Successful Install on Watchguard Firebox X700!
-
Ok below is my screen from the serial cable. I ordered a Hitachi 4gig microdrive off ebay, and this morning did a full install to it via a bootable cdrom on another machine. I had a usb-cf card reader that was attached to the computer. After it got done installing, I took it out and slid it into the firebox cf slot.
Will ufs:ad0 be my microdrive?
Copyright
1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE-p11 #0: Sun Feb 24 16:32:58 EST 2008
sullrich@builder6.pfsense.com:/usr/obj.pfSense/usr/src/sys/pfSense.6
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) III CPU - S 1400MHz (1403.19-MHz 686-class CPU)Origin = "GenuineIntel" Id = 0x6b4 Stepping = 4
Features=0x383f9ff<fpu,vme,de,pse,tsc,msr,pae,mce,cx8,sep,mtrr,p ="" <br="">T,PSE36,MMX,FXSR,SSE>
real memory = 268435456 (256 MB)
avail memory = 253263872 (241 MB)
wlan: mac acl policy registered
kbd1 at kbdmux0
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
cpu0 on motherboard
pcib0: <intel 82815="" (i815="" gmch)="" host="" to="" hub="" bridge="">pcibus 0 on motherboard
pir0: <pci 11="" interrupt="" routing="" table:="" entries="">on motherboard
$PIR: Using invalid BIOS IRQ 9 from 2.13.INTA for link 0x63
pci0: <pci bus="">on pcib0
pcib1: <pcibios pci-pci="" bridge="">at device 30.0 on pci0
pci2: <pci bus="">on pcib1
pci2: <unknown>at device 6.0 (no driver attached)
re0: <realtek 10="" 8139c+="" 100basetx="">port 0xd500-0xd5ff mem 0xefefa000-0xefefa1ff
irq 10 at device 9.0 on pci2
miibus0: <mii bus="">on re0
rlphy0: <realtek internal="" media="" interface="">on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
re0: Ethernet address: 00:90:7f:31:0e:f2
re0: [FAST]
re1: <realtek 10="" 8139c+="" 100basetx="">port 0xd600-0xd6ff mem 0xefefb000-0xefefb1ff
irq 5 at device 10.0 on pci2
miibus1: <mii bus="">on re1
rlphy1: <realtek internal="" media="" interface="">on miibus1
rlphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
re1: Ethernet address: 00:90:7f:31:0e:f3
re1: [FAST]
re2: <realtek 10="" 8139c+="" 100basetx="">port 0xd900-0xd9ff mem 0xefefc000-0xefefc1ff
irq 11 at device 11.0 on pci2
miibus2: <mii bus="">on re2
rlphy2: <realtek internal="" media="" interface="">on miibus2
rlphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
re2: Ethernet address: 00:90:7f:31:0e:f4
re2: [FAST]
re3: <realtek 10="" 8139c+="" 100basetx="">port 0xda
irq 12 at device 12.0 on pci2
miibus3: <mii bus="">on re3
rlphy3: <realtek internal="" media="" interface="">on miibus3
rlphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
re3: Ethernet address: 00:90:7f:31:0e:f5
re3: [FAST]
re4: <realtek 10="" 8139c+="" 100basetx="">port 0xdd00-0xddff mem 0xefefe000-0xefefe1ff
irq 9 at device 13.0 on pci2
miibus4: <mii bus="">on re4
rlphy4: <realtek internal="" media="" interface="">on miibus4
rlphy4: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
re4: Ethernet address: 00:90:7f:31:0e:f6
re4: [FAST]
re5: <realtek 10="" 8139c+="" 100basetx="">port 0xde00-0xdeff mem 0xefeff000-0xefeff1ff
irq 6 at device 14.0 on pci2
miibus5: <mii bus="">on re5
rlphy5: <realtek internal="" media="" interface="">on miibus5
rlphy5: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
re5: Ethernet address: 00:90:7f:31:0e:f7
re5: [FAST]
isab0: <pci-isa bridge="">at device 31.0 on pci0
isa0: <isa bus="">on isab0
atapci0: <intel ich2="" udma100="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x37
6,0xff00-0xff0f at device 31.1 on pci0
ata0: <ata 0="" channel="">on atapci0
ata1: <ata 1="" channel="">on atapci0
pmtimer0 on isa0
orm0: <isa option="" rom="">at iomem 0xe0000-0xe0fff on isa0
atkbdc0: <keyboard controller="" (i8042)="">at port 0x60,0x64 on isa0
atkbd0: <at keyboard="">irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
ppc0: <parallel port="">at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
ppbus0: <parallel port="" bus="">on ppc0
lpt0: <printer>on ppbus0
lpt0: Interrupt-driven port
ppi0: <parallel i="" o="">on ppbus0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
unknown: <pnp0c01>can't assign resources (memory)
unknown: <pnp0303>can't assign resources (port)
speaker0: <pc speaker="">at port 0x61 on isa0
unknown: <pnp0501>can't assign resources (port)
unknown: <pnp0401>can't assign resources (port)
RTC BIOS diagnostic error 20 <config_unit>Timecounter "TSC" frequency 1403186855 Hz quality 800
Timecounters tick every 1.000 msec
Fast IPsec: Initialized Security Association Processing.
ad0: 3906MB <hms360604d5cf00 dp4ec30h="">at ata0-master UDMA33
ad0: FAILURE - READ_DMA timed out LBA=7999485
ad0: FAILURE - READ_DMA timed out LBA=7999471
ad0: FAILURE - READ_DMA timed out LBA=7999484
ad0: FAILURE - READ_DMA timed out LBA=7999487
ad0: FAILURE - READ_DMA timed out LBA=7999425
ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=7999487
ad0: TIMEOUT - READ_DMA retrying (0 retries left) LBA=7999487
ad0: FAILURE - READ_DMA timed out LBA=7999487
ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=7999487
ad0: TIMEOUT - READ_DMA retrying (0 retries left) LBA=7999487
ad0: FAILURE - READ_DMA timed out LBA=7999487
ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=128
ad0: TIMEOUT - READ_DMA retrying (0 retries left) LBA=128
ad0: FAILURE - READ_DMA timed out LBA=128
ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=16
ad0: TIMEOUT - READ_DMA retrying (0 retries left) LBA=16
ad0: FAILURE - READ_DMA timed out L
ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=0
ad0: TIMEOUT - READ_DMA retrying (0 retries left) LBA=0
ad0: FAILURE - READ_DMA timed out LBA=0
ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=512
ad0: TIMEOUT - READ_DMA retrying (0 retries left) LBA=512
ad0: FAILURE - READ_DMA timed out LBA=512
ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=64
ad0: TIMEOUT - READ_DMA retrying (0 retries left) LBA=64
ad0: FAILURE - READ_DMA timed out LBA=64
ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=0
ad0: TIMEOUT - READ_DMA retrying (0 retries left) LBA=0
ad0: FAILURE - READ_DMA timed out LBA=0
ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=2
ad0: TIMEOUT - READ_DMA retrying (0 retries left) LBA=2
ad0: FAILURE - READ_DMA timed out LBA=2
ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=16
ad0: TIMEOUT - READ_DMA retrying (0 retries left) LBA=16
ad0: FAILURE - READ_DMA timed out LBA=16
ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=128
ad0: TIMEOUT - READ_DMA retrying (0 retries left) LBA=128
ad0: FAILURE - READ_DMA timed out LBA=128
ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=0
ad0: TIMEOUT - READ_DMA retrying (0 retries left) LBA=0
ad0: FAILURE - READ_DMA timed out LBA=0
Trying to mount root from ufs:/dev/da0s1aManual root filesystem specification:
<fstype>:<device> Mount <device>using filesystem <fstype>eg. ufs:da0s1a
? List valid disk boot devices
<empty line=""> Abort manual inputmountroot></empty></fstype></device></device></fstype></hms360604d5cf00></config_unit></pnp0401></pnp0501></pc></pnp0303></pnp0c01></parallel></printer></parallel></parallel></at></keyboard></isa></ata></ata></intel></isa></pci-isa></realtek></mii></realtek></realtek></mii></realtek></realtek></mii></realtek></realtek></mii></realtek></realtek></mii></realtek></realtek></mii></realtek></unknown></pci></pcibios></pci></pci></intel></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,sep,mtrr,p >
-
When I try ad0 I get:
mountroot> ufs:ad0
Trying to mount root from ufs:ad0
ad0: TIMEOUT - READ_DMA retrying (1 retry left) LBA=128
ad0: TIMEOUT - READ_DMA retrying (0 retries left) LBA=128
ad0: FAILURE - READ_DMA timed out LBA=128Manual root filesystem specification:
<fstype>:<device> Mount <device>using filesystem <fstype>eg. ufs:da0s1a
? List valid disk boot devices
<empty line=""> Abort manual inputmountroot>
…even though when I display the bootable devices it gives me:
List of GEOM managed disk devices:
ad0</empty></fstype></device></device></fstype> -
Works perfectly! So if you have any old p3s laying around, swap em out and get a little more performance! Also these boards do support 512 MB sticks of PC133, so as soon as I find some I will be upgrading that as well.
I just stuck in a 512meg stick into mine and it still registers as 256. I had this problem on the old IP330's as well.
-
I would try setting hw.ata.ata_dma=0 in the loader.conf to see if that helps getting the microdrive to boot.
-
I would try setting hw.ata.ata_dma=0 in the loader.conf to see if that helps getting the microdrive to boot.
How would I go about doing that?
-
Sorry to be a noob and ask this - but been following this thread faithfully and finally decided to take the plunge and try pfSense on my Firebox x700 - however - having difficulties getting the Hyperterminal commands to "take" - more specifically - I get to see the boot sequence and it asks me for the "mount location" - and then I attempt to type in the commands to mount the hard drive and I am not getting "ENTER" to work. Any clues?
Great resource and forums by the way peeps - thx for all the hard work and effort you guys have done in making pfSense work as well as it has.
Dayblade
-
-
So - after downloading a new terminal program - i can now get the Firebox to answer me - now however - I am getting a "ROOT MOUNT FAILURE"… when following the OP directions. Suggestions as to next steps? I also tried doing AUTOMATIC - and that did not work either.
Dayblade
-
Drop to a shell and enter:
echo 'hw.ata.ata_dma="0"' >>/boot/loader.confAt this point, there is no ssh access, only console. Is there a way to break out of this harddrive mounting screen?
-
WOOT!!!! - finally got it working.
Had to download a new terminal program so that it would recognize the "ENTERS" - Windows Proggy - Indigo Terminal 2.
Had some hiccups with certain character counts so had to enter a few characters "twice" … ie ad2s1a was ad22s1a etc.
Will keep ya posted.
Dayblade
-
At this point, there is no ssh access, only console. Is there a way to break out of this harddrive mounting screen?
You could pull the card and add the line on another box or you could try:
set hw.ata.ata_dma=0
boot -
So just for fun and curiosity, I wrote a m0n0wall image to a 512meg cf card and stuck it into the watchguard cf slot. It booted with no issue. I then put my atheros mini-pci wireless card into the mini-pci slot, and it recognized it immediately.
I too, am getting watchdog timeout's. I had a ping going from my desktop and randomly, Id say every 10-20 seconds, my ping would timeout, which would then be followed by a watchdog timeout registering in my serial console window. At the time, I only had 2 cables plugged in, internet to interface re0, and lan to re1. Most of the watchdog timeouts were on re1.
So I find it interesting the watchdog timeouts are both on pfsense and m0n0wall.
I have also installed a 512meg memory stick, but only 256meg is recognized. Are there jumpers that need to be moved in order to see the rest of the memory?
-
What kind of serial cable are you guys using? I picked one of these boxes up on eBay and unfortunately it didn't come with one - figured I could use the console cable for my Linksys SRW2016, but I get nothing on-screen.
-
the console cable for my Linksys SRW2016, but I get nothing on-screen.
But that's due to the fact that the Linksys cable is all but wired in a known standard.
I have some SRW2008 switches at home and tried that serial cable for a console connection to some other equipment.
Well, grabbing my Null-modem cable worked as expected, the Linksys did not.
And my Null-modem cable didn't work with the Linksys switch, of course. Didn't have the gutts to actually measure the pinout, just labeled it 'Linksys switch ONLY'… -
Figured as much really as the Linksys cables are straight-thru cables.
Oh well, off I go to eBay to pick up a USB -> null modem combo. Sure it'll come in handy again :)On a slightly related note, have anyone found the keyboard pinouts on the x700 motherboard? I've only had a quick look (only received it today) but nothing stands out as the prime suspect.
-
Figured as much really as the Linksys cables are straight-thru cables.
Then they have the connectors wrong!
Null-modem cable should be {DB9-female - DB9-female} and
straight through should be {DB9-female - DB9-male} making it an extension.Everything else is proprietary.
-
Well, to be perfectly honest - that's not the only thing they have wrong :) Took me a good while to flash the SRW2016s to an acceptable firmware which actually included all the features they were advertised as having. Good switches once that was done though.
Oh well, nullmodem cable on it's way now. Grabbed a 5GB microdrive also to see if that'll be recognized so guess I'm shelfing the project for a couple more days.
Hmm, whilst I'm at it - anyone got ideas on a mini-pci wifi card I could stick in it?
-
I preferr this card http://pcengines.ch/wlm54g23.htm or this card http://pcengines.ch/wlm54sag23.htm depending on if i need 802.11a support or not.
I never had problems with them :)
(except on pfSense 1.0 but that was because of a bad client)… -
Again, has anyone upgraded the memory on these boxes and gotten it to see the additional? I placed a 512meg module in the box, and it still registers at 256meg. I tried 2 separate sticks.
Perhaps jumper settings somewhere on the board?
-
Anyone have any updates? Such as successful additional memory, no more watchdog timeouts, installs on a microdrive?
