Haiti emergency
-
pf would be the router, meaning it would if you wanted replace the "home" routers.
pf would seperate the different lans. i currently have a pf install seperating 4 LANs, its the router for all 4, all 4 have INternet access but only a 1 can access all LANs and 2 can access each other, the 4th can access Internet only.
-
What we need is for the LANs to be seperated (could combine the 2 'public' ones fairly easily, but we would want all of them to have Internet access. All these LANS come in on the same wire so my idea is to use the multiple IPs we have available from the iDirect a seperate Gateways for each of the areas. One NIC for each gateway in the server and a seperate router for each handing out DHCP for that LAN. We have enough decent 24 port switches available to handle any sort of complexity needed there.
The main advantages of the pfSense solution is that we could set it up immediately and it would give us an immediate handle on the traffic flow. We would initially use the small Linksys - Dlink routers we have. The load on each would be lessened so they would not heat up so badly, and if one does lock up it would only take out that segment. The only single point of failure would be the pfSense box and both the hardware and software are of the most reliable tye. Then when the Cisco routers arrive they can be programmed, tested and do a one minute swap for the home units.
-
LANs would still be seperated using pf with 1 public IP. its also easier to set up 1 WAN connection to 4 LAN connections and would be up the fastest.
set it up to have 1 WAN and 4 LANs set each connection to the type you want, enable them all set them up so that it does what you want (DHCP,DNS, etc) then just pass some rules on each interface so that they have Internet access only, but cant touch the pf box to mess with its settings, should be up and running in 15-30 min.
-
If you say so then I'll believe you. But I would still need help in configuring it as our time is critical. Would you be available to assist in that task tomorrow. I'm at home right now, supposed to be getting some rest. What version should I download (I think I already have 1.2.2, 1.2.3 and a Dec31 version of 2 Beta already on CD)
-
if its as critical as you say, dont use 2.0 its still in beta, use 1.2.3 its the current stable release.
what time tomorrow? I think you are 2 hours ahead of me. I am MST
-
I expect to get down there between 6:30 and 7 AM but road conditions and traffic are even more unpredictable than usual. We are on Eastern Standart Time at the moment
I'll be there all day
My Skpe ID is dfarquharson and I try to monitor that as often as possible as I'm also an amateur radio op
(just had about a 10 second shaking - but Idon't think it was over about a 2.5)
operator and am in contact with the emergency net controllers through skype more often than on the radio. -
get 1.2.3 its the most stable, will contact you via skype &/or your email tomorrow with a time frame that i will be availalbe (probably in the afternoon)
-
Hi! Mr. Farquharson,
I can tell you from my experience with pfSense it is the simplest and yet powerful routing/server setup available. I will say that if you have a box that isn't too old, then you will be set. I would recommend that you start off installing 1.2.2, from my experience it has been the most reliable overall, but have the 1.2.3 cdrom available just in case you have issues. You'll need enough network adapters for each of the separate networks on hand, just in case, wifi or ethernet. I don't know how the school campus network is setup, but if you happen to have any older linksys routers (they have a list of supported brand/model routers on their site) you might want to consider checking out www.dd-wrt.com and see if they can be flashed to use that firmware; it's more robust and reliable, and you can set them up as repeaters for where you don't have time to run wires. I'll try to monitor the forums and see if there is anyway that I can help too.
You should have quick success. I wish there was a way for me to come and help, but having a family and job makes it hard. I still remember being in your wife's 5th grade class.
My prayers are with you all. -
Would you have any use for a 24 and 48 port VLAN capable 10/100/100 switch? Two Cisco 1231ag access points? PCI NICs? Cables of any kind? Two 1u Dell 1750 servers (dual xeon 2.8, 2gb ram)? Anything else? I can put together a care package today and get it sent out today, although I have no idea how quick 'overnight' would actually be.
-
Let us know if you need any spare equipment you might need. I would be willing to overnight some items to you if needed. I have an Extra Linksys router/AP. I have an extra computer with linux and some extra HDD's for other computers.
-
Hey dfarquharson,
Did it work out OK? Would be nice to get some feedback on system used, obstacles, etc…if you're still around...
-
-