Configure Load Balancer & Failed over

kambeeng

Afrugone many thanks

Can i see ur firewall rule and NAT plz….
its very help me ...........

kambeeng

Afrugone

What happend with this , i have to set and showing this error,
can u help me plz

System Gateways : Edit Gateways

Group Name : Load Balance
Gateway Priority : Tier 1 VIGOR GATEWAY (WAN)
Tier 2 DLINK GATEWAY (OPT1)

Description Loadbalance

when i tried to save that configuration its showing error

X the following input error were detected :
No gateway have been selected to be use in this group

and showing my configuration tier1 back to the "NEVER"

thnks

m3isp

Since you copied my post from another thread and reposted it under your name I figured the least I could do would be to solve your problem for you. To prevent the Tier never error from occurring remove all special characters from the names of your gateways. Special characters seem to include capital letters and spaces. I have not tested it with numbers but I would leave them out for good measure.

Regards
M3isp

kambeeng

hello M3isp

I have succeded configure that one…
i have one question.... in gateway everythink is ok.. status of gateway also but load balancer not worked, just only wan1 worked.

how to configure in firewall rule and nat rule for make succeded that load balancing.

in status of gateway seems to be ok.

tks

Guest

The only think not working for me is failover, any special hint for this?

m3isp

Firewall Rule:

Proto: *
Source: LAN Net
Port:*
Destination:*
Port:*
Gateway:"Select load balanced gate from drop down"
Queue:none
Schedule:n/a

Not sure what the Outbound NAT would be for 1.3 should be something like:
Interface:?
Source: 192.168.0.1/24 "or whatever you use"
Destination: Any
Gateway:"Put Load Balanced Gateway Here"

I haven't checked AON in 1.3 so I'm not sure if using AON is even an option for this. Maybe someone else can comment.

BTW I'm not an authority on PFSense by any means. Please correct me if I make a mistake.

Regards
M3isp

kambeeng

i have try setting like u .. but a load balance not working.
only one isp running….
probably i use 2 isp

Guest

I've updated to latest versions, and now everything is working including failover.

kambeeng

Thanks Afrugone

I will try. ;D

databeestje

Description of how tiers work.

This might be best explained by viewing you configuration on the Status -> Gateways -> Gateway Groups tab.

All gateways within the same tier will load balance.
When all gateways in the tier are down we will use the next tier with a gateway.

For example, when you want to load balance WAN1, WAN2 and use WAN3 if all else fails, then:
WAN1 Tier 1
WAN2 Tier 1
WAN3 Tier 2

When You want to load balance WAN1, WAN2 and WAN3, then:
WAN1 Tier 1
WAN2 Tier 1
WAN3 Tier 1

When You want to failover from WAN 1, to load balancing WAN2 and WAN3, then:
WAN1 Tier 1
WAN2 Tier 2
WAN3 Tier 3

I hope this explains.

kambeeng

Thnk u databeestje

I already implemented about that.

kambeeng

kambeeng

Hello databeestje

Need ur help pls.

I have configure load balance also failed over as ur suggested.
i indicator are working…. which both gateway Wan1 & Wan2.
Btw if i disconnected modem one of them.

For example.

I use 2 modem adsl with speed 1mbps.
1. Vigor (Daytrex)
2. DLINK

everything is ok if i used both modem i mine (LoadBalance) speed will increased.
But if I disconnected Vigor and I want used only DLINK, its not working its diferent with 1.2 , everything is better both loadbalance and failde over.

any suggested for this case

regards

Kambeeng

Perry

It's wild guess, as i haven't tried 1.3 loadbalancing yet, but could it be a DNS resolve problem.
try 208.69.34.230 in browser

kambeeng

Hello perry….

my dns its ok... btw which dns u give to me, its open dns