Core dump errors on RC1
-
I have a Hacom 1U unit (1Ghz Intel Celeron, Intel NIC's) that was working great on a beta4 revision. I updated it to RC1 and it croaked. I removed the CF card, used physdiskwrite to put on a new RC1 image from today and the same thing happened. Here are the outputs of two boots (log couldn't get it all). Any ideas?
nsesrc/src/sys/pfSense_wrap.8.i386 i386 Timecounter "i8254" frequency 1193182 Hz quality 0 CPU: Intel(R) Celeron(R) M processor 1.00GHz (999.89-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x6d8 Family = 6 Model = d Stepping = 8 Features=0xafe9fbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,tm,pbe>real memory = 1055784960 (1006 MB) avail memory = 1014583296 (967 MB) ACPI APIC Table: <intelr awrdacpi="">ioapic0 <version 2.0="">irqs 0-23 on motherboard wlan: mac acl policy registered ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/. ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (ipw_bss_fw, 0xc0701130, 0) error 1 ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/. ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc07011d0, 0) error 1 wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/. wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (wpi_fw, 0xc0873e80, 0) error 1 ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/. ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf. module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc0701270, 0) error 1 cryptosoft0: <software crypto="">on motherboard padlock0: No ACE support. acpi0: <intelr awrdacpi="">on motherboard acpi0: [ITHREAD] acpi0: Power Button (fixed) acpi0: reservation of 0, a0000 (3) failed acpi0: reservation of 100000, 3ede0000 (3) failed Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0 cpu0: <acpi cpu="">on acpi0 acpi_button0: <power button="">on acpi0 acpi_button1: <sleep button="">on acpi0 pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0 pci0: <acpi pci="" bus="">on pcib0 pci0: <base peripheral=""> at device 0.1 (no driver attached) pci0: <base peripheral=""> at device 0.3 (no driver attached) vgapci0: <vga-compatible display="">port 0xe900-0xe907 mem 0xe0000000-0xe7ffffff,0xe8200000-0xe827ffff irq 16 at device 2.0 on pci0 vgapci1: <vga-compatible display="">at device 2.1 on pci0 uhci0: <intel 82801db="" (ich4)="" usb="" controller="" usb-a="">port 0xeb00-0xeb1f irq 16 at device 29.0 on pci0 uhci0: [ITHREAD] usbus0: <intel 82801db="" (ich4)="" usb="" controller="" usb-a="">on uhci0 uhci1: <intel 82801db="" (ich4)="" usb="" controller="" usb-b="">port 0xed00-0xed1f irq 19 at device 29.1 on pci0 uhci1: [ITHREAD] usbus1: <intel 82801db="" (ich4)="" usb="" controller="" usb-b="">on uhci1 uhci2: <intel 82801db="" (ich4)="" usb="" controller="" usb-c="">port 0xe800-0xe81f irq 18 at device 29.2 on pci0 uhci2: [ITHREAD] usbus2: <intel 82801db="" (ich4)="" usb="" controller="" usb-c="">on uhci2 ehci0: <intel 82801db="" l="" m="" (ich4)="" usb="" 2.0="" controller="">mem 0xe8280000-0xe82803ff irq 23 at device 29.7 on pci0 ehci0: [ITHREAD] usbus3: EHCI version 1.0 usbus3: <intel 82801db="" l="" m="" (ich4)="" usb="" 2.0="" controller="">on ehci0 pcib1: <acpi pci-pci="" bridge="">at device 30.0 on pci0 pci1: <acpi pci="" bus="">on pcib1 em0: <intel(r) 1000="" pro="" legacy="" network="" connection="" 1.0.3="">port 0xd000-0xd03f mem 0xe8000000-0xe801ffff,0xe8020000-0xe803ffff irq 16 at device 0.0 on pci1 em0: [FILTER] em1: <intel(r) 1000="" pro="" legacy="" network="" connection="" 1.0.3="">port 0xd100-0xd13f mem 0xe8040000-0xe805ffff,0xe8060000-0xe807ffff irq 17 at device 1.0 on pci1 em1: [FILTER] em2: <intel(r) 1000="" pro="" legacy="" network="" connection="" 1.0.3="">port 0xd200-0xd23f mem 0xe8080000-0xe809ffff,0xe80a0000-0xe80bffff irq 18 at device 2.0 on pci1 em2: [FILTER] em3: <intel(r) 1000="" pro="" legacy="" network="" connection="" 1.0.3="">port 0xd300-0xd33f mem 0xe80c0000-0xe80dffff,0xe80e0000-0xe80fffff irq 19 at device 3.0 on pci1 em3: [FILTER] isab0: <pci-isa bridge="">at device 31.0 on pci0 isa0: <isa bus="">on isab0 atapci0: <intel ich4="" udma100="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 31.1 on pci0 ata0: <ata 0="" channel="">on atapci0 ata0: [ITHREAD] ata1: <ata 1="" channel="">on atapci0 ata1: [ITHREAD] pci0: <serial bus,="" smbus="">at device 31.3 (no driver attached) acpi_tz0: <thermal zone="">on acpi0 atrtc0: <at realtime="" clock="">port 0x70-0x73 irq 8 on acpi0 uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 uart0: [FILTER] uart0: console (9600,n,8,1) ppc0: parallel port not found. acpi_throttle0: <acpi cpu="" throttling="">on cpu0 Timecounter "TSC" frequency 999889604 Hz quality 800 Timecounters tick every 10.000 msec IPsec: Initialized Security Association Processing. usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 ugen0.1: <intel>at usbus0 uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0 ugen1.1: <intel>at usbus1 uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 480Mbps High Speed USB v2.0 ugen2.1: <intel>at usbus2 uhub2: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus2 ugen3.1: <intel>at usbus3 uhub3: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus3 ad2: 3831MB <cf 20091113="" card="" 4gb="">at ata1-master PIO4 uhub0: 2 ports with 2 removable, self powered Root mount waiting for: usbus3 usbus2 usbus1 uhub1: 2 ports with 2 removable, self powered uhub2: 2 ports with 2 removable, self powered Root mount waiting for: usbus3 Root mount waiting for: usbus3 uhub3: 6 ports with 6 removable, self powered Trying to mount root from ufs:/dev/ufs/pfsense1 Configuring crash dumps... Mounting filesystems... Setting up embedded specific environment...pid 32 (newfs), uid 0: exited on signal 11 mdmfs: mount exited witpid 38 (newfs), uid 0: exited on signal 11 h error code 1 mdmfs: mount exited with error code 1 done. pid 45 (ln), uid 0: exited on signal 11 (core dumped) Segmentation fault (core dumped) WARNING: R/W mount of /cf denied. Filesystem is not clean - run fsck mount: not currently mounted /cf umount: /cf: not a file system root directory pid 52 (fsck_ufs), uid 0: exited on signal 11 (core dumped) fsck: /dev/ufs/cf: SegWARNING: R/W mount of /cf denied. Filesystem is not clean - run fsck mentation fault: 11 mount: /devpid 55 (cut), uid 0: exited on signal 11 (core dumped) /ufs/cf : Operation not permittepid 61 (cut), uid 0: exited on signal 11 (core dumped) d ___ ___/ mode = 0100444, inum = 18192, fs = / panic: ffs_valloc: dup alloc cpuid = 0 Uptime: 9s Cannot dump. Device not defined or unavailable. Automatic reboot in 15 seconds - press a key on the console to abort --> Press a key on the console to reboot, --> or switch off the system now.</cf></intel></intel></intel></intel></intel></intel></intel></intel></acpi></at></thermal></serial></ata></ata></intel></isa></pci-isa></intel(r)></intel(r)></intel(r)></intel(r)></acpi></acpi></intel></intel></intel></intel></intel></intel></intel></intel></vga-compatible></vga-compatible></acpi></acpi></sleep></power></acpi></intelr></software></version></intelr></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,tm,pbe>
uhci1: [ITHREAD] usbus1: <intel 82801db="" (ich4)="" usb="" controller="" usb-b="">on uhci1 uhci2: <intel 82801db="" (ich4)="" usb="" controller="" usb-c="">port 0xe800-0xe81f irq 18 at device 29.2 on pci0 uhci2: [ITHREAD] usbus2: <intel 82801db="" (ich4)="" usb="" controller="" usb-c="">on uhci2 ehci0: <intel 82801db="" l="" m="" (ich4)="" usb="" 2.0="" controller="">mem 0xe8280000-0xe82803ff irq 23 at device 29.7 on pci0 ehci0: [ITHREAD] usbus3: EHCI version 1.0 usbus3: <intel 82801db="" l="" m="" (ich4)="" usb="" 2.0="" controller="">on ehci0 pcib1: <acpi pci-pci="" bridge="">at device 30.0 on pci0 pci1: <acpi pci="" bus="">on pcib1 em0: <intel(r) 1000="" pro="" legacy="" network="" connection="" 1.0.3="">port 0xd000-0xd03f mem 0xe8000000-0xe801ffff,0xe8020000-0xe803ffff irq 16 at device 0.0 on pci1 em0: [FILTER] em1: <intel(r) 1000="" pro="" legacy="" network="" connection="" 1.0.3="">port 0xd100-0xd13f mem 0xe8040000-0xe805ffff,0xe8060000-0xe807ffff irq 17 at device 1.0 on pci1 em1: [FILTER] em2: <intel(r) 1000="" pro="" legacy="" network="" connection="" 1.0.3="">port 0xd200-0xd23f mem 0xe8080000-0xe809ffff,0xe80a0000-0xe80bffff irq 18 at device 2.0 on pci1 em2: [FILTER] em3: <intel(r) 1000="" pro="" legacy="" network="" connection="" 1.0.3="">port 0xd300-0xd33f mem 0xe80c0000-0xe80dffff,0xe80e0000-0xe80fffff irq 19 at device 3.0 on pci1 em3: [FILTER] isab0: <pci-isa bridge="">at device 31.0 on pci0 isa0: <isa bus="">on isab0 atapci0: <intel ich4="" udma100="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 31.1 on pci0 ata0: <ata 0="" channel="">on atapci0 ata0: [ITHREAD] ata1: <ata 1="" channel="">on atapci0 ata1: [ITHREAD] pci0: <serial bus,="" smbus="">at device 31.3 (no driver attached) acpi_tz0: <thermal zone="">on acpi0 atrtc0: <at realtime="" clock="">port 0x70-0x73 irq 8 on acpi0 uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 uart0: [FILTER] uart0: console (9600,n,8,1) ppc0: parallel port not found. acpi_throttle0: <acpi cpu="" throttling="">on cpu0 Timecounter "TSC" frequency 999889837 Hz quality 800 Timecounters tick every 10.000 msec IPsec: Initialized Security Association Processing. usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 ugen0.1: <intel>at usbus0 uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0 ugen1.1: <intel>at usbus1 uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 480Mbps High Speed USB v2.0 ugen2.1: <intel>at usbus2 uhub2: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus2 ugen3.1: <intel>at usbus3 uhub3: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus3 ad2: 3831MB <cf 20091113="" card="" 4gb="">at ata1-master PIO4 uhub0: 2 ports with 2 removable, self powered Root mount waiting for: usbus3 usbus2 usbus1 uhub1: 2 ports with 2 removable, self powered uhub2: 2 ports with 2 removable, self powered Root mount waiting for: usbus3 Root mount waiting for: usbus3 uhub3: 6 ports with 6 removable, self powered Trying to mount root from ufs:/dev/ufs/pfsense1 WARNING: / was not properly dismounted Configuring crash dumps... Mounting filesystems... Setting up embedded specific environment... done. WARNING: R/W mount of / denied. Filesystem is not clean - run fsck mount: /dev/ufs/pfsense1 : Operation not permitted ** /dev/ufs/pfsense1 ** Last Mounted on / ** Root file system ** Phase 1 - Check Blocks and Sizes INCORRECT BLOCK COUNT I=15 (592 should be 104) CORRECT? yes INCORRECT BLOCK COUNT I=16 (568 should be 0) CORRECT? yes ** Phase 2 - Check Pathnames ** Phase 3 - Check Connectivity ** Phase 4 - Check Reference Counts ** Phase 5 - Check Cyl groups FREE BLK COUNT(S) WRONG IN SUPERBLK SALVAGE? yes SUMMARY INFORMATION BAD SALVAGE? yes BLK(S) MISSING IN BIT MAPS SALVAGE? yes 5914 files, 279876 used, 1590138 free (626 frags, 198689 blocks, 0.0% fragmentation) ***** FILE SYSTEM MARKED CLEAN ***** ***** FILE SYSTEM WAS MODIFIED ***** ** /dev/ufs/cf ** Last Mounted on /cf ** Phase 1 - Check Blocks and Sizes ** Phase 2 - Check Pathnames ** Phase 3 - Check Connectivity ** Phase 4 - Check Reference Counts ** Phase 5 - Check Cyl groups 7 files, 38 used, 101017 free (25 frags, 12624 blocks, 0.0% fragmentation) ***** FILE SYSTEM MARKED CLEAN ***** ___ ___/ f \ / p \___/ Sense \___/ \ \___/ Welcome to pfSense 2.0-RC1 ... Creating symlinks...rm: /conf: No such file or directory ...done. pid 237 (php), uid 0: exited on signal 11 (core dumped) Fatal error: Call to undefined function xml_parser_create() in /etc/inc/xmlparse.inc on line 169 appending output to nohup.out Launching the init system... done. Initializing............... Fatal error: Call to undefined function xml_parser_create() in /etc/inc/xmlparse.inc on line 169 Starting CRON... done. Fatal error: Call to undefined function xml_parser_create() in /etc/inc/xmlparse.inc on line 169 Executing rc.d items... Starting /usr/local/etc/rc.d/*.sh...done. Bootup complete grep: /var/log/dmesg.boot: No such file or directory [: -gt: unexpected operator rm: /tmp/config.cache: No such file or directory Fatal error: Call to undefined function xml_parser_create() in /etc/inc/xmlparse.inc on line 169 pid 374 (getty), uid 0: exited on signal 11 (core dumped) pid 375 (getty), uid 0: exited on signal 11 (core dumped) pid 376 (getty), uid 0: exited on signal 11 (core dumped) pid 377 (getty), uid 0: exited on signal 11 (core dumped) Mar 2 15:59:41 init: getty repeating too quickly on port /dev/console, sleeping 30 secs pid 378 (getty), uid 0: exited on signal 11 (core dumped) pid 379 (getty), uid 0: exited on signal 11 (core dumped) pid 380 (getty), uid 0: exited on signal 11 (core dumped) pid 381 (getty), uid 0: exited on signal 11 (core dumped) pid 382 (getty), uid 0: exited on signal 11 (core dumped) Mar 2 16:00:12 init: getty repeating too quickly on port /dev/console, sleeping 30 secs [/code]</cf></intel></intel></intel></intel></intel></intel></intel></intel></acpi></at></thermal></serial></ata></ata></intel></isa></pci-isa></intel(r)></intel(r)></intel(r)></intel(r)></acpi></acpi></intel></intel></intel></intel></intel>
-
That seems like your card is not working properly.
Or you are upgrading only one slice! -
I did try the second slice after I failed to boot the first time. I would not be surprised since I had a bad CF card from Hacom before and they sent me out the same kind.
What lines give it away that it's the CF card?