Problem with fw rules
-
Make a networks(s) alias that has all the networks that you want to deny access to and use that alias in the rule in place of the interface group you now have there.
-
Hi,
I have the following VLANs setup on my pfsense box running v2;
VLAN10 - 172.16.10.0/24 - Wired connection (with internet access)
VLAN20 - 172.16.20.0/24 - Wireless connection (with internet access)
VLAN254 - 172.16.254.0/24 - Protected Servers (no internet access)
VLAN400 - 172.16.1.0/24 - Management; fw, switches and aps are on this vlan (no internet access)
See attachment for the rules of each vlan.The problem I am having is that VLAN254 speaks with ALL vlans, when I only want it to speak with VLAN10. As far as I can see I have all the rules correct.
I even tried deleting the V254 interface and vlan and recreated it with no fw rules (no rules should by default mean DENY All ,right?). Still able to reach it from all other vlans.
There is no trouble with the other vlans, as I can disable rule for allowing v10 to speak to v20 and that will work after a few seconds!Is there something VERY obvious that I am missing, or could it be a bug in pfsense or the switch?
Hoping for some quick replies :)
Brgds,
You are allowing Vlan10 access your vlan254 from any gateway and this might be route from other vlans to access your vlan254 via vlan10? Just an bad guess… Try to to limit vlan10 access to your vlan254 only from gateway 172.16.10.1 . It's hard to guess whats really happening with out any logs, but trace route should tell a lot... Other vice you must deny access to vlan254 from vlan 20 and 400.
-
His problem is most likely the interface group, afaik it's not intended to be used that way. A networks(s) alias should make his setup work.
-
Post the contents of rules.debug from status.php while that interface group is in place.
-
Here it is;
Public IPs consored with 127.0.0.1#System aliases loopback = "{ lo0 }" WAN = "{ pppoe1 }" VLAN400 = "{ re0_vlan400 }" VLAN10 = "{ re0_vlan10 }" VLAN20 = "{ re0_vlan20 }" VLAN254 = "{ re0_vlan254 }" OpenVPN = "{ openvpn }" vlanInternet = "{ vlanInternet }" #SSH Lockout Table table <sshlockout>persist #Snort2C table table <snort2c>table <virusprot># User Aliases table <vlan_internet>{ 172.16.10.0/24 172.16.20.0/24 } vlan_internet = "<vlan_internet>" # Gateways GWwan = " route-to ( pppoe1 127.0.0.1 ) " set loginterface pppoe1 set loginterface re0_vlan400 set loginterface re0_vlan10 set loginterface re0_vlan20 set loginterface re0_vlan254 set optimization normal set limit states 298000 set skip on pfsync0 scrub in on $WAN all max-mss 1460 fragment reassemble scrub in on $VLAN400 all max-mss 1460 fragment reassemble scrub in on $VLAN10 all max-mss 1460 fragment reassemble scrub in on $VLAN20 all max-mss 1460 fragment reassemble scrub in on $VLAN254 all max-mss 1460 fragment reassemble nat-anchor "natearly/*" nat-anchor "natrules/*" # Outbound NAT rules # Subnets to NAT table <tonatsubnets>{ 172.16.1.0/24 172.16.10.0/24 172.16.20.0/24 172.16.254.0/24 172.1.1.0/27 } nat on $WAN from <tonatsubnets>port 500 to any port 500 -> 127.0.0.1/32 port 500 nat on $WAN from <tonatsubnets>port 5060 to any port 5060 -> 127.0.0.1/32 port 5060 nat on $WAN from <tonatsubnets>to any -> 127.0.0.1/32 port 1024:65535 # Load balancing anchor rdr-anchor "relayd/*" # TFTP proxy rdr-anchor "tftp-proxy/*" table <direct_networks>{ 127.0.0.1/32 172.16.1.0/24 172.16.10.0/24 172.16.20.0/24 172.16.254.0/24 } # NAT Inbound Redirects rdr on pppoe1 proto { tcp udp } from any to 127.0.0.1 port 80 -> 172.16.10.20 # UPnPd rdr anchor rdr-anchor "miniupnpd" anchor "relayd/*" anchor "firewallrules" #--------------------------------------------------------------------------- # default deny rules #--------------------------------------------------------------------------- block in log all label "Default deny rule" block out log all label "Default deny rule" # We use the mighty pf, we cannot be fooled. block quick proto { tcp, udp } from any port = 0 to any block quick proto { tcp, udp } from any to any port = 0 # Block all IPv6 block in quick inet6 all block out quick inet6 all # snort2c block quick from <snort2c>to any label "Block snort2c hosts" block quick from any to <snort2c>label "Block snort2c hosts" # package manager early specific hook anchor "packageearly" # carp anchor "carp" # SSH lockout block in log quick proto tcp from <sshlockout>to any port 22 label "sshlockout" block in quick from <virusprot>to any label "virusprot overload table" table <bogons>persist file "/etc/bogons" # block bogon networks # http://www.cymru.com/Documents/bogon-bn-nonagg.txt anchor "wanbogons" block in log quick on $WAN from <bogons>to any label "block bogon networks from WAN" antispoof for pppoe1 # block anything from private networks on interfaces with the option set antispoof for $WAN block in log quick on $WAN from 10.0.0.0/8 to any label "block private networks from wan block 10/8" block in log quick on $WAN from 127.0.0.0/8 to any label "block private networks from wan block 127/8" block in log quick on $WAN from 172.16.0.0/12 to any label "block private networks from wan block 172.16/12" block in log quick on $WAN from 192.168.0.0/16 to any label "block private networks from wan block 192.168/16" antispoof for re0_vlan400 antispoof for re0_vlan10 antispoof for re0_vlan20 antispoof for re0_vlan254 anchor "spoofing" # loopback anchor "loopback" pass in on $loopback all label "pass loopback" pass out on $loopback all label "pass loopback" anchor "firewallout" # let out anything from the firewall host itself and decrypted IPsec traffic pass out all keep state allow-opts label "let out anything from firewall host itself" pass out route-to ( pppoe1 127.0.0.1 ) from 127.0.0.1 to !127.0.0.1/32 keep state allow-opts label "let out anything from firewall host itself" # make sure the user cannot lock himself out of the webConfigurator or SSH anchor "anti-lockout" pass in quick on re0_vlan400 from any to (re0_vlan400) keep state label "anti-lockout rule" # NAT Reflection rules # User-defined rules follow pass in quick on $WAN reply-to ( pppoe1 127.0.0.1 ) proto tcp from 127.0.0.1 to 127.0.0.1 port 443 flags S/SA keep state label "USER_RULE" pass in quick on $WAN reply-to ( pppoe1 127.0.0.1 ) proto tcp from 127.0.0.1 to 127.0.0.1 port 443 flags S/SA keep state label "USER_RULE" pass in quick on $WAN reply-to ( pppoe1 127.0.0.1 ) proto tcp from 127.0.0.1 to 127.0.0.1 port 443 flags S/SA keep state label "USER_RULE" pass in quick on $WAN reply-to ( pppoe1 127.0.0.1 ) proto { tcp udp } from any to any port 1194 keep state label "USER_RULE" pass in quick on $WAN reply-to ( pppoe1 127.0.0.1 ) proto { tcp udp } from any to 172.16.10.20 label "USER_RULE: NAT " pass in quick on $vlanInternet from any to ! $vlan_internet keep state label "USER_RULE" pass in quick on $VLAN254 from 172.16.254.1/24 to 172.16.10.1/24 keep state label "USER_RULE" block in log quick on $VLAN254 from any to any label "USER_RULE" pass in quick on $VLAN20 from 172.16.20.1/24 to 172.16.10.1/24 keep state label "USER_RULE" block in log quick on $VLAN20 from any to any label "USER_RULE" pass in quick on $VLAN10 from 172.16.10.1/24 to 172.16.1.0/24 keep state label "USER_RULE" pass in quick on $VLAN10 from 172.16.10.1/24 to 172.16.20.1/24 keep state label "USER_RULE" block in log quick on $VLAN10 from any to any label "USER_RULE" pass in log quick on $OpenVPN from any to any keep state label "USER_RULE" pass in quick on $VLAN400 from 172.16.1.0/24 to 172.16.1.0/24 keep state label "USER_RULE" pass in quick on $VLAN400 from 172.16.1.0/24 to 172.16.10.1/24 keep state label "USER_RULE" pass in quick on $VLAN400 from 172.16.1.0/24 to 172.16.20.1/24 keep state label "USER_RULE" block in log quick on $VLAN400 from any to any label "USER_RULE" # VPN Rules # package manager late specific hook anchor "packagelate" anchor "tftp-proxy/*" anchor "limitingesr" # uPnPd anchor "miniupnpd"</bogons></bogons></virusprot></sshlockout></snort2c></snort2c></direct_networks></tonatsubnets></tonatsubnets></tonatsubnets></tonatsubnets></vlan_internet></vlan_internet></virusprot></snort2c></sshlockout> -
Ruleset is fine. what output does:
ifconfig -g vlanInternet
give you?
-
This:
$ ifconfig -g vlanInternet re0_vlan10 re0_vlan20 -
The config is fine then. Reading your first post again, maybe you're misunderstanding how things work. If there are no rules on VLAN250, then VLAN250 can't talk out to anything. But if other interfaces have rules allowing them to talk to VLAN250, that will work. Traffic is filtered on the interface (or interface group) where it's initiated.
-
Hello again,
I don't think I am misunderstanding. Right now I have no rules on V254, but all traffic except WAN is getting through to that VLAN. If I disable the rule in vlanInternet however no traffic is passed to V254
-
Right now I have no rules on V254, but all traffic except WAN is getting through to that VLAN. If I disable the rule in vlanInternet however no traffic is passed to V254
Exactly my point - that traffic isn't initiated on VLAN254. Traffic is only filtered on the interface where it's initiated. Everything is functioning as it should be from that description. If you don't want the other interfaces to talk to VLAN254, block them on their interface, the source interface of the traffic, not the destination one.