IPSEC between 2 pfsense boxes over WAN2

warpke

i got it to work a little more

i changed the settings of the WAN2 interface to static (and used the exact same ip, subnetmask and gateway as if it was assigned by dhcp)
now SPD rules are created when i look in "status>ipsec>spd"
but when i look at "status>ipsec>sad" doesn't get filled in…

hopefully i get this to work because these connections are from the same provider, it's more stable and has more bandwith then my pppoe

hoba

If you use static IPs at your opt interface it won't renew it's lease and you'll sooner or later cause IP conflicts in your providers netwok. Please provide the info that I have asked for in my previous post or we can't help you much.

warpke

ok, i'll try to give all information the best i can…

remote pfsense (default WAN):
dhcp
IP address 81.165.XXX.XXX
Gateway 81.165.RRR.RRR

identifier ip adress 81.165.XXX.XXX
preshared key <same secret="">this key is also in preshared keys tab:

Identifier Pre-shared key
81.165.ZZZ.ZZZ <same secret="">Local net Interface
Remote net Remote gw P1 mode P1 Enc. Algo P1 Hash Algo Description

LAN WAN
192.168.1.0/24 81.82.ZZZ.ZZZ aggressive Blowfish SHA1

local pfsense (WAN2):
dhcp
IP address 81.165.ZZZ.ZZZ
Gateway 81.165.YYY.YYY

identifier ip adress 81.165.ZZZ.ZZZ
preshared key <same secret="">
this key is also in preshared keys tab:

Identifier Pre-shared key
81.165.XXX.XXX <same secret="">Local net Interface
Remote net Remote gw P1 mode P1 Enc. Algo P1 Hash Algo Description

LAN WAN2
192.168.0.0/24 81.82.ZZZ.ZZZ aggressive Blowfish SHA1</same></same></same></same>

warpke

http://forum.pfsense.org/index.php/topic,1917.0.html

the last post on this topic explains exactly the same problem, only i have a 1.2-RELEASE

did sbyoon's problem get solved there?

hoba

That thread is already 1.5 years old and was talking about a pre 1.0 version. It should be possible in 1.2, yes. Your settings look valid at a glance though you might want to use identifiers different than the IP-adresses as one if the ends is dynamic (the dhcp one). You even could set this up as mobile client joining the other end (at least one end has to have a static IP though). Please try the following: After adding the route to the remote site through the opwan go to the ipsec settings tab on both machines and simply hit save. This should restart racoon and also dump old SAs. Maybe even try to reboot both ends. Does that solve the issue? Maybe something does not reload correctly when switching the tunnel to a different IP.

warpke

after a lot of trying, i only got it to work when i set the dhcp connection (WAN2) to static

only then the spd rules get created

i know, its not very smart to set a static ip on a dhcp connection, but its a very "static" dhcp adress, i've only seen it change when the network went down for several hours…

there's definitely something not working when you want a tunnel over an opt interface that has dhcp.

hoba

Actually it might be a problem if the dhcp is not yet connected and has no IP when you try to create the tunnel and save settings. I'll take this as discussion to the devchanel but I doubt that a dhcp assigned interface will work with IPSEC reliably anyway (even if the IP does not change).

If your client is not renewing the DHCP lease frequently it will lose the IP (after some hours like you said). The ISP will then assign that IP to someone else though you are using that IP as static. This will mess up their network and they maybe will start to block you to avoid the conflict. You really should not do that.

hoba

We had some discussion about dhcp and IPSEC in the dev-channel and we currently don't see a need to improve this as it won't work reliably anyway. We will be working on something that will allow hostnames as vpn endpoints though. Once that part is done we'll make sure it will work with DHCP or PPPoE WANs too. There is no timeframe for that feature though so don't expect it in the near future.

warpke

ok, thanks a lot anyway :)
i switched the tunnel back to my WAN interface for the time being…

i also had in mind a different sort of setup, because the tunnel works when the dhcp connection goes over the WAN interface

my idea was:

current setup: alternative setup:
WAN: pppoe WAN: dhcp cable
WAN2: dhcp cable WAN2: static ip and gate way: 3com router that has pppoe ability

this is the "pppoe dialer":
http://www.3com.com/prod/nl_BE_EMEA/detail.jsp?tab=features&sku=3CRWER200-75

warpke

this setup seems to work this way,

i've redirected all requests getting to the 3com device to the pfsense on the WAN2, so everything works from my server

al the rest is on the WAN, including the tunnel (the dhcp cable connection)

again, thanks for all the help!!

greets