Please test wireless in latest snapshots
-
Running the snapshot built "Fri Jul 25 13:43:33 EDT 2008". Wireless doesn't work when bridged with LAN. However, it does work if setup on it's own subnet.
-
Did some testing, not sure if anyone found this before. Anyway…
After bridging the Wireless with the LAN, the following is appears when running dmesg:
bridge0: invalid MTU for re0
I checked the bridge0 interface, and it had an MTU of 2290, just like ath0. Obviosly that MTU is invalid for a standard ethernet NIC, thus it refuses to join bridge.
From there, I attempted to set ath0 (Wireless) MTU via pfSense webConfigurator, but the MTU setting was ignored. So, I manually set it via the shell. However, bridge0 still had an MTU of 2290 after changing ath0's MTU.
Finally, I decided to manually destroy bridge0, and recreate it. Now, that I had ath0 set with an MTU of 1500, both ath0 and re0 would have the same MTU.
ifconfig bridge0 destroy
ifconfig bridge create
ifconfig bridge0 addm ath0 addm re0 upAfter recreating the bridge with both devices having an MTU of 1500, the bridge worked properly. The only left was to create a firewall rule to allow traffic in on the Wireless interface, which I did via the webConfigurator.
Hopefully the above is of use to somebody.
-
@JTY:
Did some testing, not sure if anyone found this before. Anyway…
After bridging the Wireless with the LAN, the following is appears when running dmesg:
bridge0: invalid MTU for re0
I checked the bridge0 interface, and it had an MTU of 2290, just like ath0. Obviosly that MTU is invalid for a standard ethernet NIC, thus it refuses to join bridge.
From there, I attempted to set ath0 (Wireless) MTU via pfSense webConfigurator, but the MTU setting was ignored. So, I manually set it via the shell. However, bridge0 still had an MTU of 2290 after changing ath0's MTU.
Finally, I decided to manually destroy bridge0, and recreate it. Now, that I had ath0 set with an MTU of 1500, both ath0 and re0 would have the same MTU.
ifconfig bridge0 destroy
ifconfig bridge create
ifconfig bridge0 addm ath0 addm re0 upAfter recreating the bridge with both devices having an MTU of 1500, the bridge worked properly. The only left was to create a firewall rule to allow traffic in on the Wireless interface, which I did via the webConfigurator.
Hopefully the above is of use to somebody.
Hi,
thank you…
I can verify this... I had the exact same problem, manually changing the MTU and recreating the Bridge worked perfectly...Now I can finally use Itunes remote on my Ipod ;D
-
after resetting the interface config and this time just choosing 802.11g and running as an accesspoint I've had no more problems, other than the athstats error.
Thanks guys t is good to finally have a usable wireless connection.
-
@JTY:
After bridging the Wireless with the LAN, the following is appears when running dmesg:
bridge0: invalid MTU for re0
I checked the bridge0 interface, and it had an MTU of 2290, just like ath0.
How did your ath0 get a MTU of 2290? I just setup a LAN ath bridged to WAN and did not see that, it defaults to 1500.
-
@cmb:
@JTY:
After bridging the Wireless with the LAN, the following is appears when running dmesg:
bridge0: invalid MTU for re0
I checked the bridge0 interface, and it had an MTU of 2290, just like ath0.
How did your ath0 get a MTU of 2290? I just setup a LAN ath bridged to WAN and did not see that, it defaults to 1500.
I had done a fresh install of 1.2.1 TESTING, and setup OPT1 (ath0) during install. Once I rebooted, ath0 was set with an MTU of 2290.
-
i am running build built on Sat Jul 26 21:27:41 EDT 2008
When I was configuring the interface I had to manualing change the mtu to 1500
After I changed it I had no more problems.
I tried to reproduce the error by deleting the interface and reconfiguring it and nothing seemed to reproduce the change in mtu to 2290.
I then remembered I initially tried to configure turbo G in the wireless configuration>standard drop down menu. And used channel 6 channel list, which is list as a turbo G channel.
When I configure my card to these settings I get this
ifconfig ath0
ath0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 2290
ether 00:11:95:c2:27:a9
inet6 fe80::211:95ff:fec2:27a9%ath0 prefixlen 64 scopeid 0x3
inet 192.168.2.1 netmask 0xffffff00 broadcast 192.168.2.255
media: IEEE 802.11 Wireless Ethernet autoselect mode 11g <hostap>status: associated
ssid TAMU channel 6 (2437 Mhz 11g) bssid 00:11:95:c2:27:a9
authmode WPA privacy MIXED deftxkey 2 AES-CCM 2:128-bit txpower 31.5
scanvalid 60 bgscan bgscanintvl 300 bgscanidle 250 roam:rssi11g 7
roam:rate11g 5 pureg protmode RTSCTS wme burst dtimperiod 1Note even though turbo G is listed on the dropdown menu's it is not supported in freebsd 7(last line in man pages).
I don't have time to confirm my last statement but I believe I read this about a week ago and I doubt it has changed since then.
Hope this helps.</hostap></up,broadcast,running,simplex,multicast>
-
OK. I just tried deleting the OPT1 (ath0), then rebooting. After rebooting, I recreated the interface, and once again it was set with an MTU of 2290. And, no I'm not using Turbo mode.
-
Installed the pfSense-Full-Update-1.2.1-TESTING-SNAPSHOT-20080727-1206
I ran the ifconfig command and got this;
fxp0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
fxp1: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
ath0: flags=8943 <up,broadcast,running,promisc,simplex,multicast>metric 0 mtu 2290
lo0: flags=8049 <up,loopback,running,multicast>metric 0 mtu 16384
bridge0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 2290This is from 1.2 -stable ifconfig log. (works)
fxp0: flags=8943 <up,broadcast,running,promisc,simplex,multicast>mtu 1500
fxp1: flags=8843 <up,broadcast,running,simplex,multicast>mtu 1500
ath0: flags=8943 <up,broadcast,running,promisc,simplex,multicast>mtu 1500
lo0: flags=8049 <up,loopback,running,multicast>mtu 16384
pfsync0: flags=41 <up,running>mtu 2020
pflog0: flags=100 <promisc>mtu 33208
enc0: flags=0<> mtu 1536
bridge0: flags=8843 <up,broadcast,running,simplex,multicast>mtu 1500</up,broadcast,running,simplex,multicast></promisc></up,running></up,loopback,running,multicast></up,broadcast,running,promisc,simplex,multicast></up,broadcast,running,simplex,multicast></up,broadcast,running,promisc,simplex,multicast></up,broadcast,running,simplex,multicast></up,loopback,running,multicast></up,broadcast,running,promisc,simplex,multicast></up,broadcast,running,simplex,multicast></up,broadcast,running,simplex,multicast> -
yeah it won't let me bridge my wireless with my LAN either, i mean it says it does it, but then it just sits on "learning" in the Interfaces tab in the "Bridge (bridge0)" category.
EDIT: Update, about 20-30 mins after bridging the connections unsuccessfully the router rebooted on it's own which worried me, but then upon loading the connections seem have to successfully bridge!
-
Updated to the latest snapshot, and the problem continues. I have done further testing on this. When booting up the interface is now showing an MTU of 1500. However, after switching to Access Point mode, it automatically changes MTU to 2290. (Disregard the IP, I tested without bridging so I could try to determine which feature/function caused the MTU to change.)
Before enabling AP mode:
ifconfig ath0
ath0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
ether 00:c0:a8:c1:6b:82
inet6 fe80::2c0:a8ff:fec1:6b82%ath0 prefixlen 64 scopeid 0x2
inet 192.168.2.1 netmask 0xffffffff broadcast 192.168.2.1
media: IEEE 802.11 Wireless Ethernet autoselect mode 11g
status: no carrier
ssid GoatsBlood channel 1 (2412 Mhz 11g)
authmode OPEN privacy OFF txpower 31.5 bmiss 7 scanvalid 60 bgscan
bgscanintvl 300 bgscanidle 250 roam:rssi11g 7 roam:rate11g 5
protmode OFF burstifconfig ath0
ath0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 2290
ether 00:c0:a8:c1:6b:82
inet6 fe80::2c0:a8ff:fec1:6b82%ath0 prefixlen 64 scopeid 0x2
inet 192.168.2.1 netmask 0xffffffff broadcast 192.168.2.1
media: IEEE 802.11 Wireless Ethernet autoselect mode 11g <hostap>status: associated
ssid GoatsBlood channel 1 (2412 Mhz 11g) bssid 00:c0:a8:c1:6b:82
authmode WPA privacy MIXED deftxkey 2 TKIP 2:128-bit txpower 31.5
scanvalid 60 bgscan bgscanintvl 300 bgscanidle 250 roam:rssi11g 7
roam:rate11g 5 protmode OFF burst -apbridge dtimperiod 1</hostap></up,broadcast,running,simplex,multicast></up,broadcast,running,simplex,multicast> -
It's definitely Access Point which is causing the MTU to be 2290. If I switch the interface to Ad-Hoc, the MTU is 1500. The moment I switch it back to Access Point, it becomes 2290. My guess is, this is some behavior in the driver itself. Perhaps pfsense could do a 'ifconfig ath0 mtu 1500' after setting the interface parameters.
-
We commited a change to enforce mtu 1500. Please try a recent snapshot.
-
I have upgraded to the latest RC1 snapshot, and the problem still continues. Once Access Point is enabled, ath0 changes MTU to 2290.
-
I decided to ask on the freebsd-net mailing list, and the response I got was, that 2290 is the default MTU for 802.11.
-
Any chance hostapd is resetting the MTU to 2290? I just looked at it's source code, and it appears that it may be setting it (see line 86), http://hostap.epitest.fi/hostapd/devel/hostapd_8h-source.html and (see line 241) http://hostap.epitest.fi/hostapd/devel/driver__bsd_8c-source.html.
-
weird… the last ifconfig we run on bringing up a wireless card is now 'mtu 1500'. My ath card hasn't shown this behavior in hostap mode, it's always shown 1500 without this recent change so it's not an issue with every ath card.
If anyone finds additional information on this please let us know. I'll be doing more wireless testing as time permits over the next week.
-
Ok heres the deal with me. (20080730-0226)
With no security It works fine, I get an IP address, With WEP It also works fine.
As soon as I enable WPA It will never connect. Even after I disable WPA and either choose no security or wep it still deos NOT work.
Can anyone else test with WEP or no security on initial install BEFORE enabling WPA to confirm it's the same with other hardware?
I have not had a chance to look at the MTU in this process, but if it does happen only when WPA get's turned on it may point us in the correct direction.
(Utilizing a Cisco ABG card in an Acer5620z Laptop.)
Many thanks,
Tom -
pfSense-Full-Update-1.2.1-RC1-20080730-0232
mtu 2290 on ath0 and bridge0
-
THANK YOU!
ifconfig ath1 mtu 1500
ifconfig bridge0 destroy
ifconfig bridge create
ifconfig bridge0 addm ath1 addm axe0 up
(where axe0 is my LAN interface and ath1 is my Wireless (opt1) interface)Works perfectly!
NOTE If you do not have any security or WEP the MTU does not set itself to 2290 so wherever the problem it is, it's only when you enable WPA. Hopefully they can find the piece of code, or create some to set the interface MTU teardown the bridge and recreate!!
@JTY:
Did some testing, not sure if anyone found this before. Anyway…
After bridging the Wireless with the LAN, the following is appears when running dmesg:
bridge0: invalid MTU for re0
I checked the bridge0 interface, and it had an MTU of 2290, just like ath0. Obviosly that MTU is invalid for a standard ethernet NIC, thus it refuses to join bridge.
From there, I attempted to set ath0 (Wireless) MTU via pfSense webConfigurator, but the MTU setting was ignored. So, I manually set it via the shell. However, bridge0 still had an MTU of 2290 after changing ath0's MTU.
Finally, I decided to manually destroy bridge0, and recreate it. Now, that I had ath0 set with an MTU of 1500, both ath0 and re0 would have the same MTU.
ifconfig bridge0 destroy
ifconfig bridge create
ifconfig bridge0 addm ath0 addm re0 upAfter recreating the bridge with both devices having an MTU of 1500, the bridge worked properly. The only left was to create a firewall rule to allow traffic in on the Wireless interface, which I did via the webConfigurator.
Hopefully the above is of use to somebody.