Еще раз о ipcad+squid+lightsquid
-
скорей всего pfsense не может резолвить имена - не указан dns.
-
Конечный URL (например имя скачанного файла) без squid не будет видно все равно. Да и сайты тоже толком не покажет, ибо их куча может быть на одном IP.
-
-
Да и сайты тоже толком не покажет, ибо их куча может быть на одном IP.
В этом и загвоздка.
Может можно чем-то другим "поиметь" статистику посещаемых ресурсов без проксирования? -
-
Da prosto otredaktiruy svoyu statyu I postav' pervoj strokoj:
Avtor: … -
просьба не кидаться тапками, переделал как умел скрипт, в результате через dig -x пытаемся отресолвить адреса куда ходили, если не ресолвиться - остается ip,
плюс к этому хочу заметить, что идущий в поставке 1.2.3 lightsquid 1.7.1 косячит когда данные о клиентах только адреса и куда ходили - тоже адреса - путает адресата и адрес куда ходили. решил ручной заменой lightsquid на 1.8 -
При запуске скрипта:
./tolog.sh: line 13: syntax error near unexpected token
}' ./tolog.sh: line 13:}' -
не знаю что Вам сказать, скрипт с рабочего сервера, вот что в итоге получается
-
::)
Я его не на PfSense тестил -
тогда смотрите на свой bash и пилите под себя
-
А можете скрипт в .tar запаковать?
Может я криво .тхт "копипостю"
Потому как, bash "просит" некоторые директивы заключить в ковычки. -
{ # echo }Поставь тут хоть чё-нидь типа
{ # echo ; } -
Для установки ipcad на 2.0 beta 5 нужно ставить compat6x-i386 ?
-
Добрый день!
PF 1.2.3Чет парюсь второй день… Не хочет через веб интерфейс ставиться lightsquid
Зависает на этом месте (картинка) и ничего больше не пишет.
http://thin.kiev.ua/images/stories/pfsense/antivirus/lite.jpgДо вчера, всё ставилось на ура.
Видел, что пути к портам изменились.
Может подскажет кто, как и откуда, ручками установить lightsquid?Упс.
Увидел ошибку...Warning: main(squid.inc): failed to open stream: No such file or directory in /usr/local/pkg/lightsquid.inc on line 36 Fatal error: main(): Failed opening required 'squid.inc' (include_path='.:/etc/inc:/usr/local/www:/usr/local/captiveportal:/usr/local/pkg') in /usr/local/pkg/lightsquid.inc on line 36
-
Установите squid. Там требуется его файл.
-
Спасибо. Уже догадался… Поставил, все ок. Странно, что без сквида никак... Или поставить, а потом сквид удалить?
-
Спасибо. Уже догадался… Поставил, все ок. Странно, что без сквида никак... Или поставит, а потом сквид удалить?
Нет, там реконфигурация сквида происходит. Надо будет проверку наличия файла добавить.. Ну кто-же знал, что лайт еще как-то использоваться будет.
-
Подскажите пожалуйста что я не правильно сделал в конфигах так как ipcad не пишет ничего в лог.
Процесс в памяти висит.$ ifconfig em0: flags=8a43 <up,broadcast,running,allmulti,simplex,multicast>metric 0 mtu 1500 options=9b <rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum>ether 00:0c:29:5c:ed:fe inet 192.168.1.249 netmask 0xffffff00 broadcast 192.168.1.255 inet6 fe80::20c:29ff:fe5c:edfe%em0 prefixlen 64 scopeid 0x1 nd6 options=3 <performnud,accept_rtadv>media: Ethernet autoselect (1000baseT <full-duplex>) status: active em1: flags=8a43 <up,broadcast,running,allmulti,simplex,multicast>metric 0 mtu 1500 options=9b <rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum>ether 00:0c:29:5c:ed:08 inet 192.168.132.2 netmask 0xffffff00 broadcast 192.168.132.255 inet6 fe80::20c:29ff:fe5c:ed08%em1 prefixlen 64 scopeid 0x2 nd6 options=3 <performnud,accept_rtadv>media: Ethernet autoselect (1000baseT <full-duplex>) status: active em2: flags=8a43 <up,broadcast,running,allmulti,simplex,multicast>metric 0 mtu 1500 options=9b <rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum>ether 00:0c:29:5c:ed:12 inet 192.168.232.2 netmask 0xffffff00 broadcast 192.168.232.255 inet6 fe80::20c:29ff:fe5c:ed12%em2 prefixlen 64 scopeid 0x3 nd6 options=3 <performnud,accept_rtadv>media: Ethernet autoselect (1000baseT <full-duplex>) status: active em3: flags=8a43 <up,broadcast,running,allmulti,simplex,multicast>metric 0 mtu 1500 options=9b <rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum>ether 00:0c:29:5c:ed:1c inet 192.168.32.2 netmask 0xffffff00 broadcast 192.168.32.255 inet6 fe80::20c:29ff:fe5c:ed1c%em3 prefixlen 64 scopeid 0x4 nd6 options=3 <performnud,accept_rtadv>media: Ethernet autoselect (1000baseT <full-duplex>) status: active plip0: flags=8810 <pointopoint,simplex,multicast>metric 0 mtu 1500 lo0: flags=8049 <up,loopback,running,multicast>metric 0 mtu 16384 options=3 <rxcsum,txcsum>inet 127.0.0.1 netmask 0xff000000 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x6 nd6 options=3 <performnud,accept_rtadv>pfsync0: flags=0<> metric 0 mtu 1460 syncpeer: 224.0.0.240 maxupd: 128 pflog0: flags=100 <promisc>metric 0 mtu 33200 enc0: flags=0<> metric 0 mtu 1536</promisc></performnud,accept_rtadv></rxcsum,txcsum></up,loopback,running,multicast></pointopoint,simplex,multicast></full-duplex></performnud,accept_rtadv></rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum></up,broadcast,running,allmulti,simplex,multicast></full-duplex></performnud,accept_rtadv></rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum></up,broadcast,running,allmulti,simplex,multicast></full-duplex></performnud,accept_rtadv></rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum></up,broadcast,running,allmulti,simplex,multicast></full-duplex></performnud,accept_rtadv></rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum></up,broadcast,running,allmulti,simplex,multicast>#!/bin/sh net1="192.168.132" net2="192.168.232" net3="192.168.32" ttime=`/usr/bin/rsh localhost sh ip acco | grep 'Accounting data saved' | awk '{print ($4)}'` rsh localhost clear ip accounting rsh localhost show ip accounting checkpoint | grep $net1 | awk -v vtime=$ttime '{if ($5 != 0) print (vtime".000",1,$2,"TCP_MISS/200",$4,"CONNECT",$1":"$5,"-","DIRECT/"$1,"-")}' >> /var/squid/log/access.log rsh localhost show ip accounting checkpoint | grep $net2 | awk -v vtime=$ttime '{if ($5 != 0) print (vtime".000",1,$2,"TCP_MISS/200",$4,"CONNECT",$1":"$5,"-","DIRECT/"$1,"-")}' >> /var/squid/log/access.log rsh localhost show ip accounting checkpoint | grep $net3 | awk -v vtime=$ttime '{if ($5 != 0) print (vtime".000",1,$2,"TCP_MISS/200",$4,"CONNECT",$1":"$5,"-","DIRECT/"$1,"-")}' >> /var/squid/log/access.log# # Configuration file for ipcad - Cisco IP accounting simulator daemon. # Copyright (c) 2001, 2002, 2003, 2004, 2005 # Lev Walkin <vlm@lionet.info>. # # Please see ipcad.conf(5) for additional explanations. # Please contact me if you have troubles configuring ipcad. My goal is to make # initial configuration easier for new users, so your input is valuable. # ################## # GLOBAL OPTIONS # ################## # # Enable or disable capturing UDP and TCP port numbers, IP protocol and # ICMP types for RSH output. # # capture-ports {enable|disable} ; # # Enabling this will BREAK Cisco RSH output format compatibility, # increase memory requirements and may slow down traffic processing. # This option takes effect IMMEDIATELY, that is, it can be specified # multiple times, even between interfaces configuration. # This option has NO effect on NetFlow operation (NetFlow always captures # port information). # capture-ports enable; # # Buffers to be used for transferring the data from the kernel, # if applicable (BPF, ULOG). # Using larger buffers may increase the performance but will # affect responsiveness. # # buffers = <number>[{k|m}] ; # # Reasonable defaults are used if this parameter is not set. # ## buffers = 64k; ##################### # INTERFACE OPTIONS # ##################### # # interface <iface>[ promisc ] [ input-only ] # [ netflow-disable ] [ filter "<pcap_filter>" ] ; # OR # interface ulog group <group>[, group <group>...] # [ netflow-disabled ]; # OR # interface ipq [ netflow-disabled ]; # man libipq(3) # OR # interface {divert|tee} port <divert-port># man divert(4) # [ input-only ] [ netflow-disabled ]; # OR # interface file <tcpdump-output.pcap>[ netflow-disabled ]; # # Options meaning: # # promisc: # Put interface into promiscuous mode. # This enables listening for the packets which are not destined for # this host and thus ipcad will count and display all the traffic within # the local network. Note that the interface might be in promiscuous mode # for some other reason. # # input-only: # Use kernel feature of counting only incoming packets. # # netflow-sampled: (DO NOT ENABLE THIS OPTION, unless you have to!) # If the NetFlow export mechanism is used, this option instructs # the interface to supply only one out of N packets to the NetFlow # accounting code, thus lowering the CPU requirements. The value of N # is configured explicitly in a NetFlow configuration section. # NOTE: This option is NOT used to enable NetFlow on the interface, # it just modifies the NetFlow behavior on this interface. # DO NOT ENABLE THIS OPTION, UNLESS YOU HAVE TO! # # netflow-disable: # By default, all interfaces are included into NetFlow accounting. # This option is used to disable NetFlow on a particular interface. # # filter: # Install a custom filter on packets instead of basic # IP protocol filter. Requires libpcap (even if BPF is being used). # May be employed to eliminate CPU overhead on passing unnecessary # data between the kernel and user space (by installing the filter # directly into the kernel). # # NOTES: # * "input-only" directive must be supported by kernel. # Probably, you were noticed about it during the compilation process # if it was not supported. # FreeBSD 3.x and elder kernels do not support this feature. # * ULOG packet source (interface ulog) is supported under # Linux >= 2.4.18-pre8. # You should configure iptables to dump the packet stream # into the appropriate group, i.e.: # iptables -A OUTPUT -j ULOG --ulog-nlgroup <group># Given ULOG groups will be OR'ed together. # * A wildcard (*) may be specified as part of an interface name. # interface em1 filter "ip and dst net 192.168.132.0/24 and not src net 192.168.132.0/24 and not src port 80"; interface em2 filter "ip and dst net 192.168.232.0/24 and not src net 192.168.232.0/24 and not src port 80"; interface em3 filter "ip and dst net 192.168.32.0/24 and not src net 192.168.32.0/24 and not src port 80"; # # aggregate <ip>/ <masklen>strip <maskbits>; # # Aggregate addresses from the specified network (<ip>/<masklen>), # by AND'ing with specified mask (<maskbits>). # # aggregate 192.168.132.0/24 strip 32; /* Don't aggregate internal range */ aggregate 192.168.232.0/24 strip 32; /* Don't aggregate internal range */ aggregate 192.168.32.0/24 strip 32; /* Don't aggregate internal range */ aggregate 0.0.0.0/0 strip 32; /* Aggregate external networks */ # # aggregate <port_range_start>[-<port_range_end>] into <port>; # # Aggregate port numbers. Meaningful only if capture-ports is enabled. # #aggregate 1-19 into 65535; #aggregate 20-21 into 21; #aggregate 22-23 into 22; #aggregate 25 into 25; #aggregate 24 into 65535; #aggregate 26-79 into 65535; aggregate 80 into 0; #aggregate 81-109 into 65535; #aggregate 110 into 110; #aggregate 111-442 into 65535; #aggregate 443 into 443; #aggregate 444-3127 into 65535; #aggregate 3128 into 3128; #aggregate 3129-65535 into 65535; ########################## # NetFlow EXPORT OPTIONS # ########################## # # Enable Cisco NetFlow export method. # NetFlow uses UDP to feed flow information to the receiver. # If the destination is not specified, NetFlow is disabled. # # netflow export destination 127.0.0.1 9996; netflow export version 5; # NetFlow export format version {1|5} netflow timeout active 30; # Timeout when flow is active, in minutes netflow timeout inactive 15; # Flow inactivity timeout, in seconds netflow engine-type 73; # v5 engine_type; 73='I' for "IPCAD" netflow engine-id 1; # Useful to differentiate multiple ipcads. # The following option is enabled by the "netflow-sampled" interface flag. #netflow sampling-mode packet-interval 10; # 1 out of 10 packets accounted # DO NOT ENABLE THIS UNLESS YOU KNOW WHAT ARE YOU DOING. # # NetFlow protocol exports an SNMP id instead of the interface name # (i.e., "eth0", "ppp32"). The following statements options define # mapping between the interface names and a set of "SNMP identifiers". # netflow ifclass eth mapto 0-99; # i.e., "eth1"->1, "eth3"->3 netflow ifclass fxp mapto 0-99; # i.e., "fxp4"->4, "fxp0"->0 netflow ifclass ppp mapto 100-199; # i.e., "ppp32"->532, "ppp7"->507 netflow ifclass gre mapto 200-299; netflow ifclass tun mapto 300-399; # i.e., "tun0"->300 ###################### # RSH SERVER OPTIONS # ###################### # # Enable RSH Server: # # rsh {enable|yes|on|disable|no|off} [at <listen_ip>]; # # If "at <listen_ip>" omitted, rsh server listens on IP address 0.0.0.0, # which may be undesirable. # rsh enable at 127.0.0.1; # # RSH access rules: # # rsh [<user>@] <host_addr>{admin|backup|[default]|view-only|deny} ; # rsh root@127.0.0.1 admin; /* Can shutdown ipcad */ rsh root@127.0.0.1 backup; /* Can dump/restore/import accounting table */ rsh root@127.0.0.1; /* Can view and modify accounting tables */ /* Note the order! */ #rsh luser@127.0.0.1 deny; /* Deny this user from even viewing tables */ rsh 127.0.0.1 view-only; /* Other users can view current tables */ # Keep IP packet time to live reasonably low to avoid remote attacks. # (The rsh client must reside no more than three hops away from the # router running ipcad.) rsh ttl = 3; # Set rsh timeout for the same purpose. rsh timeout = 30; # # Dump active IP accounting table to this file on exit and read on startup. # (read about -s and -r options in ipcad(8) manual page) # NOTE: This setting has no effect on NetFlow operation. The flow cache # contents are flushed to the collector upon ipcad termination. # dumpfile = ipcad.dump; # The file is inside chroot(), see below... ################# # OTHER OPTIONS # ################# # # Chroot to this directory before processing. # # Of course, you could disable chroot()'ing by commenting it out, # but it is not recommended, so I left this confusing default # to encourage you to change it. # chroot = /var/log/ipcad; # # File to keep getpid() in it. ipcad will also hold a lock. # # WARNING: Pidfile is created AFTER chroot()'ing, so if you're using # chroot statement above, make sure the path to the pidfile exists # inside chrooted environment. # pidfile = ipcad.pid; # # UID/GID privileges dropping # Please note: RSH service will be UNAVAILABLE when uid is not zero. # Use it only when you know what are you doing (i.e., NetFlow without RSH). # # uid = 65534; # gid = 65534; # # Few useful settings. # # # Memory usage limit for storing per-stream entries. # # memory_limit = <number>[{k|m|e}] ; # Where k, m and g are for kilobytes, megabytes or table "entries". # memory_limit = 10m;</number></host_addr></user></listen_ip></listen_ip></port></port_range_end></port_range_start></maskbits></masklen></ip></maskbits></masklen></ip></group></tcpdump-output.pcap></divert-port></group></group></pcap_filter></iface></number></vlm@lionet.info> -
В доке кажись так:
interface le1 filter "ip and dst net 192.168.0.0/16 and not src net 192.168.0.0/16";
А у Вас?
Запустите процесс с одним интерфейсом, а потом лепите остальные.
И тут Очепатка….
aggregate 80 into 0;надо aggregate 80-81 into 0;
Ищите ошибки в конфигах.
И тут ошибка
dumpfile = ipcad.dump;
надо
dumpfile = /var/log/ipcad/ipcad.dump;
Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.