Watchguard Firebox X Peak platform

stephenw10

The 875p chipset supports up to 4GB in 4 dimm slots. However the X-peak motherboard only has two slots (although it has space for 4 if you're feeling brave with a soldering iron!) so I would say 2GB.
Reference: here.
Steve

Xfinity

Thanks for the info, any good pointers in ram-modules that work as well? ;)

stephenw10

Hmm,
Well first off I've not tried any other DIMMs in my firebox. To be honest 512MB seems more than enough for my needs. You could look at Intels guide for their desktop 875p board here . It doesn't mention any specific manufacturers though. Otherwise try Googling for 875p motherboards from other manufacturers who may have lists of approved DIMMs.
Do you have a firebox then?

Steve

Xfinity

Thanks for all information regarding the memory on this thing, going to check ebay in a few and see what I can find ;)…

stephenw10

No problem! ;D
Keep us updated with what works and what doesn't.

Steve

stephenw10

The Advantech AIMB-X3 motherboard has by default only one usb connection, the front mounted usb port. It has hardware, however, to support at least 4 ports and possibly 6 or 8! The Intel FWE6300ESB chip haas a 4 port controller and the I/O chip has an additional controller. The usbdevs command shows 6 ports.

There are unpopulated headers on the motherboard for three additonal ports. They are just behind the existing USB port and labeled CN25 and CN27. In order to get these to function some soldering skills are required along with some bravery!

The 5V power for the USB ports is supplied via a fuse and the data connections are routed via a common mode filtering choke. Only the existing port has a choke and fuse in place, the others are unpopulated. Fortunately the existing fuse, Fuse 3 (FS3, 1.1A), supplies both the front port and CN27 so to get just one internal port we don't have to add any fuses. The filtering chokes are layed out in a line on the pcb labeled CK1-CK4. Only CK4 is present. I purchased the smalled choke I could easily find but it was still far too big (3x2mm!) as a test I simply used some wire instead of the choke and so far it seems to function just fine. It could be that the filtering is overkill or that I'm not really stressing it enough to show up any problems.

Warning: some very bad soldering is in this picture! :P

I don't have any surface mount reworking tools so I had to use the smallest soldering iron I could find which was still far too large. Despite that I had a huge problem getting a pin into the GND connection on the header. The ground plane on the PCB just sinks all the heat. In the end I had to drill it out with a very small drill bit! :o

The internal USB connection opens up some exiting possibilties: 3g modem, flash drive, etc.

StuartW

Hi

I ran the commands up to here:

@stephenw10:

/etc/rc.conf_mount_rw
Because I'm using an embedded image I first mount it read-write.
pkg_add -r mbmon
Add the mbmmon package.
 /etc/rc.conf_mount_ro
Remount the CF card read only.

But when I run this bit:
@stephenw10:

./mbmon -d
ioctl(smb0:open): No such file or directory
SMBus[Intel8XX(ICH/ICH2/ICH3/ICH4/ICH5/ICH6)] found, but No HWM available on it!!
Using ISA-IO access method!!
* Winbond Chip W83627HF/THF/THF-A found.

All I get is:


# ./mbmon
./mbmon: Command not found.
#

Any suggestion as to what I might be doing wrong?

Thanks

Stuart

stephenw10

You have to call it from the right directory or use the absolute path:

/usr/local/bin/mbmon -I

The -I causes mbmon to use only the ISA bus sensors, which are the only ones available on the Firebox under FreeBSD.

Steve

StuartW

@stephenw10:

/usr/local/bin/mbmon -I

That did it! Thanks…

# /usr/local/bin/mbmon

Temp.= 66.0, 127.0, 85.0; Rot.=    0, 4440,    0
Vcore = 1.46, 3.39; Volt. = 3.31, 4.87, 11.80,  -3.06, -6.14

Nice and warm ;)

stephenw10

Ooo, that is warm. :o
You only seem to have one fan?

Steve

StuartW

Yeah, this is an x700 firebox. Has one fan direct on the CPU, then three tiny fans on the back panel. Having in the loft probably doesn't help either….

stephenw10

I just got a hard drive caddy that fits the X peak perfectly.
It's nice and snug in the plastic rails and has a little handle on the back to pull it out without opening the case. ;D

It's from a laptop, an ECS-320. In the UK it was sold rebadged as an Advent 7081 and also Patriot 2005.
Possible models that used the same caddy are Advent 7086, 7094, and ECS 321. Make sure you get the adapter with it. ;)

Steve

shinyfoil

Hey!

Thanks so much for your great work on these boxes. I just got an x8000 off fleabay and tossed in your BIOS checking image. Looks like I've got the same version as you…I just put in an order for some new fans for this thing (it literally sounds like a small jet starting up) which will hopefully quiet it down.

stephenw10

While doing some throughput testing on my other Firebox I hit the limits of the my X-peak.
I'm using TTCP to measure network throughput/bandwidth. It's a useful tool since it has windows and freebsd versions and they're compatible so you can have any box at either end of your test setup.
I have used my X-Peak as the receive end connected to one of the gigabit ports. I found I was maxing out my one section of gigabit network at around 360Mbps. I had blamed that on bad network cards and a long length of cat5e carelessly routed past mains cable (who knew when I installed it 10 years ago!).
However some testing showed that the cpu was pinned at 100%. Bear in mind that this box is receiving the data only so actual throughput would be lower.

One interface 365Mbps in 19Mbps out = 100% cpu.

However! :P I am using an underclocked replacement cpu running at 1.2GHz. Scaling that may give 850Mbps with the original 2.8GHz cpu, assuming nothing else is limiting peformance. I might have to try that pin mod after all.

Steve

mmiller

Does anyone have a source for the WG FIrebox X8000 hard drive caddy in the United States?

neotec_de

@Steve:

First of all… Thanks for the great infos till now.
It works great for me at my X8510e-F --> LCD/LED driver works like a charme.
At which time you plan a watchguard package for 2.0?

But now....
I have a problem to get access to the bios (X8000) --> same biosversion like your box.
I flashed the bios with the help of your CF-image and of course with the /cc switch :)
biosid.com says it's ok --> your new "Steves" bios-messages shows up.
But still no boot info shows up at start in the consolewindow.

There are still any secret steps to show it up? ???

BTW: The J3 connector on the PSU-Board is for a 12V fan.

Alex

stephenw10

@neotec_de:

At which time you plan a watchguard package for 2.0?

When I learn some proper programming skills. ::)

@neotec_de:

But still no boot info shows up at start in the consolewindow.

There are still any secret steps to show it up? ???

I take it you're not using a keyboard on the ps/2 connector?

The 'console redirect' function in the bios is very buggy.
To see anything using just the serial console you have to press keys. I don't know why, it should just show the POST but it doesn't.
Start pressing tab and enter as soon as you power on the box and keep pressing them until you see something.
If you really want to change something in the bios you'll need to hook up a keyboard directly.

How do you know that about J3?

Steve

neotec_de

Ok. I will give it a try tomorrow.

The greenwire is marked with "ON/OFF" –> have a look at the atx-power-connector.
The PSU is a standard one, but without a case.
And so imho is it the connector for the case fan. ;)
It delivers 12V and GROUND.

Alex

neotec_de

It works! :)

Phoenix - AwardBIOS v6.00PG, An Energy Star Ally
Copyright (C) 1984-2003, Phoenix Technologies, LTD

Modified by Steve for 115200 console.

Main Processor : Intel(R) Pentium(R) 4 CPU 2.80GHz(133x21.0)
Memory Testing :  524288K OK
CPU Brand Name : Intel(R) Pentium(R) 4 CPU 2.80GHz

  Memory Frequency For DDR333  (Dual Channel Mode Enabled)
  Primary Master : SanDisk SDCFB-128 Vdi 1.24
   Primary Slave : None
Secondary Master : None
 Secondary Slave : FUJITSU MHT2060BH 0000104A

                           Phoenix Technologies, LTD
                             System Configurations
+==============================================================================+
| CPU Type   : Intel(R) Pentium(R) 4 CPU  Base Memory       :    640K          |
| CPU ID/ucod: 0F29/17                    Extended Memory   : 523264K          |
| CPU Clock  : 2.80GHz                    Cache Memory      :    512K          |
|------------------------------------------------------------------------------|
| Diskette Drive A  : None                Display Type      : MONO             |
| Diskette Drive B  : None                Serial Port(s)    : 3F8 2F8          |
| Pri. Master Disk  : LRG,PIO 4,  128MB   Parallel Port(s)  : 378              |
| Pri. Slave  Disk  : None                DDR at Bank(s)    : 0 2              |
| Sec. Master Disk  : None                                                     |
| Sec. Slave  Disk  : LRG,ATA 100,59599MB                                      |
+==============================================================================+

PCI device listing ...
Bus No. Device No. Func No. Vendor/Device Class Device Class               IRQ
--------------------------------------------------------------------------------
   0       29         0     8086   25A9   0C03  USB 1.0/1.1 UHCI Cntrlr     10
   0       29         1     8086   25AA   0C03  USB 1.0/1.1 UHCI Cntrlr      5
   0       29         4     8086   25AB   0880  Base Sys. Peripherals       NA
   0       29         5     8086   25AC   0800  I/O(X) APIC Cntrlr          NA
   0       31         2     8086   25A3   0101  IDE CntrlrCI Cntrlr         14
   0       31         3     8086   25A4   0C05  SMBus Cntrlr                12
   2        1         0     8086   1075   0200  Network Cntrlr              11
   3       13         0     16AE   000A   1000  En/Decryption Cntrlr         9
   3       14         0     8086   1079   0200  Network Cntrlr               9
   3       14         1     8086   1079   0200  Network Cntrlr               9
   4        9         0     8086   1209   0200  Network Cntrlr               5
   4       10         0     8086   1209   0200  Network Cntrlr              11
   4       11         0     8086   1209   0200  Network Cntrlr              12
   4       12         0     8086   1209   0200  Network Cntrlr              10
   4       13         0     8086   1209   0200  Network Cntrlr               5
   4       14         0     8086   1209   0200  Network Cntrlr              11
   4       15         0     8086   1209   0200  Network Cntrlr              12

Updating ESCD ... Success
Building DMI Pool ............................ Success

Additionaly I've soldered in the two SATA-Ports.
Both of them are working!
The Sec. Slave Disk from the postscreen is an SATA 2,5" HDD.

Alex

X8000_SATA.JPG_thumb

stephenw10

Nice work! :)

Does it boot from SATA? Did you have to solder any other components or just the connectors?

Looking good. ;D

Steve