Successful Install on Watchguard Firebox X700!
-
I am looking to do this to my x700 after i realised it doesnt do what I want it to do
I have put a hd into a laptop and tried to install but I am getting an error message about not enough network interfaces to setup
so I will try in a pc with multiple network cards in however when I then put it into the watchguard will it auto detect the drivers for the watchguard ethernet ports?
-
Is the watchdog timeouts issue still ongoing.
Looking to replace my VM of pfSense with either an X700 or an Alix solution.
Does anyone know what the relative performance of the X700 (Celeron 1.2GHz I understand) vs the 500MHz AMD Geode CPU.
Thanks,
Dean
-
Hi everyone,
I was given an X700 and I decided to put pfSense on it. But I can't connect my laptop to the Guard using serial. Here's my setup :
- Null modem cable + USB > serial adapter
- Putty
- 115200 bits/s, 8-n-1 (I also tried lower bit-rate)
Putty's window is blacker than black ???
Anyone got an idea on this ? -
- 115200 bits/s, 8-n-1 (I also tried lower bit-rate)
I had the same problem, and discovered that i was using a wrong cable.
And the serial settings should be : 9600 bits/s, 8-n-1 -
Does anyone know if these will take ECC ram? A lot easier and cheaper to find 512mb ECC ram sticks then non ecc where i am
-
I have a 512MB PC100 ECC which I was going to try in it
Can let you know tonight
Just wanted to say how great this guide was for setting up my x700
I have been taking photos, so will do my own mini write up to aid future x700 modders :)
-
Does anyone know if these will take ECC ram? A lot easier and cheaper to find 512mb ECC ram sticks then non ecc where i am
I belive normal ECC should work but registered ECC will most likely not. Haven't tested tho.
-
Has any one made embedded image with LCDproc included for x700?
-
Purchased an X500 and will install pfSense shortly.
Are there any advantages (apart from capacity) to installing on a HD as opposed to a CF card?
Thanks,
-
Full unrestricted packages.
-
Has any one made embedded image with LCDproc included for x700?
I can make a ghost image for you if you want. ;D
-
Has any one made embedded image with LCDproc included for x700?
I can make a ghost image for you if you want. ;D
ok :)
-
Complete and utter noob here so please be gentle!!
I've managed to get lumped with a faulty X700. I'm guessing the OS is shafted so it'd make an ideal candidate for a pfsense install.
As I'm fairly Linux illiterate (about 6 months mild exposure), what would be better for me… a hdd install or a CF install?I'm wanted to use it to firewall and route with NAT my 50Mb cable connection, running Developement Web and Mail servers.
TIA
Pete
-
Definately the HDD option
I am currently in the process of writing a little guide with photos to make things easier for those that dont understand it all
Luckily I had an old external hard drive (USB powered one) which was faulty. Inside them there is basically an IDE laptop drive 2.5" and a tiny circuit board which connects the IDE HDD to a mini USB connector
I plugged this into a spare 80GB IDE Laptop drive I had and plugged in a USB to mini USB.
Connect the USB to a PC and disconnect any other hard drives then boot from CD and put the pfSense Live CD in, and once booted you can install to the HDD which is pretty easy if you just follow the steps
PC will need 2 network ports in it though
I was going to Ghost my drive, but the ghost tool I have just wanted to ghost the whole drive including empty space which was going to take hours
I havent yet but my plan is to put the LCD stuff on too
A further step for me is to reduce the noise of the X700 and so I researched and found the 3 fans in the back are 40mm x 10mm and the quietest ones I could find were 14DBa so I have ordered 3 of these:
https://www.overclockers.co.uk/showproduct.php?prodid=FG-029-SY
They will arrive tomorrow, however they will have the wrong connector on them so I will have to solder the old connectors on once I have tested them
I will take some more photos as I do this and once done I will post up the guide
-
Thanks for the info.
I've got a dead laptop with an IDE drive I can salvage and I'm a reg on the OCUK forums so I get free shipping from them so I'll might order up some of those fans - or maybe I'll get the Ultra version…. they are 19dBA over 14dBA (ie still pretty much silent) but they offer 20% more air throughput.
Might see if I can get some more RAM cheap too.
-
Damn it, I am a member on the OCUK forums and didnt know that… gutted
To be honest, even with the current fans and the watchguard sat on a carpet in a heated room near a radiator its not getting even warm at all
-
If you have more than 150 posts on there (I think) you get free shipping.
Managed to get a 512Mb double sided DIMM from a local store for £11 - Can't find my console cable atm tho.Update…. OK, looks like the X700 is duff.
To be fair, I'd not tried it before I popped the RAM in. When it boots the display stays blank and there is a rapid clicking coming from the speaker. I put the original ram back in, cleared the CMOS and swapped the CPU. Still the same. -
As of October 25, 2009, Watchguard's original X-core series (X500, X700, X1000, X2500) is end-of life. That means no more updates, so you should be able to find them cheap on eBay, although there are plenty of folks still trying to get full price. All these models were license-upgradable, so the hardware is identical. You should be paying under $100 US for one – which is way cheaper than a new alix -- and gets you six ethernet ports.
Watchguard's end-of-life announcements: http://www.watchguard.com/products/resources/end-of-life-policy.asp
Photos of my X700's guts: http://cw.sampas.net/gallery2/v/Firebox/
Boot log (dmesg): http://cw.sampas.net/watchguardTerminal.TXTWhile the Safenet crypto card is recognized in pfsense, it isn't used. I tried replacing it with the Soekris crypto card that works fine in Alix but it doesn't work on the X700. (I'm still running down that error.)
-
While the Safenet crypto card is recognized in pfsense, it isn't used. I tried replacing it with the Soekris crypto card that works fine in Alix but it doesn't work on the X700. (I'm still running down that error.)
Interesting. If you look at the DMESG from /status.php does it just recognize it, or does it load the safe driver and that is not working? If the driver is not loaded, you could always try kldloading the module from FBSD 7.2.
P.S. Nice Airhead -
I'm loving my pfGuard. Here's some truncated dmesg output. It seems that that safenet card has a driver handling it at least. I'm pretty noobish still wrt the BSD's, though, so I'm not sure how helpful this is.
# dmesg -a Copyright (c) 1992-2009 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 7.2-RELEASE-p4 #0: Tue Oct 6 00:56:14 UTC 2009 sullrich@FreeBSD_7.2_pfSense_1.2.3_snaps.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc/src/sys/pfSense.7 Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Celeron(TM) CPU 1200MHz (1202.73-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x6b4 Stepping = 4 Features=0x383f9ff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,sep,mtrr,pge,mca,cmov,pat,pse36,mmx,fxsr,sse>real memory = 268435456 (256 MB) avail memory = 248655872 (237 MB) wlan: mac acl policy registered kbd1 at kbdmux0 ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) cryptosoft0: <software crypto="">on motherboard pcib0: <intel 82815="" (i815="" gmch)="" host="" to="" hub="" bridge="">pcibus 0 on motherboard pir0: <pci 11="" interrupt="" routing="" table:="" entries="">on motherboard $PIR: Using invalid BIOS IRQ 9 from 2.13.INTA for link 0x63 pci0: <pci bus="">on pcib0 agp0: <intel 82815="" (i815="" gmch)="" host="" to="" pci="" bridge="">on hostb0 pcib1: <pci-pci bridge="">at device 1.0 on pci0 pci1: <pci bus="">on pcib1 pcib2: <pcibios pci-pci="" bridge="">at device 30.0 on pci0 pci2: <pci bus="">on pcib2 safe0 mem 0xe7bfe000-0xe7bfffff irq 3 at device 6.0 on pci2 safe0: [ITHREAD] safe0: SafeNet SafeXcel-1141 rng des/3des aes md5 sha1 null</pci></pcibios></pci></pci-pci></intel></pci></pci></intel></software></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,sep,mtrr,pge,mca,cmov,pat,pse36,mmx,fxsr,sse>On another note, I just want to show off my hard disk mounting hack. With a dremel, drill, hammer, and an anvil, I made this sweet "cold-swap" bay for a spare laptop hard drive. The first blurry pic is the bottom of just the tray, and the second is the back of the tray locked into the tray's carrier (removed from the watchguard of course).
Important note, you can't see it in these pictures but I put a piece of clear plastic film under the hard drive to keep anything from shorting on the hard drive's controller board. Otherwise you would want to have washers under the drive at the mount points to create a gap (I didn't have washers of that size).
