Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    Shuttle XS35v2 (D525/NM10) install failure

    Scheduled Pinned Locked Moved Problems Installing or Upgrading pfSense Software
    17 Posts 3 Posters 7.5k Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • stephenw10S
      stephenw10 Netgate Administrator
      last edited by

      Hmm, I thought FreeNAS was based on 8.2? There are two branches though, it's been a while.
      pfSense 2.0.1 is based on 8.1, almost all the same kernel modules will be there.
      Your hardware doesn't seem particularly exotic, I would expect it to just work.

      Do you have any on board raid component?

      Steve

      1 Reply Last reply Reply Quote 0
      • Z
        zandr
        last edited by

        No RAID, just the on-board NM10 (I see ICH7 messages scroll by).

        I'm surprised it doesn't work as well. I was more worried about the jme ethernet than anything else, frustrating that USB and SATA aren't right. :)

        1 Reply Last reply Reply Quote 0
        • stephenw10S
          stephenw10 Netgate Administrator
          last edited by

          Is your sata controller set to IDE (legacy) mode?

          There are many people running D525/NM10 based boards.

          Steve

          1 Reply Last reply Reply Quote 0
          • Z
            zandr
            last edited by

            I believe I've tried in both IDE and AHCI modes, but I can check again. That's one of the few things in the BIOS on this thing that you can change.

            Which mode should work?

            1 Reply Last reply Reply Quote 0
            • stephenw10S
              stephenw10 Netgate Administrator
              last edited by

              IDE mode, though it's normally more of an issue when booting from hard drive.

              At least that's what I thought but the boot troubleshooting page seems to suggest using AHCI. Again that's for hard disk booting though.  :-\

              Steve

              1 Reply Last reply Reply Quote 0
              • Z
                zandr
                last edited by

                So, last night's 2.1 snapshot installed without issue, in AHCI mode.
                As such, the rest of this is mostly of academic interest, if there's a desire to fix this for a possible 2.0.2.

                I did try both IDE and AHCI with 2.0.1 and neither worked. I don't have a serial dump, but if you want to look at the boot console output, here's a movie: http://gallery.me.com/n6mod#100121

                Here's dmesg and pciconf -l from the machine with 2.1 installed:

                [2.1-DEVELOPMENT][admin@paula.milewski.org]/root(4): dmesg
                Copyright © 1992-2012 The FreeBSD Project.
                Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
                The Regents of the University of California. All rights reserved.
                FreeBSD is a registered trademark of The FreeBSD Foundation.
                FreeBSD 8.3-RC2 #0: Fri Mar 23 22:12:25 EDT 2012
                    root@FreeBSD_8.3_pfSense_2.1.snaps.pfsense.org:/usr/obj./usr/pfSensesrc/src/sys/pfSense_SMP.8 amd64
                Timecounter "i8254" frequency 1193182 Hz quality 0
                CPU: Intel(R) Atom(TM) CPU D525  @ 1.80GHz (1802.69-MHz K8-class CPU)
                  Origin = "GenuineIntel"  Id = 0x106ca  Family = 6  Model = 1c  Stepping = 10
                  Features=0xbfebfbff <fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>Features2=0x40e31d <sse3,dtes64,mon,ds_cpl,tm2,ssse3,cx16,xtpr,pdcm,movbe>AMD Features=0x20100800 <syscall,nx,lm>AMD Features2=0x1 <lahf>TSC: P-state invariant
                real memory  = 4294967296 (4096 MB)
                avail memory = 4083130368 (3893 MB)
                ACPI APIC Table: <062311 APIC1651>
                FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
                FreeBSD/SMP: 1 package(s) x 2 core(s) x 2 HTT threads
                cpu0 (BSP): APIC ID:  0
                cpu1 (AP/HT): APIC ID:  1
                cpu2 (AP): APIC ID:  2
                cpu3 (AP/HT): APIC ID:  3
                ioapic0: Changing APIC ID to 4
                ioapic0 <version 2.0="">irqs 0-23 on motherboard
                netisr_init: forcing maxthreads to 1 and bindthreads to 0 for device polling
                wlan: mac acl policy registered
                ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
                ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
                module_register_init: MOD_LOAD (ipw_bss_fw, 0xffffffff80493e90, 0) error 1
                ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
                ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
                module_register_init: MOD_LOAD (ipw_ibss_fw, 0xffffffff80493f30, 0) error 1
                ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
                ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in /boot/loader.conf.
                module_register_init: MOD_LOAD (ipw_monitor_fw, 0xffffffff80493fd0, 0) error 1
                kbd1 at kbdmux0
                cryptosoft0: <software crypto="">on motherboard
                padlock0: No ACE support.
                acpi0: <shuttl shuttle="">on motherboard
                acpi0: [ITHREAD]
                ACPI Error: No handler for Region [ECRM] (0xffffff0002526080) [EmbeddedControl] (20101013/evregion-487)
                ACPI Error: Region EmbeddedControl(0x3) has no handler (20101013/exfldio-382)
                ACPI Error: Method parse/execution failed [\SB.PCI0.SBRG.EC0_._REG] (Node 0xffffff000252a880), AE_NOT_EXIST (20101013/psparse-633)
                acpi0: Power Button (fixed)
                acpi0: reservation of ffc00000, 300000 (3) failed
                acpi0: reservation of fee00000, 1000 (3) failed
                acpi0: reservation of 0, a0000 (3) failed
                acpi0: reservation of 100000, bf600000 (3) failed
                Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
                acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
                cpu0: <acpi cpu="">on acpi0
                cpu1: <acpi cpu="">on acpi0
                cpu2: <acpi cpu="">on acpi0
                cpu3: <acpi cpu="">on acpi0
                acpi_ec0: <embedded controller:="" gpe="" 0x1d="">port 0x62,0x66 on acpi0
                pcib0: <acpi host-pci="" bridge="">port 0xcf8-0xcff on acpi0
                pci0: <acpi pci="" bus="">on pcib0
                vgapci0: <vga-compatible display="">port 0xcc00-0xcc07 mem 0xfe980000-0xfe9fffff,0xd0000000-0xdfffffff,0xfe800000-0xfe8fffff irq 16 at device 2.0 on pci0
                agp0: <intel pineview="" svga="" controller="">on vgapci0
                agp0: aperture size is 256M, detected 8188k stolen memory
                vgapci1: <vga-compatible display="">mem 0xfe780000-0xfe7fffff at device 2.1 on pci0
                pci0: <multimedia, hda="">at device 27.0 (no driver attached)
                pcib1: <acpi pci-pci="" bridge="">irq 16 at device 28.0 on pci0
                pci1: <acpi pci="" bus="">on pcib1
                pcib2: <acpi pci-pci="" bridge="">irq 17 at device 28.1 on pci0
                pci2: <acpi pci="" bus="">on pcib2
                pci2: <base peripheral=""> at device 0.0 (no driver attached)
                pci2: <base peripheral,="" sd="" host="" controller=""> at device 0.2 (no driver attached)
                pci2: <base peripheral=""> at device 0.3 (no driver attached)
                jme0: <jmicron inc,="" jmc25x="" gigabit="" ethernet="">port 0xdc00-0xdc7f,0xd800-0xd8ff mem 0xfeaf4000-0xfeaf7fff irq 17 at device 0.5 on pci2
                jme0: Using 1 MSIX messages.
                miibus0: <mii bus="">on jme0
                jmphy0: <jmp211 10="" 100="" 1000="" media="" interface="">PHY 1 on miibus0
                jmphy0:  none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, 1000baseT-FDX-flow, 1000baseT-FDX-flow-master, auto, auto-flow
                jme0: [FILTER]
                pcib3: <acpi pci-pci="" bridge="">irq 19 at device 28.3 on pci0
                pci3: <acpi pci="" bus="">on pcib3
                pci3: <network>at device 0.0 (no driver attached)
                uhci0: <intel 82801g="" (ich7)="" usb="" controller="" usb-a="">port 0xc880-0xc89f irq 23 at device 29.0 on pci0
                uhci0: [ITHREAD]
                uhci0: LegSup = 0x2f00
                usbus0: <intel 82801g="" (ich7)="" usb="" controller="" usb-a="">on uhci0
                uhci1: <intel 82801g="" (ich7)="" usb="" controller="" usb-b="">port 0xc800-0xc81f irq 19 at device 29.1 on pci0
                uhci1: [ITHREAD]
                uhci1: LegSup = 0x2f00
                usbus1: <intel 82801g="" (ich7)="" usb="" controller="" usb-b="">on uhci1
                uhci2: <intel 82801g="" (ich7)="" usb="" controller="" usb-c="">port 0xc480-0xc49f irq 18 at device 29.2 on pci0
                uhci2: [ITHREAD]
                uhci2: LegSup = 0x2f00
                usbus2: <intel 82801g="" (ich7)="" usb="" controller="" usb-c="">on uhci2
                uhci3: <intel 82801g="" (ich7)="" usb="" controller="" usb-d="">port 0xc400-0xc41f irq 16 at device 29.3 on pci0
                uhci3: [ITHREAD]
                uhci3: LegSup = 0x2f00
                usbus3: <intel 82801g="" (ich7)="" usb="" controller="" usb-d="">on uhci3
                ehci0: <intel 82801gb="" r="" (ich7)="" usb="" 2.0="" controller="">mem 0xfe977c00-0xfe977fff irq 23 at device 29.7 on pci0
                ehci0: [ITHREAD]
                usbus4: EHCI version 1.0
                usbus4: <intel 82801gb="" r="" (ich7)="" usb="" 2.0="" controller="">on ehci0
                pcib4: <acpi pci-pci="" bridge="">at device 30.0 on pci0
                pci4: <acpi pci="" bus="">on pcib4
                isab0: <pci-isa bridge="">at device 31.0 on pci0
                isa0: <isa bus="">on isab0
                atapci0: <intel ich7="" sata300="" controller="">port 0xc080-0xc087,0xc000-0xc003,0xbc00-0xbc07,0xb880-0xb883,0xb800-0xb81f mem 0xfe977800-0xfe977bff irq 19 at device 31.2 on pci0
                atapci0: [ITHREAD]
                atapci0: AHCI called from vendor specific driver
                atapci0: AHCI v1.10 controller with 4 3Gbps ports, PM not supported
                ata2: <ata channel="">at channel 0 on atapci0
                ata2: [ITHREAD]
                ata3: <ata channel="">at channel 1 on atapci0
                ata3: [ITHREAD]
                ata4: <ata channel="">at channel 2 on atapci0
                ata4: [ITHREAD]
                ata5: <ata channel="">at channel 3 on atapci0
                ata5: [ITHREAD]
                pci0: <serial bus,="" smbus="">at device 31.3 (no driver attached)
                acpi_button0: <sleep button="">on acpi0
                acpi_button1: <power button="">on acpi0
                acpi_tz0: <thermal zone="">on acpi0
                atrtc0: <at realtime="" clock="">port 0x70-0x71 irq 8 on acpi0
                atkbdc0: <keyboard controller="" (i8042)="">port 0x60,0x64 irq 1 on acpi0
                atkbd0: <at keyboard="">irq 1 on atkbdc0
                kbd0 at atkbd0
                atkbd0: [GIANT-LOCKED]
                atkbd0: [ITHREAD]
                acpi_hpet0: <high precision="" event="" timer="">iomem 0xfed00000-0xfed003ff on acpi0
                Timecounter "HPET" frequency 14318180 Hz quality 900
                orm0: <isa option="" rom="">at iomem 0xce000-0xcf7ff on isa0
                sc0: <system console="">at flags 0x100 on isa0
                sc0: VGA <16 virtual consoles, flags=0x300>
                vga0: <generic isa="" vga="">at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
                ppc0: cannot reserve I/O port range
                p4tcc0: <cpu frequency="" thermal="" control="">on cpu0
                p4tcc1: <cpu frequency="" thermal="" control="">on cpu1
                p4tcc2: <cpu frequency="" thermal="" control="">on cpu2
                p4tcc3: <cpu frequency="" thermal="" control="">on cpu3
                Timecounters tick every 1.000 msec
                IPsec: Initialized Security Association Processing.
                usbus0: 12Mbps Full Speed USB v1.0
                usbus1: 12Mbps Full Speed USB v1.0
                usbus2: 12Mbps Full Speed USB v1.0
                usbus3: 12Mbps Full Speed USB v1.0
                usbus4: 480Mbps High Speed USB v2.0
                ad4: 114473MB <intel ssdsa2cw120g3="" 4pc10302="">at ata2-master UDMA100 SATA 3Gb/s
                ugen0.1: <intel>at usbus0
                uhub0: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus0
                ugen1.1: <intel>at usbus1
                uhub1: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus1
                ugen2.1: <intel>at usbus2
                uhub2: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus2
                ugen3.1: <intel>at usbus3
                uhub3: <intel 1="" 9="" uhci="" root="" hub,="" class="" 0,="" rev="" 1.00="" 1.00,="" addr="">on usbus3
                ugen4.1: <intel>at usbus4
                uhub4: <intel 1="" 9="" ehci="" root="" hub,="" class="" 0,="" rev="" 2.00="" 1.00,="" addr="">on usbus4
                uhub0: 2 ports with 2 removable, self powered
                uhub1: 2 ports with 2 removable, self powered
                uhub2: 2 ports with 2 removable, self powered
                uhub3: 2 ports with 2 removable, self powered
                uhub4: 8 ports with 8 removable, self powered
                SMP: AP CPU #1 Launched!
                SMP: AP CPU #2 Launched!
                SMP: AP CPU #3 Launched!
                Trying to mount root from ufs:/dev/ad4s1a
                pflog0: promiscuous mode enabled
                [2.1-DEVELOPMENT][admin@paula.milewski.org]/root(5): pciconf -l
                hostb0@pci0:0:0:0: class=0x060000 card=0xa0008086 chip=0xa0008086 rev=0x02 hdr=0x00
                vgapci0@pci0:0:2:0: class=0x030000 card=0xa0018086 chip=0xa0018086 rev=0x02 hdr=0x00
                vgapci1@pci0:0:2:1: class=0x038000 card=0xa0018086 chip=0xa0028086 rev=0x02 hdr=0x00
                none0@pci0:0:27:0: class=0x040300 card=0x20051297 chip=0x27d88086 rev=0x02 hdr=0x00
                pcib1@pci0:0:28:0: class=0x060400 card=0x20051297 chip=0x27d08086 rev=0x02 hdr=0x01
                pcib2@pci0:0:28:1: class=0x060400 card=0x20051297 chip=0x27d28086 rev=0x02 hdr=0x01
                pcib3@pci0:0:28:3: class=0x060400 card=0x20051297 chip=0x27d68086 rev=0x02 hdr=0x01
                uhci0@pci0:0:29:0: class=0x0c0300 card=0x20051297 chip=0x27c88086 rev=0x02 hdr=0x00
                uhci1@pci0:0:29:1: class=0x0c0300 card=0x20051297 chip=0x27c98086 rev=0x02 hdr=0x00
                uhci2@pci0:0:29:2: class=0x0c0300 card=0x20051297 chip=0x27ca8086 rev=0x02 hdr=0x00
                uhci3@pci0:0:29:3: class=0x0c0300 card=0x20051297 chip=0x27cb8086 rev=0x02 hdr=0x00
                ehci0@pci0:0:29:7: class=0x0c0320 card=0x20051297 chip=0x27cc8086 rev=0x02 hdr=0x00
                pcib4@pci0:0:30:0: class=0x060401 card=0x20051297 chip=0x24488086 rev=0xe2 hdr=0x01
                isab0@pci0:0:31:0: class=0x060100 card=0x20051297 chip=0x27bc8086 rev=0x02 hdr=0x00
                atapci0@pci0:0:31:2: class=0x010601 card=0x20051297 chip=0x27c18086 rev=0x02 hdr=0x00
                none1@pci0:0:31:3: class=0x0c0500 card=0x20051297 chip=0x27da8086 rev=0x02 hdr=0x00
                none2@pci0:2:0:0: class=0x088000 card=0x20051297 chip=0x2382197b rev=0x80 hdr=0x00
                none3@pci0:2:0:2: class=0x080501 card=0x20051297 chip=0x2381197b rev=0x80 hdr=0x00
                none4@pci0:2:0:3: class=0x088000 card=0x20051297 chip=0x2383197b rev=0x80 hdr=0x00
                jme0@pci0:2:0:5: class=0x020000 card=0x20051297 chip=0x0250197b rev=0x03 hdr=0x00
                none5@pci0:3:0:0: class=0x028000 card=0x817610ec chip=0x817610ec rev=0x01 hdr=0x00</intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></cpu></cpu></cpu></cpu></generic></system></isa></high></at></keyboard></at></thermal></power></sleep></serial></ata></ata></ata></ata></intel></isa></pci-isa></acpi></acpi></intel></intel></intel></intel></intel></intel></intel></intel></intel></intel></network></acpi></acpi></jmp211></mii></jmicron></acpi></acpi></acpi></acpi></multimedia,></vga-compatible></intel></vga-compatible></acpi></acpi></embedded></acpi></acpi></acpi></acpi></shuttl></software></version></lahf></syscall,nx,lm></sse3,dtes64,mon,ds_cpl,tm2,ssse3,cx16,xtpr,pdcm,movbe></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,apic,sep,mtrr,pge,mca,cmov,pat,pse36,clflush,dts,acpi,mmx,fxsr,sse,sse2,ss,htt,tm,pbe>

                1 Reply Last reply Reply Quote 0
                • stephenw10S
                  stephenw10 Netgate Administrator
                  last edited by

                  Good to know, still slightly odd.  ::)

                  You have a lot of unrecognised devices there, none0-5.

                  Steve

                  1 Reply Last reply Reply Quote 0
                  • ExolonE
                    Exolon
                    last edited by

                    none2@pci0:2:0:0:  class=0x088000 card=0x20051297 chip=0x2382197b rev=0x80 hdr=0x00
                    none3@pci0:2:0:2:  class=0x080501 card=0x20051297 chip=0x2381197b rev=0x80 hdr=0x00
                    none4@pci0:2:0:3:  class=0x088000 card=0x20051297 chip=0x2383197b rev=0x80 hdr=0x00

                    These are probably the 4:1 Card Reader (JMicron - 197b:2381, 197b:2382, 197b:2383)

                    none5@pci0:3:0:0:  class=0x028000 card=0x817610ec chip=0x817610ec rev=0x01 hdr=0x00

                    This is could possibly be the WiFi (Realtek - 10ec:8176)

                    none0@pci0:0:27:0:  class=0x040300 card=0x20051297 chip=0x27d88086 rev=0x02 hdr=0x00

                    Intel Audio (Intel - 8086:27d8)

                    none1@pci0:0:31:3:  class=0x0c0500 card=0x20051297 chip=0x27da8086 rev=0x02 hdr=0x00

                    This appears to be the ICH7 chipset (Intel - 8086:27da)

                    1 Reply Last reply Reply Quote 0
                    • Z
                      zandr
                      last edited by

                      none1@pci0:0:31:3:   class=0x0c0500 card=0x20051297 chip=0x27da8086 rev=0x02 hdr=0x00

                      This appears to be the ICH7 chipset (Intel - 8086:27da)

                      Which would explain why I can't mount anything, yes?

                      1 Reply Last reply Reply Quote 0
                      • stephenw10S
                        stephenw10 Netgate Administrator
                        last edited by

                        That is the SMB controller in the ICH7 chipset:

                        pci0: <serial bus,="" smbus="">at device 31.3 (no driver attached)</serial>

                        It's not stopping you mounting anything.

                        I don't recall ever seeing a PCI attached card reader before, they are almost always USB, but that looks like what it is.

                        The last item looks like an RTL8188CE, as you said. It's very unlikely you will get this to work with pfSense. There are no FreeBSD drivers so you have to use NDIS wrapper.

                        Steve

                        1 Reply Last reply Reply Quote 0
                        • Z
                          zandr
                          last edited by

                          Yeah, couldn't care less about that wireless card. I might replace it with something more useful down the road, but for now I'm using an external AP.

                          And you're right, that pciconf is from the working system. So, if there's no interest in fixing this hardware for 2.0 (or understanding why 2.1 works where 2.0 doesn't), then I think we can call this one solved. :)

                          1 Reply Last reply Reply Quote 0
                          • First post
                            Last post
                          Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.