ADSLModem(bridged) and access modem from PFsense users.
-
Good afternoon!
The Adsl modem is translated in a "bridge" mode, connection type to the Internet - PPPoE
PFsense ver.2.0 with 2 network interfaces:
1-LAN (to a local network)
2-WAN and PPPoEAccess to the modem was required, the problem is already solved, but through WEB the interface it has not turned out.
Result: http://img30.imageshack.us/img30/4556/workingb.jpg
Whether it is possible to adjust similar adjustment without edit config.xml, but only through WEB the interface?–-------------------------
http://blog.translate.ru -
UP!
Another router.. PSsense 2.0 Beta1
3 network adapters:
vr0 - LAN
rl0 - WAN (ISP type PPPoE)
rl1 - Wifi interface (for Wifi AP)Modem in Bridge mode, and local ip - 192.168.10.1
to access modem - 4 interface 192.168.10.2, gateway, route, and 2 rule for LAN, 1 - default wan GW, 2- gw to 192.168.10.1my problem:
internet work only after push "save" in PFsense web site, on URL http://192.168.11.1/system.php
please help fix this problem=============================================================
Status: Interfaces
WAN interface (rl0)
Status up
PPPoE up
IP address 95.55.38.231
Subnet mask 255.255.255.255
Gateway 78.37.192.1
ISP DNS servers 213.158.7.2
212.48.193.37
LAN interface (vr0)
Status up
MAC address 00:19:5b:3e:3c:12
IP address 192.168.11.1
Subnet mask 255.255.255.0
Media 100baseTX <full-duplex>WIFI interface (rl1)
Status up
MAC address 00:80:48:42:8c:9b
IP address 192.168.12.1
Subnet mask 255.255.255.0
Media 100baseTX <full-duplex>PPPOELOCAL interface (rl0)
Status up
MAC address 00:e0:52:01:02:50
IP address 192.168.10.2
Subnet mask 255.255.255.0
Gateway 10 192.168.10.1
Media 100baseTX <full-duplex>==============================================================$ ifconfig -a
vr0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
options=2808 <vlan_mtu,wol_ucast,wol_magic>ether 00:19:5b:3e:3c:12
inet 192.168.11.1 netmask 0xffffff00 broadcast 192.168.11.255
inet6 fe80::219:5bff:fe3e:3c12%vr0 prefixlen 64 scopeid 0x1
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
rl0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
options=8 <vlan_mtu>ether 00:e0:52:01:02:50
inet6 fe80::2e0:52ff:fe01:250%rl0 prefixlen 64 scopeid 0x2
inet 192.168.10.2 netmask 0xffffff00 broadcast 192.168.10.255
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
rl1: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500
options=8 <vlan_mtu>ether 00:80:48:42:8c:9b
inet 192.168.12.1 netmask 0xffffff00 broadcast 192.168.12.255
inet6 fe80::280:48ff:fe42:8c9b%rl1 prefixlen 64 scopeid 0x3
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
lo0: flags=8049 <up,loopback,running,multicast>metric 0 mtu 16384
options=3 <rxcsum,txcsum>inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
inet 127.0.0.1 netmask 0xff000000
pfsync0: flags=0<> metric 0 mtu 1460
syncpeer: 224.0.0.240 maxupd: 128
pflog0: flags=100 <promisc>metric 0 mtu 33200
enc0: flags=0<> metric 0 mtu 1536
pppoe0: flags=88d1 <up,pointopoint,running,noarp,simplex,multicast>metric 0 mtu 1492
inet6 fe80::219:5bff:fe3e:3c12%pppoe0 prefixlen 64 scopeid 0x8
inet 95.55.38.231 –> 78.37.192.1 netmask 0xffffffff
=============================================================================</up,pointopoint,running,noarp,simplex,multicast></promisc></rxcsum,txcsum></up,loopback,running,multicast></full-duplex></vlan_mtu></up,broadcast,running,simplex,multicast></full-duplex></vlan_mtu></up,broadcast,running,simplex,multicast></full-duplex></vlan_mtu,wol_ucast,wol_magic></up,broadcast,running,simplex,multicast></full-duplex></full-duplex></full-duplex> -
The way you're accessing the modem is probably the easiest way to do it, add another interface.
When you say the Internet doesn't work until clicking Save on system.php, saving that page does a lot of things. What do you see before you click Save there, when the Internet doesn't work, if you go to Status > Interfaces?
-
@cmb:
The way you're accessing the modem is probably the easiest way to do it, add another interface.
Yes, fourth NIC - Solves this problem..
thanks :)When you say the Internet doesn't work until clicking Save on system.php, saving that page does a lot of things. What do you see before you click Save there, when the Internet doesn't work, if you go to Status > Interfaces?
Status: Interfaces
WAN interface (rl0)
Status up
PPPoE up
IP address 95.55.38.231
Subnet mask 255.255.255.255
Gateway 78.37.192.1
ISP DNS servers 213.158.7.2
212.48.193.37
LAN interface (vr0)
Status up
MAC address 00:19:5b:3e:3c:12
IP address 192.168.11.1
Subnet mask 255.255.255.0
Media 100baseTX <full-duplex>WIFI interface (rl1)
Status up
MAC address 00:80:48:42:8c:9b
IP address 192.168.12.1
Subnet mask 255.255.255.0
Media 100baseTX <full-duplex>PPPOELOCAL interface (rl0)
Status up
MAC address 00:e0:52:01:02:50
IP address 192.168.10.2
Subnet mask 255.255.255.0
Gateway 10 192.168.10.1
Media 100baseTX <full-duplex>====================================After click "Save" - the same.
I think a problem in the bridge and PPPoE.. Or the reason - "PPPOELOCAL interface (rl0)" is added not with Pfsense WEB.. otherwise - by change config.xml then configuration restoration..</full-duplex></full-duplex></full-duplex>