Country Block

deltaend

tommyboy180, when Traffic Shaping and country block are installed on the same pfsense firewall, it causes a 404 to be displayed when you attempt to view the traffic shaping panel and Country Block fails to run with an invalid syntax error.

tommyboy180

@deltaend:

tommyboy180, when Traffic Shaping and country block are installed on the same pfsense firewall, it causes a 404 to be displayed when you attempt to view the traffic shaping panel and Country Block fails to run with an invalid syntax error.

I found a quick fix and will be pushing an update soon.

deltaend

I love you.

jsmwalker

Hi there,

Great package, just wanted to check which interfaces this creates the rules on?

Cheers

J

Supermule

Heyy Tommy….:) Was I spot on or what??? :D

See ya ;)

tommyboy180

@jsmwalker:

Hi there,

Great package, just wanted to check which interfaces this creates the rules on?

Cheers

J

This affects all interfaces.

jward

Hi Tommy, this is a really great package - thanks for putting time into developing it! ;D

If possible in some future release it would be great to be able to apply the country block settings per interface, even better if it could be down to the Virtual IP level. I'm sure like many others, we have various services running on different Virtual IPs, some need to be open to the world, but others could be very heavily limited to 1 or 2 countries so being able to block countries down to the Virtual IP level would really help.

Thanks again,
Jon

jroberts31xray

(if im posting in the wrong area just let me know)

Thanks Tommy for a great package, i am a huge fan and it and deployed this on every firewall i build…....ok now of for the question ;D

i have a Dell power edge 1850 dual xeons 3.0's and 2g ram and about 35gb of disk space running 1.2.3. Release. (Mind you this is first time i have seen this) We had the original config for this on a "Alix" board and just moved the config file over to the larger servers on a fresh install.

Issue: Committing the country's to the block list is fine however when i Enable Country Block i receive the following error:

Current Status = NOT running
/tmp/rules.debug:44: syntax error
You are blocking 0 Networks

if anyone in the community has any ideas please let me know....Thanks again.....

Image Below.

tommyboy180

@jroberts31xray:

(if im posting in the wrong area just let me know)

Thanks Tommy for a great package, i am a huge fan and it and deployed this on every firewall i build…....ok now of for the question ;D

i have a Dell power edge 1850 dual xeons 3.0's and 2g ram and about 35gb of disk space running 1.2.3. Release. (Mind you this is first time i have seen this) We had the original config for this on a "Alix" board and just moved the config file over to the larger servers on a fresh install.

Issue: Committing the country's to the block list is fine however when i Enable Country Block i receive the following error:

Current Status = NOT running
/tmp/rules.debug:44: syntax error
You are blocking 0 Networks

if anyone in the community has any ideas please let me know....Thanks again.....

Image Below.

Just to make sure do you have the latest version of countryblock installed?
Also what other pages are you running? Traffic shaping?

jroberts31xray

Version 0.1.4 on the C.B. and i am not running shaping, packages listed below: btw we are running the FW transparent.

Package Name Category Package Version
Country Block Firewall 0.1.4
Dashboard System 0.8.8
IP-Blocklist Firewall 0.2.2

thanks for the FAST reply. ;)

Supermule

Then its not a firewall any more and doesnt do any blocking….;)

jroberts31xray

We got it…thanks again Tommy, great package.

it was a bad config file......Thanks

tommyboy180

@jroberts31xray:

We got it…thanks again Tommy, great package.

it was a bad config file......Thanks

Thank you for your support!

jroberts31xray

Yup….NP the config was from an embedded alix board and did not work when imported to a full hardware install..........from what i am told its a "Known" issue. Your package is awesome and it does the Job 100%! thanks again. The folks here at Bluegrassnet appreciate it!

kilthro

i wanted to say thanks for this package!!! its fantastic. This package is what got me introduced to pfsense since i needed something to block all of china and korea from my web servers. I have it added to cron to make sure it runs all the time as well.

I did have a question, is there any way to have this package to show up on the services screen?

I have that widget added to my main log in (dashboard) page on 2.0 and it would be good to see right there if it is running or not.

Just thought I would ask.

tommyboy180

@kilthro:

i wanted to say thanks for this package!!! its fantastic. This package is what got me introduced to pfsense since i needed something to block all of china and korea from my web servers. I have it added to cron to make sure it runs all the time as well.

I did have a question, is there any way to have this package to show up on the services screen?

I have that widget added to my main log in (dashboard) page on 2.0 and it would be good to see right there if it is running or not.

Just thought I would ask.

It's not really a service that is running to block the countries, so having this package show up in the services will not be possible. The way it works is by basically injecting a couple lines of deny rules to your fw config so being able to track the current status of the package will have to be done via other means. If you know php I would love the extra help!
There are still many changes to come and I haven't forgotten about that update deltaend!
I do appreciate the support, so thank you!

tci

I have a wierd problem. I selected 12 countries, all of spammers list + Barbados + Italy. Whenever I return to the list once saved, Barbados is never selected but it is being blocked.
Status says Currently 12 of 246 selected.

Using Chrome. Anything i'm doing wrong or is it a bug?

tommyboy180

Version 1.5 Released

Changes:

Added embedded compatibility.
Verified working with traffic shaping settings
Added interface choices - just for you jward!
Fixed bug with country Barbados - Thank you tci!

Warning: You need to select the interfaces that this will apply to before you run it. I Highly Recommend selecting all interfaces.
If you run into a problems let me know.
deltaend: I fixed the 404 problem and tested pfsense w/ traffic shaping. I was able to have it working w/ traffic shaping enabled so let me know if you run into any problems.

Thank you all for your patience with updates.

1.5.jpg
1.5.jpg_thumb

jward

Thanks Tommy, will take a look.

Supermule

Aint this a wrong path for the new 0.1.5 edition of Country block??

/usr/local/etc/rc.d/countryblock.sh

I use this…

/usr/local/www/packages/countryblock/countryblock.sh

@darklogic:

Thanks for all your help. :)

I did your suggestion with the uncheck Bogon and added the cron package and applied the command you specified. All seems to be working well with the Country Block package now. I rebooted my firewall and all came up ok. I did notice I could access some Chinese websites with extensions of .cn

Does the Country Block work for both IP's and DNS naming or just IP?

A On the cron job I made the new job entry with this criteria and maybe you have some suggestions or minor tweaks to it.

Cron Job:

Minute: 0
Hour: *
Mday: *
Month: *
Wday: *
Who: root
Command: /usr/local/etc/rc.d/countryblock.sh