All but one of my computers can route over to my other subnet.
-
I have 20+ systems and they all can access the other subnet just fine. I picked up 3 new aspire S3 notebooks and the 2 work fine but the 3rd cannot access the resources on the other subnet. After reloading windows 7 and drivers with no change, I went out an picked up another Aspire S3. Now with the new Aspire i have the same problem. If i replace the PFsense 10.0.2.1 with a basic linksys router the Aspire notebook that dose not work starts working. So I know that the Cisco and the PFsense 10.0.1.1 boxes are working fine, it must be the pfsense 10.0.2.1 box thats the problem.
Here is my network setup.
Acer 10.0.2.100 –> PFsense router LAN 10.0.2.1 --> Cisco router 10.0.2.2 --> WAN MPLS network --> Cisco Router 10.0.1.2--> PFsense LAN 10.0.1.1 --> server 10.0.1.10
I can ping the server and tracert to the server but i cannot access the server resources (file shares, website)
PFsense 10.0.2.1: route setting 10.0.1.0 to 10.0.2.2
PFsense 10.0.1.1: route setting 10.0.2.0 to 10.0.1.2
-
check pfsense Subnet mask u can set /8 for full subnet
-
Have you tried disabling the firewall in Windows entirely?
-
Windows firewall on/off no change
-
f you can ping and tracert the destination and have no ports blocked in firewall rules and other clients from the same network/location/subnet work ….
then i'm guessing the destination is blocking access, i highly doubt this has anything todo with pfsense
check if your 'server' does not block that client, or if you have an ip-conflict (multiple devices with same ip)
-
The server does not block acces i tested that. If i take my pfsesne box 10.0.2.1 out and replace it with a linksys basic router then my notebook connects just fine to the server. I also reloaded my firewall box with pfsense 2.0 (to make sure 201 was not the problem) and only changed the LAN ip and added 1 route statement to the base config and my notebook still cannot connect. What strainge is that i have now 4 of the same notebooks with windows 7 base install. The first 2 notebooks work fine the third will not connect so i went down a purchased the 4th fron a different store and pluged it in and it has the same problem. Could it be that i need to chage one of the PFsense advanced settings. Also on the notebook that cannot connect if i set its gateway to the cisco router of 10.0.2.2 then it connects just fine over to the server 10.0.1.10. I have also changed IP address on the noteboot and checked them for IP-conflicts.
This is crazy :o
-
closer inspection raises some questions for me …..
acer <--> pfsense1 lan | pfsense1 wan <--> cisco1 <--> MPLS network <--> Cisco2 <--> pfsense2 wan | pfsense2 lan <--> server 10.0.1.10
is that an accurate interpretation of your situation ?
do the subnets overlap or are they the same ?if yes then i can't imagine this ever working properly …
if you plug in a linksys router this would not be an issue because they probably have a different default subnet 192.168.1.0/24 and thus have no issuesperhaps you should consider changing the lan subnet's on both ends or change the subnet the cisco's are running on
good luck
-
here is a pic of my setup
-
Did you enabled "Bypass firewall rules for traffic on the same interface " on system advanced -> Firewall/Nat?
-
Bypass firewall rules for traffic on the same interface. That seems to have fixed it. thanks ;D