No internet on lan
-
Do you have a default gateway set?!
route get defaultalso show the output of netstat -rn
-
route get default
[admin@pfSense.at.bepnet]/var/etc(11): route get default route to: default destination: default mask: default interface: vr0 flags: <up,done,static>recvpipe sendpipe ssthresh rtt,msec mtu weight expire 0 0 0 0 1500 1 0 [2.0-BETA1] [admin@pfSense.at.bepnet]/var/etc(12):</up,done,static>netstat -rn
[admin@pfSense.at.bepnet]/var/etc(12): netstat -rn Routing tables Internet: Destination Gateway Flags Refs Use Netif Expire default 10.0.0.1 US 0 11129 vr0 10.0.0.0/24 link#1 U 0 21724 vr0 10.0.0.1 link#1 UHS 0 40 lo0 10.0.0.243 link#2 UHS 0 0 lo0 87.164.245.122 link#8 UHS 0 0 lo0 127.0.0.1 link#7 UH 0 19 lo0 127.0.0.2 127.0.0.1 UHS 0 0 lo0 217.0.116.233 link#8 UH 0 0 pppoe0 Internet6: Destination Gateway Flags Netif Expire ::1 ::1 UH lo0 fe80::%vr0/64 link#1 U vr0 fe80::20d:b9ff:fe19:f31c%vr0 link#1 UHS lo0 fe80::%vr1/64 link#2 U vr1 fe80::20d:b9ff:fe19:f31d%vr1 link#2 UHS lo0 fe80::%lo0/64 link#7 U lo0 fe80::1%lo0 link#7 UHS lo0 fe80::%pppoe0/64 link#8 U pppoe0 fe80::20d:b9ff:fe19:f31c%pppoe0 link#8 UHS lo0 ff01:1::/32 fe80::20d:b9ff:fe19:f31c%vr0 U vr0 ff01:2::/32 fe80::20d:b9ff:fe19:f31d%vr1 U vr1 ff01:7::/32 ::1 U lo0 ff01:8::/32 fe80::20d:b9ff:fe19:f31c%pppoe0 U pppoe0 ff02::%vr0/32 fe80::20d:b9ff:fe19:f31c%vr0 U vr0 ff02::%vr1/32 fe80::20d:b9ff:fe19:f31d%vr1 U vr1 ff02::%lo0/32 ::1 U lo0 ff02::%pppoe0/32 fe80::20d:b9ff:fe19:f31c%pppoe0 U pppoe0 [2.0-BETA1] [admin@pfSense.at.bepnet]/var/etc(13): -
You have set default gateway on your wan
That is your problem. -
Shouldn't the default gateway set automatically because in mpd_wan.conf "set iface route default" is set. In former snapshots there was no need to set this by hand. How do i set the default gateway by hand?
the status page of the gateways shows following:WAN 217.0.116.233 217.0.116.233 Gathering data Interface wan Dynamic Gateway -
Ok, found it in the doc :) everything is working fine. Thanks a lot for your instant help.
-
Ok, found it in the doc :) everything is working fine. Thanks a lot for your instant help.
could u post the link to the doc which helped u?
-
-
Sorry for getting into this thread…
I am also fighting with this "problem" ... Had an older snapshot of 2.0beta on the box, did an online upgrade to the 19th march snapshot and now I have the exact problem as you have with the default gateway...
I have two PPoE-WAN-Uplinks (only one of the two is currently connected and has a public ip now), when I open the connected one and try to tick "use as default gateway", I get:"The following input errors were detected:
- The gateway address 213.191.64.183 does not lie within the chosen interface's subnet."
How did you resolve this?
Thanks a lot for your help!
Best regards,
Chris
-
I had same issue (cannot access internet) after upgrading from March 4th to March 19th nanobsd snap.
For everyone that cannot access internet try this: go to Interface > Wan and click save and then apply without changing anything. This should solve the problem.
My config XML from March 4th build looked like this:
<gateways><gateway_item><defaultgw>true</defaultgw></gateway_item> <gateway_item><gateway>dynamic</gateway> <descr>Interface wan dynamic gateway</descr> <name>GW_WAN</name> <interface>wan</interface></gateway_item></gateways>New XML from March 19th looks like this:
<gateways><gateway_item><gateway>dynamic</gateway> <descr>Interface wan dynamic gateway</descr> <name>GW_WAN</name> <interface>wan</interface></gateway_item></gateways>PHP code from March 19th that sets default route in mpd config file:
$setdefaultgw = false; $founddefaultgw = false; if (is_array($config['gateways']['gateway_item'])) { foreach($config['gateways']['gateway_item'] as $gateway) { if($interface == $gateway['interface'] && isset($gateway['defaultgw'])) { $setdefaultgw = true; break; } else if (isset($gateway['defaultgw'])) { $founddefaultgw = true; break; } } } if (($interface == "wan" && $founddefaultgw == false) || $setdefaultgw == true) $mpdconf .= << <eod<br>set iface route default EOD;</eod<br>When this code uses old XML config (which I think happens after upgrade) it will not add default route because $setdefaultgw will be false and $founddefaultgw will be true.
In the new XML configuration this is missing:<gateway_item><defaultgw>true</defaultgw></gateway_item>so $founddefaultgw will be false and default route will be set in the mpd config file.
If I go to System > Routing and edit GW_WAN 'Default Gateway' checkbox is not checked so that might be a bug.
-
Thanks for your reply and your information! :-)
Best regards,
Chris