Different WANS for different LANS - how to force it?

rockbear

In your outbound rules you can setup "NOT" rules instead of "Any". Create 3 aliases. In them include 2 of the interface subnets. In the outbound rule for like priv_inside, set the destination to not the other 2 subnets. This way, if the destination is the other 2 networks it will not NAT, but for all other locations it will.

hmmmm… I may have been unclear. It's not NAT I am concerned about, but routing. If a user on 12.0.0.5 wants to access a service on 1.0.0.8, today he is just forwarded to the 1.0.0.1 interface. I want him to be natted behind 2.0.0.1 and then routed across the internet (not shown).

The advanced feature "gateway" allows me to set 2.0.0.1 as default gateway for all traffic from 12.0.0.5, but it appears the firewall prefers the more specific route 1.0.0.0/24 over the default route. This is completely correct in routing terms, but not what I need.

@podilarius:

On a side note, I am hoping those are not the IPs you are actually using.

Heh. They are not. It's simplified for.. ehm.. simplicity :)

podilarius

SO, if you set the gateway in the rules for the 12.0.0.1/24 and in the outbound NAT you set the correct interface, subnet and NAT address, it should work. Are you using any extra services like squid?

rockbear

@podilarius:

SO, if you set the gateway in the rules for the 12.0.0.1/24 and in the outbound NAT you set the correct interface, subnet and NAT address, it should work.

And it does work - as long as the destination is not a host on a network local to the pfsense unit. If it is, the gateway option is ignored, it seems.

Are you using any extra services like squid?

No.

podilarius

What does your rule state and what do your NAT rules look like?

rockbear

@podilarius:

What does your rule state and what do your NAT rules look like?

Rule on WLAN_inside:

Interface WLAN_inside
proto any
source WLAN_inside subnet
Gateway 3.0.0.2 [that is the router beyond WLAN_outside]

NAT on WLAN_outside:

interface WLAN_outside
Type Network 13.0.0.0/24
Translation 3.0.0.1

podilarius

So when you access something on 1.0.0.0/24 you want it to look like it is coming from 3.0.0.1 if you are accessing it from 13.0.0.1/24? Is the resource in line with the pfsense machine or a part of it? ( like in a DMZ or something ).

rockbear

@podilarius:

So when you access something on 1.0.0.0/24 you want it to look like it is coming from 3.0.0.1 if you are accessing it from 13.0.0.1/24?

When I access something on 1.0.0.0/24 from 13.0.0.0/24 (3.0.0.1), I want it to be routed to 3.0.0.2.

(I believe that what is actually happening is quite in line with the general principles of routing, assuming that setting "gateway" means only default gateway. I just hoped it would be the gateway for everything.)

Is the resource in line with the pfsense machine or a part of it? ( like in a DMZ or something ).

I am not sure what you mean?

podilarius

Can you post a traceroute?

rockbear

@podilarius:

Can you post a traceroute?

Hmm… That will be monday, when I'm back at the office. I can't connect to the client networks from here.

rockbear

@podilarius:

Can you post a traceroute?

OK, I think now would be a good time to revisit the drawing and put the real IPs in there:

130.225.127.240/24 192.38.116.3/25 130.226.237.50/29
priv_outside unpriv_outside WLAN_outside
(defgw) | | |
–--------------------------------
| pfsense |
----------------------------------
| | |
priv_inside unpriv_inside WLAN_inside
10.76.127.1/24 10.76.128.1/24 10.200.115.1/24

I NAT the users on priv_inside to 130.225.127.240
I NAT the users on unpriv_inside to 192.38.116.3
I NAT the users on WLAN_inside to 130.226.237.50

Also, these IP addresses are virtual IPs.

OK, now for the traceroutes. They're done on a host on 10.76.128.131. The unpriv_inside rule has a "permit unpriv_inside subnet to any" with a gateway of "192.38.116.1".

Traceroute to external site:

traceroute to www.funet.fi (81.90.77.32), 30 hops max, 60 byte packets
1 192.38.116.1 2.347 ms 2.474 ms 2.566 ms
2 130.225.204.6 1.619 ms 1.869 ms 1.959 ms
[..]
11 81.90.77.32 33.693 ms 33.801 ms 33.971 ms

Traceroute to local address:

traceroute to 130.225.127.1 (130.225.127.1), 30 hops max, 60 byte packets
1 10.76.128.2 0.299 ms 0.155 ms 0.225 ms
2 * * *
3 * * *
[..]
30 * * *

phil.davis

I think this would work. Add 6 rules, 2 on each inside LAN, to force traffic for the 2 other "local" outside subnets to the gateway you want.
Here are the 2 rules for WLAN_inside:
On WLAN_inside, pass all protocols, source 10.200.115.0/24, destination 130.225.127.0/24 and in Advanced Features, Gateway, select the WLAN_outside gateway address.
On WLAN_inside, pass all protocols, source 10.200.115.0/24, destination 192.38.116.0/25 and in Advanced Features, Gateway, select the WLAN_outside gateway address.

Do 2 rules for unpriv_inside and 2 for priv_inside to cover all the permutations.

Am I guessing that this configuration is good for testing. You can use a client in WLAN_inside to go out over the real internet and access a server that is available through unpriv_outside. That way you can test that the server really accessible from the internet and that the served web pages, applications etc actually work out in internet land.

rockbear

@phil.davis:

I think this would work. Add 6 rules, 2 on each inside LAN, to force traffic for the 2 other "local" outside subnets to the gateway you want.
Here are the 2 rules for WLAN_inside:
On WLAN_inside, pass all protocols, source 10.200.115.0/24, destination 130.225.127.0/24 and in Advanced Features, Gateway, select the WLAN_outside gateway address.
On WLAN_inside, pass all protocols, source 10.200.115.0/24, destination 192.38.116.0/25 and in Advanced Features, Gateway, select the WLAN_outside gateway address.

Excellent idea - and it even works :)

Thanks.