Squid can't work
-
If you want to confirm it for yourself, you could try either one of these updates that I built without the patch in question.
amd64 - http://pingle.org/files/pfSense-Full-Update-2.0-BETA4-20101212-2328.tgz
i386 - http://pingle.org/files/pfSense-Full-Update-2.0-BETA4-20101214-1319.tgz
Use at your own risk, YMMV, etc. :-)
-
Did that test with the i386-image:
First updated via the "normal" update to snap from Dec, 14. Enabled squid transparent and tried to surf to a site: Nothing except a timeout. Disabled sq2uid transparent, site loads.
ok.
Now installed your snap from post above and enabled squid transparent. Site loads fine. (tested with another site to eliminate caches.)
Its definitly the change which causes that malfunction of squid.
-
I try to update with the file : 386 - http://pingle.org/files/pfSense-Full-Update-2.0-BETA4-20101214-1319.tgz
But the squid with transparent enable browsing can not run normally.
and disable transparent when browsing can work well ..So, where is his fault?
:o
-
reply #6, page 1 explains the thing…
-
Thanks you
and Thank jimp, on page 1 says checks, allow interface:)
-
Just want to let you know:
This fix works for me on snapshot Dec 14 with squid2 transparent mode:
i386 - http://pingle.org/files/pfSense-Full-Update-2.0-BETA4-20101214-1319.tgz -
Hi Jimp - confirm the i386 build without the patch works in transparent mode. Upgraded one box from Dec 6 build.
However the broken console display problem is back. :-\
We were using Dec 6 build where everything works fine - still have that version installed on another box.
If you want to confirm it for yourself, you could try either one of these updates that I built without the patch in question.
amd64 - http://pingle.org/files/pfSense-Full-Update-2.0-BETA4-20101212-2328.tgz
i386 - http://pingle.org/files/pfSense-Full-Update-2.0-BETA4-20101214-1319.tgz
Use at your own risk, YMMV, etc. :-)
-
However the broken console display problem is back. :-\
Do you have a separate thread for that? There has never been a "broken" console display problem that I'm aware of. The console menu was redesigned into a two column format but that's the only change. If that's not it, start a new thread with screenshots or some other reproduction of the "corruption" so it can be looked into on its own.
-
O.K. I've gone ahead and opened a new thread for this problem.
However the broken console display problem is back. :-\
Do you have a separate thread for that? There has never been a "broken" console display problem that I'm aware of. The console menu was redesigned into a two column format but that's the only change. If that's not it, start a new thread with screenshots or some other reproduction of the "corruption" so it can be looked into on its own.
-
I disabled the patch in the repo and have a new snapshot building now. The next new snapshot dated after this update should be OK.
-
Tried tonight's build Dec 15 and Squid still broken.
Reverted to your custom build of yesterday:
http://pingle.org/files/pfSense-Full-Update-2.0-BETA4-20101214-1319.tgz
Squid works fine.
I disabled the patch in the repo and have a new snapshot building now. The next new snapshot dated after this update should be OK.
-
There isn't a "tonight" build of Dec 15 for i386 yet, it hasn't finished. There is one from 7-ish AM this morning, but that wouldn't have had the fix. (The build of mine you quoted is i386, so I presume you weren't using amd64, there is a fixed build up for that now)
It's still working on NanoBSD images, it'll probably be a while yet before it's uploaded, maybe a couple hours.
-
is this the lastest build today "pfSense-2.0-BETA4-20101215-1831.iso.gz" that make squid work?
cos i want to use it to make a freash install to new system.
-
The latest amd64 build is good, I just tested it. Upgraded my VM and installed squid, and I was able to connect from behind it, confirmed it was doing a transparent redirect (caught it in the access log).
-
sounds good, i am downloading now hope this will work find. I am 1st time try PFsense, from what i read at the website it is very powerfull software router and easy to use.
-
Hi,
just a shot question:
I applied this patch on Dec 14 snapshot:
i386 - http://pingle.org/files/pfSense-Full-Update-2.0-BETA4-20101214-1319.tgzan squid2 works now on my machine.
Today I updated to 2.0-BETA4 (i386) built on Wed Dec 15 20:50:23 EST 2010 and squid2 still works.
Is this because of the patch I applied yesterday or is this patch included in the new snapshot or is this patch "universal" to alle new snapshots ?thx.
-
The firmware files that I built had a patch removed, and now that same patch is removed from the "real" snapshot firmware files.
People who upgrade to a current snapshot (even those who never touched the firmware files I posted) should all be working now.
-
I can confirm that the "real" snapshot pfSense-Full-Update-2.0-BETA4-20101216-0237.tgz dated 16-Dec-2010 05:02 76M has now been fixed to address the broken Squid :)
The annoying "beep" when logging on via the Web GUI is still there.
May just unplug the speaker if this stays on as a "Feature" :P
I am getting to like Pfsense - any idea when the 2.0 version of the book will be out?
The firmware files that I built had a patch removed, and now that same patch is removed from the "real" snapshot firmware files.
People who upgrade to a current snapshot (even those who never touched the firmware files I posted) should all be working now.
-
The 2.0 book won't be out for a while yet, we haven't really even started on it. It's very hard to document a moving target so we can't do any real serious work until it's released or much later in the RC phase.
-
Thanks for your feedback, jimp and mromero
Even thanks for participate on writing this book for version 1.2.3 of pfSense.
I bought it and it will help me many basic things, too, whatever it is pfSense 1.2.3 or 2.0beta–--EDIT----
If I'm right, in the "package list" I could read, that lightsquid needs squid installed before. Im not sure, if I could install lightsquid without squid installed - nevertherless if this makes sense - but after updating the box to a new firmware, it first installs lightsquid and then squid.
If it works - and it does actually, it's not a problem for me but perhaps there is a reason I don't understand :)
