Setting up VLANs
-
Yes IEEE802.1Q is supported by the switch. I will give it a go once I finish work. thanks
Sleeps
-
Don't forget next thing. Usually devices with webgui supports gui to be working with native(default) vlan, so you'll have to check that you add also native vlan in that box. and from the switch side, dont tag that traffic.
native vlan traffic is always send without vlan tag.
-
You don't HAVE to use vlan1… If you only want 2 vlans you can just use vlan10 and vlan20. Just make sure you set all your switchports to access the vlan's you want.
I'm reading Metu's stuff... Are you trying to have two physical lans with one split by VLAN's?? I thought you just wanted one LAN with multiple VLAN's.
-
That's correct I want one LAN with multiple VLAN's. However I'm having serious problems with the switch (TL SG1209) been reading the PfSense Guide and having problems creating a trunk port. (In the manual it says Each Trunk should contain 2 to 4 ports. Trunk 1 = 1234 Trunk 2 = 5678) Only want to create 1 trunk and its not possible.
Any advice - driving me crazy.
Sleeps
-
Might help http://pfsense.site88.net/mysetup/switch/HP1800-8G_vlan_setup.htm
-
You only need one trunk per switch.. A trunk just carries information from multiple VLAN's accross it.
I work with Cisco gear.. So I don't know exactly on yours.
But for Cisco…
int e0/0
switchport mode trunk
switchport mode trunk encap dot1qAnd that port is now trunking whatever VLAN's you have created on it... You can get a lot more advanced than that. But you basically set the port into trunk mode... give it an encap mode. And you have a basic trunk.
If you only have 1 vlan there's nothing to trunk...
So you need a minimum of 2 for a trunk to have a point. -
@Keith: I didn't mention that vlan1 should be used, I only mentioned that default vlan might be "must to use"-list. As Procurves allow to change default vlan to someone else..
-
Might help http://pfsense.site88.net/mysetup/switch/HP1800-8G_vlan_setup.htm
Much appreciated. Looks simple and it was nearly the same sample (different switch) as in the book.
Sleeps
-
Created VLAN 10 and 20 (No trunk ports). Using port 8 on the switch to connect to the Firebox but not getting an IP address via DHCP. I have looked through the config and can't see anything wrong on the Firebox. Not sure what I'm doing wrong.
Sleeps
-
That port 8 what is connected to pfsense needs to be trunk
trunk means that it allows multiple vlans go in it, those cannot mixup, so thats why you have atleast OSI Layer 3 device to connect two vlans, in this case it's Pfsense.
IN SHORT: switch port 8 trunk and both vlans in it
-
I understand now will give it a go, thanks
Sleeps
-
Just tried creating the trunks and the following msg is appearing.
Trunk member must Be in same Vlan and egress must be same each other. Error exists in entry 1.
Trunk 1 = 1234 Trunk 2 = 5678) Vlan 10 = port 2 and 3 Vlan 20 = 4 and 5
Checked the ports.
I'm totally lost now.
Sleeps
-
Is it possible to have only one trunk?
but try this: switchport#1: trunk with vlan 10, vlan 20
switchport#2: access vlan 10
switchport#3: access vlan 20Just don't setup more, test if it works, maybe your switch needs 2 trunk ports, 1st and 2nd half of interfaces
-
Natu69salemi
Can only create 2 trunk ports and it's configured through Gui. Can I start from scratch and send you
screenshots. Will pay for your time. Let me know.Sleeps
-
Send me images, but if you're willing to pay something to someone, plz consider to donate to this project
-
Thanks for agreeing to do this. I will definitely donate some money to this project.
Sleeps
-
Replied
-
Metu69salemi - Thanks for helping out with this. I found some information about trunk groups. http://www.brocade.com/support/Product_Manuals/ServerIron_SwitchRouterGuide/Trunking.4.2.html#78207 and it explains how to setup 2 or more trunk groups (Which you can do with the TL-SL2109 switch (Minimum 2 ports per Trunk)). The 2 ports in a trunk group make a single logical link. Therefore, all the ports in a trunk group must be connected to the same device at the other end.
My question is I have a Firebox with WAN, LAN and 4 OPT ports. (existing network connected to WAN, LAN and OPT1) I have created 2 VLANS 10 and 20 on OPT2 on the Firebox. Would it be possible to connect both cables/Trunks to OPT2 and OPT3 and bind OPT3 to OPT2 so that I will be able to use the VLANS
If this isn't possible what is the way forward?
Thanks in advance
Sleeps
-
Only thing what bothers me is that I don't understand why trunk needs to be in group and why it requires to use more than one switchport.
I know what is the benefit of several trunking ports but i don't understand why this switch requires it(as an example procurve's dont require it but those support it), so how to add aironet access point with single interface to this switch.
edit: check lacp if you like to use several ports on pfsense
-
@Keith: I didn't mention that vlan1 should be used, I only mentioned that default vlan might be "must to use"-list. As Procurves allow to change default vlan to someone else..
Gotcha… Like I said I've mainly worked with Cisco so I wasn't aware that you couldn't change it.
And like said above definitely donate money to PFSense. I just bought the Definitive Guide written by some of the PFSense creators & got it in 1.5 days off Amazon. It's a great way to donate some money because you get something extremely useful in return. When the official book for 2.0 comes out I'll also buy that. But the book for 1.2.3 is still extremely useful & well written