Igb drivers
-
That is about where I left off last night. Thanks for the link though! I was going to dig it out of a livecd.
Unfortunately when i tried to load the kernel module it said it was already there. Specifically it says:
modules_register: module pci/igb already already exists!
Module pci/igb failed to register: 17I'm going to pop in a live 7.2 cd in a few minutes when it finishes burning to see if the adapter works with it. I'll report back shortly.
-
Oh what fun.
The onboard CDrom drive wont boot a 7.2 or 8.0 disk, so I plugged in a USB CDrom and booted them up. The FreeBSD 8.0 disk auto-detects the NIC and the 7.2 does not, which is quite unfortunate. Is it reasonable to rip the igb drivers out of the pfSense kernel and load the 8.0 drivers with kldload? Or is there an 8.0 version of 1.2.3 still (I'm fairly sure there was at least at one point)? If so, is it stable and where can i get it?
What is the best way to edit the kernel w/ pfsense? I know that you removed the sysinstall utility…
-
No, there is no 1.2.3 version based on FreeBSD 8 (nor was there ever…) there were far too many changes for 8 to make that feasible.
If FreeBSD 8 sees your card, pfSense 2.0 should. If not, we may just need to add igb to the kernel config if it's not there already.
You can't mix and match modules between 7.x and 8.x, so that wouldn't work either.
-
Thanks for the reply again Jim,
It appears that the igb drivers in 7.2 don't work for the quad version of the NIC for some reason. The igb drivers on 8.0 do work. Intel offers the drivers on their site which in theory should work. I'll get around to that in a few hours to see if they'll install/work, but I think that there are igb drivers already there in the pfSense build, just they dont appear to work for my card. I suspect I will not be able to load the drivers though since the igb drivers are built into the kernel and I'm not sure how to edit the kernel in pfSense directly.
-
-
There are some test builds of 1.2.3 against FreeBSD 7.3 (or what will be 7.3), which may do the job for you. Not sure anyone has done a recent one though.
You can always try a custom build:
http://devwiki.pfsense.org/DevelopersBootStrapAndDevIso -
Rather than continue messing with this and trying to get the Intel Quad ET NIC to work with the 7.2 kernel, I called iXsystems and asked if they would swap me for an older chipset that either uses the em drivers or definitely works with the igb drivers in 7.2. They were great, very understanding and even apologetic that they used that card when they knew (sort of) that i was doing a pfSense build. A couple of their engineers called, listened to my concern (mostly that if I have to hack the kernel I cant just reinstall pfSense super quickly like I otherwise could) and then they offered to test their PT based quad NIC they had in stock with 7.2 to make sure it works by default and then overnight it assuming it does (to swap). It's nice to get competent people and great customer service… made me even more appreciative that I decided to purchase the massively overkill firewall from them.
-
If you can provide the output from # pciconf -l that I requested earlier it could prove useful for diagnosing possible future problems with this card.
-
pciconf -l printout here:
Sorry for the delay, been quite busy and this firewall needs a crapload of configuring so I can do the install.
-
pheleven: Thanks for the pciconf output. The four NICs are these devices:
none13@pci0:9:0:0: class=0x020000 card=0xa02b8086 chip=0x10e88086 rev=0x01 hdr=0x00
none14@pci0:9:0:1: class=0x020000 card=0xa02b8086 chip=0x10e88086 rev=0x01 hdr=0x00
none15@pci0:8:0:0: class=0x020000 card=0xa02b8086 chip=0x10e88086 rev=0x01 hdr=0x00
none16@pci0:8:0:1: class=0x020000 card=0xa02b8086 chip=0x10e88086 rev=0x01 hdr=0x00The device id 0x10e8 (upper half of what pciconf lists as the chip value) is identified in the FreeBSD 8.0 sources as E1000_DEV_ID_82576_QUAD_COPPER in source file e1000/e1000_hw.h which is referenced in e1000/if_igb.c in a table of IDs for supported devices. This entry is missing from the equivalent table in the FreeBSD 7.2 sources.
The FreeBSD 7.2 table includes these 82576 devices: E1000_DEV_ID_82576, E1000_DEV_ID_82576_FIBER, E1000_DEV_ID_82576_SERDES
The FreeBSD 8.0 table includes these 82576 devices: E1000_DEV_ID_82576, E1000_DEV_ID_82576_NS, E1000_DEV_ID_82576_FIBER, E1000_DEV_ID_82576_SERDES, E1000_DEV_ID_82576_SERDES_QUAD, E1000_DEV_ID_82576_QUAD_COPPER