LCDProc 0.5.4-dev

Cino

the results were blank. I dont have anything set, left it for the system to decide. The dashboard says 299000.. I'll set a value and see what happens. Its been awhile since I looked at the lcdproc code, but I'm thinking there was default 10000 if nothing is set via the gui now that i think about it a little more

stephenw10

@tix
I can see from your logs that you still have 0.53 version of LCDd. So who knows what version of other files you have.
From my experience the 'reinstall package' button in the GUI does not seem to re download everything.
I suggest un-installing the package completely, checking for any left over files and then re-installing it.

Steve

tix

@stephenw10:

@tix
I can see from your logs that you still have 0.53 version of LCDd. So who knows what version of other files you have.
From my experience the 'reinstall package' button in the GUI does not seem to re download everything.
I suggest un-installing the package completely, checking for any left over files and then re-installing it.

Steve

Well aren't I the idiot? :P Didn't even notice that….

Ok so I've now uninstalled the package, cleaned all the various references to LCDd, lcdproc, sdeclcd.so that the "find" command could locate. Then I reinstalled the package except LCDd is missing... Isn't this supplied by the lcdproc-dev package or am I being an idiot again?

mdima

@tix:

@stephenw10:

@tix
I can see from your logs that you still have 0.53 version of LCDd. So who knows what version of other files you have.
From my experience the 'reinstall package' button in the GUI does not seem to re download everything.
I suggest un-installing the package completely, checking for any left over files and then re-installing it.

Steve

Well aren't I the idiot? :P Didn't even notice that….

Ok so I've now uninstalled the package, cleaned all the various references to LCDd, lcdproc, sdeclcd.so that the "find" command could locate. Then I reinstalled the package except LCDd is missing... Isn't this supplied by the lcdproc-dev package or am I being an idiot again?

Tix, LCDd is inside the package, very strange you don't have it… maybe a reboot between the uninstall and the reinstall could help..

mdima

@Cino:

the results were blank. I dont have anything set, left it for the system to decide. The dashboard says 299000.. I'll set a value and see what happens. Its been awhile since I looked at the lcdproc code, but I'm thinking there was default 10000 if nothing is set via the gui now that i think about it a little more

Ok, I've understood what happens… if there is nothing set the function just return 10000 as a constant.
I will fix this on the new version.

Ciao,
Michele

mdima

Hi Tix
@tix:

Also, the Load average is staying higher around between 0.60 and 1.4 where prior to this update it stayed less than 0.80 (even when updating RRD). Again not sure it's related but I don't think it's anything to worry about.

Will continue to monitor…

well… as more screens you add, as more the client and LCDd have to work. If you only enable one screen the load should fall. The variables that affect the load are: number of screens, refresh rate.

Ciao,
Michele

easyhugo

Hi Guys

Is it possible to ad this Lcd to

http://allnet.de/1577.html?&tx_mmallnetproductplugin_pi1[showUid]=421433&cHash=949c8a38a8
ftp://212.18.29.48/ftp/pub/allnet/utility-server/fw8888/lcm_server_1.0.tar.bz2

i,m trying this for some time but with no success, see other posts from me

thx max

mdima

@easyhugo:

Hi Guys

Is it possible to ad this Lcd to

http://allnet.de/1577.html?&tx_mmallnetproductplugin_pi1[showUid]=421433&cHash=949c8a38a8
ftp://212.18.29.48/ftp/pub/allnet/utility-server/fw8888/lcm_server_1.0.tar.bz2

i,m trying this for some time but with no success, see other posts from me

thx max

Hi Max (easyhugo),
it's impossible to know for me which driver this LCD panel uses… do you know the chipset? Can it use one of the drivers already made or you need another driver?

Ciao,
Michele

stephenw10

My German is very bad! :-[ (Only beaten by my non-existant Italian! ::))

However, according to [url=http://www.ipcop-forum.de/forum/viewtopic.php?f=22&t=26948#p231301]this post by IPCop ledgend Wintermute the display in the FW8888 is an LCM-162.

This doesn't appear to be supported directly by LCDproc but this blog post seems to show it is possible. That's quite old now so support maybe better integrated.

What drivers/versions have you tried?

Steve

Edit: This post confirms this.

tix

@mdima:

Tix, LCDd is inside the package, very strange you don't have it… maybe a reboot between the uninstall and the reinstall could help..

I've tried multiple times to get LCDd to install and all fail. I must have broken something with the various versions and/or updates. I'll try a clean install later this weekend maybe….

In any case, I have the updated files now. I did a clean install to VMware Player and installed the package and then scp'd the file over to my real pfsense.

So far so good as I've exceeded my 10 hour limit and everything is working with the screens and settings I mentioned in the previous post.

mdima

@tix:

So far so good as I've exceeded my 10 hour limit and everything is working with the screens and settings I mentioned in the previous post.

hehe! on my machines I am running it from thursday with a refresh of 1second, and it's still working great… maybe I am too much optimist, but I think we made it... ;) at least for this specific problem!

stephenw10

Yes I think you have definitely solved the LCDd 100% problem. 48hours+ for me on two boxes running sdeclcd driver, 1second refresh, and screens: time, uptime and load.
Looking good. :)

However I think the other problem is still present.
At boot or restarting packages when an IP change is detected the lcdproc package ends up being started and stopped multiple times. Before this could result in multiple clients running. I think this has been solved thanks to your kill loop. However today I switched on my resurected X-Core box and at the end of boot the LCDd daemon is running twice but with no client! :-\


[2.0.1-RELEASE][root@x-core.localdomain]/root(2): ps aux | grep lcd
root   17691  0.0  0.6  3656  1356  ??  IN    4:21PM   0:00.01 /bin/sh /usr/local/etc/rc.d/lcdproc.sh start
[2.0.1-RELEASE][root@x-core.localdomain]/root(3): ps aux | grep LCD
root   24707  0.0  0.5  3352  1148  ??  IN    4:21PM   0:00.01 /usr/local/sbin/LCDd -c /usr/local/etc/LCDd.conf
nobody 24902  0.0  0.6  3368  1408  ??  SNs   4:21PM   0:00.21 /usr/local/sbin/LCDd -c /usr/local/etc/LCDd.conf

Here is the relavent section of the boot log:


Feb 12 16:22:33 	apinger: Error while feeding rrdtool: Broken pipe
Feb 12 16:21:52 	LCDd: Listening for queries on 127.0.0.1:13666
Feb 12 16:21:52 	LCDd: Using Configuration File: /usr/local/etc/LCDd.conf
Feb 12 16:21:52 	LCDd: LCDd version 0.5.5 starting
Feb 12 16:21:49 	LCDd: Server shutting down on SIGTERM
Feb 12 16:21:49 	LCDd: Listening for queries on 127.0.0.1:13666
Feb 12 16:21:49 	LCDd: Using Configuration File: /usr/local/etc/LCDd.conf
Feb 12 16:21:49 	LCDd: LCDd version 0.5.5 starting
Feb 12 16:21:47 	php: lcdproc: Sync: End package sync
Feb 12 16:21:47 	php: lcdproc: Sync: Begin package sync
Feb 12 16:21:47 	LCDd: Server shutting down on SIGTERM
Feb 12 16:21:47 	php: lcdproc: Sync: End package sync
Feb 12 16:21:45 	LCDd: sock_send: socket write error
Feb 12 16:21:45 	LCDd: sock_send: socket write error
Feb 12 16:21:45 	LCDd: sock_send: socket write error
Feb 12 16:21:45 	LCDd: Client on socket 11 disconnected
Feb 12 16:21:45 	php: lcdproc: Sync: Restarting the service
Feb 12 16:21:45 	php: lcdproc: Sync: Begin package sync
Feb 12 16:21:45 	php: : Restarting/Starting all packages.
Feb 12 16:21:42 	check_reload_status: Reloading filter
Feb 12 16:21:42 	LCDd: Connect from host 127.0.0.1:11554 on socket 11
Feb 12 16:21:42 	sshlockout[51329]: sshlockout/webConfigurator v3.0 starting up
Feb 12 16:21:42 	login: login on console as root
Feb 12 16:21:41 	php: lcdproc: Start client procedure. Error counter: (0)
Feb 12 16:21:40 	php: : IPSEC: One or more IPsec tunnel endpoints has changed its IP. Refreshing.
Feb 12 16:21:40 	LCDd: Listening for queries on 127.0.0.1:13666
Feb 12 16:21:40 	LCDd: Using Configuration File: /usr/local/etc/LCDd.conf
Feb 12 16:21:40 	LCDd: LCDd version 0.5.5 starting
Feb 12 16:21:39 	check_reload_status: Starting packages
Feb 12 16:21:39 	php: : pfSense package system has detected an ip change 0.0.0.0 -> ... Restarting packages.
Feb 12 16:21:39 	php: : OpenNTPD is starting up.
Feb 12 16:21:39 	dnsmasq[44759]: ignoring nameserver 127.0.0.1 - local interface
Feb 12 16:21:39 	dnsmasq[44759]: ignoring nameserver 127.0.0.1 - local interface
Feb 12 16:21:39 	dnsmasq[44759]: using nameserver 192.168.1.1#53
Feb 12 16:21:39 	dnsmasq[44759]: reading /etc/resolv.conf
Feb 12 16:21:39 	php: : The command '/usr/bin/killall 'ntpd'' returned exit code '1', the output was 'killall: warning: kill -TERM 51784: No such process'
Feb 12 16:21:38 	php: : Creating rrd update script
Feb 12 16:21:38 	php: : Resyncing OpenVPN instances for interface WAN.
Feb 12 16:21:38 	php: lcdproc: Sync: End package sync
Feb 12 16:21:38 	php: lcdproc: Sync: Begin package sync
Feb 12 16:21:38 	php: lcdproc: Sync: End package sync
Feb 12 16:21:38 	php: lcdproc: Sync: Begin package sync
Feb 12 16:21:38 	php: : Restarting/Starting all packages.

It ends up starting and stopping 3 times.

Restarting the service again manually brings it back to normal.

Steve

tix

I'm not quite to 48 hours yet, 44 so far! :) and I agree, I think we might have it mostly beat.

Steve - I don't have the multiple process running on my x700 and everything seems fine on mine. Perhaps you have some leftover cruft like I did?

Brak

Reinstalled the latest dev package on my Firebox X Core.

LCDProc will not start I guess, the LCD just sits with "Thanks for using pfSense," and its random whether Services reports LCDProc as still running or stopped. Sometimes the server screen stays on and it says "Clients: 0 Server: 0"

Any idea what's my problem?

Feb 12 22:36:23 	LCDd: LCDd version 0.5.5 starting
Feb 12 22:36:23 	LCDd: Using Configuration File: /usr/local/etc/LCDd.conf
Feb 12 22:36:23 	LCDd: Listening for queries on 127.0.0.1:13666
Feb 12 22:36:23 	php: lcdproc: Start client procedure. Error counter: (0)
Feb 12 22:36:24 	php: lcdproc: Start client procedure. Error counter: (0)
Feb 12 22:36:24 	LCDd: Server shutting down on SIGTERM
Feb 12 22:36:26 	php: lcdproc: Start client procedure. Error counter: (0)
Feb 12 22:36:28 	php: lcdproc: Start client procedure. Error counter: (0)
Feb 12 22:36:30 	php: lcdproc: Start client procedure. Error counter: (0)
Feb 12 22:36:32 	php: lcdproc: Start client procedure. Error counter: (0)
Feb 12 22:36:34 	php: lcdproc: Start client procedure. Error counter: (0)
Feb 12 22:36:36 	php: lcdproc: Start client procedure. Error counter: (0)
Feb 12 22:36:38 	php: lcdproc: Start client procedure. Error counter: (0)
Feb 12 22:36:40 	php: lcdproc: Start client procedure. Error counter: (0)
Feb 12 22:36:42 	php: lcdproc: Start client procedure. Error counter: (0)
Feb 12 22:36:44 	php: lcdproc: Start client procedure. Error counter: (0)
Feb 12 22:36:46 	php: lcdproc: Start client procedure. Error counter: (0)

stephenw10

Brak, is that just after boot?
I think it's likely that the various delays in the script are causing a problem when the package is started and stopped in quick succession. This is especially true now that the kill loop will stop all running copies of either the client or the server.
In my case simply restarting the package from gui was enough to sort everything out. Given only one stop and start with no time limit it works fine.

Possibilities for some experimenting are:
The start script first kills the client and server then starts it. When sent a restart it effectively does stop-stop-start. Might be better to only have one stop routine?
Reduce or remove the delays in the script.

Steve

mdima

Hi,
yes, there's a problem when the package is resynced in quick succession. Now I am ill at home, and I will be home recovering for the next few days, after that I will investigate and fix the problem (Steve, your suggestions are a very good starting point).

For the moment the package should be started manually when this occurs.

Ciao,
Michele

Brak

@stephenw10:

Brak, is that just after boot?

Actually, it's both. Even using the Services GUI to start or restart the service will lead to this failure. :(

stephenw10

Hmm, well that's interesting.
If you run:
ps aux|grep lcd
or
ps aux|grep LCD
What do you see running when that happens?

My own X-Core box ends up with two LCDd servers running and no client after boot. Different from your box.
Are you running lots of screens?

Steve

stephenw10

I've doing some testing and it looks to me as if we have two factors causing this:

1. The 'stop' script has two 2 second sleep commands in it. It cannot possibly run in less than 4 seconds yet during boot up the service is started (stop-start) three times in that period.
The sleep call seems to me to have been included simply to allow the kill command time to operate. The do-while kill loop now in place would seem to eliminate that need however commenting out the sleep calls does not solve the problem, though it does alter the outcome.

2. The rc script gets stuck in the 'kill loop' causing all manner of trouble!
You can see this as the rc 'start' scipt is still running after boot which should never happen. It is stuck trying to kill one of the other process and failing for some reason. If you kill, LCDd for example, the script is then able to continue and spawns more servers and clients before finishing.

I have found that at least one instance of LCDd runs as root when it should drop to nobody. Does the rc script run as root? Is that why it cannot kill it?

More testing to be done…..

Steve

stephenw10

Although what I wrote above is true if you get an 'un-killable' process the main reason the lcdproc.sh remains running is that it is held open by the php call.
You need to background the process (&) like so:


$start .= "\t/usr/bin/nice -20 /usr/local/bin/php -f /usr/local/pkg/lcdproc_client.php &\n";

Steve