IPv6 testing

alexis.olivier

Thanks to you for adding tickets.

In effect, i hadn't changed the repo URL.
But I changed it now and ran a fresh gitsync from "https://github.com/bsdperimeter/pfsense.git", and the "deny unknow clients" bug is still there.
Am i doing something wrong ? Is this the good URL ?

Thanks for your answers !

cmb

run 'rm -rf /root/pfsense*' and sync again from that URL. That's correct URL, but that's not where you're getting code from.

databeestje

We need to replace the current subnet range calculator for a v6 prefix. Its just outright wrong.

iFloris

I just ran into an interesting possible issue. In osx lion (10.7) all ethernet interfaces receive not one, but multiple v6 addresses. The first address is a stateless autoconfig address which has been the same since the very first pfsense-v6 builds. The second address seems to change every reboot.

I've even had three addresses show in this panel.
I'm not sure if this is a new feature in 10.7, if these addresses were there all along but weren't shown or if there is something up with the dvhpv6 server on my pfsense install. Any thoughts?

jimp

@iFloris:

I just ran into an interesting possible issue. In osx lion (10.7) all ethernet interfaces receive not one, but multiple v6 addresses. The first address is a stateless autoconfig address which has been the same since the very first pfsense-v6 builds. The second address seems to change every reboot.
[snip]
I've even had three addresses show in this panel.
I'm not sure if this is a new feature in 10.7, if these addresses were there all along but weren't shown or if there is something up with the dvhpv6 server on my pfsense install. Any thoughts?

The same thing happens on Windows, it gets multiple IPs per interface. I haven't looked too deeply, but it would really be nice if it just had the one address, from DHCPv6, and no others.

johnpoz

most likely you seeing multiple because of stateless autoconfiguration, not sure how to disable in os x, but on windows you can setup routerdiscovery=disabled with netsh, or you can do with dhcp option as well I do believe.

if you want turn off the auto ipv6 on linux you could do it with say this setting in your /etc/sysctl.conf replacing your interface of course.

net.ipv6.conf.eth0.autoconf=0

windexh8er

Is the IPv6 support going to be rolled up into the final release (i.e. SLAAC / DHCPv6)?

EDIT:

OK, so I see that IPv6 is not going to be in 2.0 for release:

http://redmine.pfsense.org/projects/pfsense/roadmap#2.1-IPv6

…so at this point is it better to just sync the git repo to add IPv6 to my current 2.0 snapshot - or start from scratch with the IPv6 ISO's here:

http://files.pfsense.org/jimp/ipv6/

Thanks!

jimp

Either way is fine. Personally, I just use stock images + gitsync. If you are installing from scratch already, you may as well use an iso from there. Those are getting a bit stale though, I need to make a new set one of these days.

iFloris

@jimp, @johnpoz thanks for the info, I did not know that Windows showed the same behaviour.
I thought it might be an issue, as I had not seen two or three v6 addresses under osx snow leopard (10.6).
Before 10.7, my machines only had the stateless autoconfig addresses.
It seems that 10.7 has silently added a dchpv6 feature, though my dhcpv6 leases page on pfsense doesn't show anything.
This blog post seems to agree with my findings.

Also, while searching for a way to disable stateless autoconfig as per @johnpoz's suggestion, I came accross a post on the same site as above explaining how to disable stateless autoconfig on windows xp, vista, 7 and osx 10.7 lion.

johnpoz

That link is not about autoconf, its about privacy – turning off the use of your MAC in the address generated.

iFloris

@johnpoz, you are right, I mistakenly assumed that privacy addressing and stateless autoconfig were the same thing.

windexh8er

@iFloris:

I just ran into an interesting possible issue. In osx lion (10.7) all ethernet interfaces receive not one, but multiple v6 addresses. The first address is a stateless autoconfig address which has been the same since the very first pfsense-v6 builds. The second address seems to change every reboot.

I've even had three addresses show in this panel.
I'm not sure if this is a new feature in 10.7, if these addresses were there all along but weren't shown or if there is something up with the dvhpv6 server on my pfsense install. Any thoughts?

This is due to how temporary addresses work in SLAAC and v6. If you do an ifconfig on your OS X terminal you'll see one of the two listed as temporary.

databeestje

Lion has a dhcp6 client, that wasn't there before, thus more addresses assigned.