[SOLVED] Tunnel Online but Not Routing to outside IPv6 Sites

a-a-ron

It appears there are a few bugs stopping the default route from being created, see my thread.

focalguy

Thanks ipv6kid. This may not be the "correct" way to do it but I also spent a couple hours going over every portion of my config after following the guide and nothing worked until I followed your instructions.

databeestje

as far as I can tell it did setup default routes for most if not all of the users.

There is a checkbox to designate that gateway being the default. The not so intuitive part is that both a v6 and a v4 can be toggled default.

I should really add a tag in the listing ;-)

focalguy

Both my v4 and my v6 gateways are set as default. There is no "default" route for V6 in my routing table though.

v4v6defaultgw.PNG_thumb

v6Routes.PNG_thumb

databeestje

It might be fixed when you git sync up to newer code. I think Jim also started on new images, not sure what happened to those.

kionez

AFAIK there's a problem in /etc/inc/system.inc at the line 420:

mwexec("/sbin/route change -inet6 default " . escapeshellarg($gatewayipv6) ."{$ifscope}");

if I do this on pfsense's console:


# route change -inet6 default 2001:470:XXXX:XXX::1
route: writing to routing socket: No such process
change net default: gateway 2001:470:XXXX:XXX::1: not in table

but if I manually add a fake default route and then change it, it works fine..


# route add -inet6 default ::1
add net default: gateway ::1
# route change -inet6 default 2001:470:XXXX:XXX::1
change net default: gateway 2001:470:XXXX:XXX::1

so, maybe it could be added to init script a fake default route for inet6 .

Another solution: check if there's a default inet6 route before changing it and using "add" instead of "change" if there's no default GW

[sorry for my poor english :) ]

databeestje

the route binary we use in pfSense will add a route if it doesn't exist with Change. Maybe you have a older binary snapshot.

kionez

I updated an old 1.2.3 installation to 2.0-RC3 with full-upgrade package, then updated to 2.1-DEVELOPMENT via "playback gitsync" to master version:


# md5 /sbin/route
MD5 (/sbin/route) = b8e47fdd0d5f1f3d249dd1b9ae69bd38

Maybe i have to do a fresh install of 2.0?

k.

databeestje

a 2.0 snapshot should work fine, then gitsync 2.1-DEVELOPMENT

focalguy

@databeestje:

It might be fixed when you git sync up to newer code. I think Jim also started on new images, not sure what happened to those.

Nice! I have a "default" now after updating the snap and gitsyncing. My box still doesn't seem to gitsync automatically after updating the snap but that's another issue. Thank for all your work on this!

kionez

@databeestje:

a 2.0 snapshot should work fine, then gitsync 2.1-DEVELOPMENT

I just installed a clean 2.0 snapshot ( pfSense-memstick-2.0-RC3-i386-20110621-1650.img ) then updated via gitsync to 2.1-DEVELOPMENT and the /sbin/route binary still don't work as expected (and has the same md5sum of old installation). When it tries to "route change", it fails.

Where I'm wrong? I've installed from a wrong source?

thanks in advance.
k.

kionez

@kionez:

Where I'm wrong? I've installed from a wrong source?

I've just missed a step!

Updated to "2.1-DEVELOPMENT (i386) built on Mon Sep 5 04:07:51 EDT 2011" via Auto Update, then gitsync and now /sbin/route seems working fine.

If i remove the default route for inet6, then "change" it ,route gives "No such process" error, but then the new default is set!

thanks

k.