaker="">at port 0x61 on isa0
---snap---thanks.. thorsten</pc></isa></serial></ohci>