When I click the Advanced and MLPPP ,then PF server dead.
-
What does this page say?
/diag_logs_ppp.php
restart server get log show:
Last 50 PPP log entries
Jan 1 16:50:45 ppp: [wan] IPCP: state change Initial –> Starting
Jan 1 16:50:45 ppp: [wan] IPCP: LayerStart
Jan 1 16:50:45 ppp: [wan] IPV6CP: Open event
Jan 1 16:50:45 ppp: [wan] IPV6CP: state change Initial –> Starting
Jan 1 16:50:45 ppp: [wan] IPV6CP: LayerStart
Jan 1 16:50:45 ppp: [wan] IPCP: Up event
Jan 1 16:50:45 ppp: [wan] IPCP: state change Starting –> Req-Sent
Jan 1 16:50:45 ppp: [wan] IPCP: SendConfigReq #1
Jan 1 16:50:45 ppp: [wan] IPADDR 0.0.0.0
Jan 1 16:50:45 ppp: [wan] COMPPROTO VJCOMP, 16 comp. channels, no comp-cid
Jan 1 16:50:45 ppp: [wan] PRIDNS 0.0.0.0
Jan 1 16:50:45 ppp: [wan] SECDNS 0.0.0.0
Jan 1 16:50:45 ppp: [wan] IPV6CP: Up event
Jan 1 16:50:45 ppp: [wan] IPV6CP: state change Starting –> Req-Sent
Jan 1 16:50:45 ppp: [wan] IPV6CP: SendConfigReq #1
Jan 1 16:50:45 ppp: [wan] IPCP: rec'd Configure Request #110 (Req-Sent)
Jan 1 16:50:45 ppp: [wan] IPADDR 124.114.64.1
Jan 1 16:50:45 ppp: [wan] 124.114.64.1 is OK
Jan 1 16:50:45 ppp: [wan] IPCP: SendConfigAck #110
Jan 1 16:50:45 ppp: [wan] IPADDR 124.114.64.1
Jan 1 16:50:45 ppp: [wan] IPCP: state change Req-Sent –> Ack-Sent
Jan 1 16:50:45 ppp: [wan] IPCP: rec'd Configure Reject #1 (Ack-Sent)
Jan 1 16:50:45 ppp: [wan] COMPPROTO VJCOMP, 16 comp. channels, no comp-cid
Jan 1 16:50:45 ppp: [wan] IPCP: SendConfigReq #2
Jan 1 16:50:45 ppp: [wan] IPADDR 0.0.0.0
Jan 1 16:50:45 ppp: [wan] PRIDNS 0.0.0.0
Jan 1 16:50:45 ppp: [wan] SECDNS 0.0.0.0
Jan 1 16:50:45 ppp: [wan_link0] LCP: rec'd Protocol Reject #172 (Opened)
Jan 1 16:50:45 ppp: [wan_link0] LCP: protocol IPV6CP was rejected
Jan 1 16:50:45 ppp: [wan] IPV6CP: protocol was rejected by peer
Jan 1 16:50:45 ppp: [wan] IPV6CP: state change Req-Sent –> Stopped
Jan 1 16:50:45 ppp: [wan] IPV6CP: LayerFinish
Jan 1 16:50:45 ppp: [wan] IPCP: rec'd Configure Nak #2 (Ack-Sent)
Jan 1 16:50:45 ppp: [wan] IPADDR 124.114.67.24
Jan 1 16:50:45 ppp: [wan] 124.114.67.24 is OK
Jan 1 16:50:45 ppp: [wan] PRIDNS 218.30.19.50
Jan 1 16:50:45 ppp: [wan] SECDNS 61.134.1.5
Jan 1 16:50:45 ppp: [wan] IPCP: SendConfigReq #3
Jan 1 16:50:45 ppp: [wan] IPADDR 124.114.67.24
Jan 1 16:50:45 ppp: [wan] PRIDNS 218.30.19.50
Jan 1 16:50:45 ppp: [wan] SECDNS 61.134.1.5
Jan 1 16:50:45 ppp: [wan] IPCP: rec'd Configure Ack #3 (Ack-Sent)
Jan 1 16:50:45 ppp: [wan] IPADDR 124.114.67.24
Jan 1 16:50:45 ppp: [wan] PRIDNS 218.30.19.50
Jan 1 16:50:45 ppp: [wan] SECDNS 61.134.1.5
Jan 1 16:50:45 ppp: [wan] IPCP: state change Ack-Sent –> Opened
Jan 1 16:50:45 ppp: [wan] IPCP: LayerUp
Jan 1 16:50:45 ppp: [wan] 124.114.67.24 -> 124.114.64.1
Jan 1 16:50:46 ppp: [wan] IFACE: Up event
Jan 1 16:50:46 ppp: [wan] IFACE: Rename interface ng0 to pppoe6 -
I don't see any attempt for MLPPP in those logs… Are you sure you have MLPPP service?
-
When I creat an PPPOE link and I want to setup the Advanced and MLPPP. when I click that,then PF server down. why I can't click it?
what's need me do it ?
MY ISP support MUlti-PPPOE for link and get Different ipv4 ip address and Different ipv4 gateway from ISP.
Mybe I can setup PPPoE link Aggregation ?
I find the codes http://mpd.sourceforge.net/, it is help for this?
-
I don't see any attempt for MLPPP in those logs… Are you sure you have MLPPP service?
So the PF server down when click that, I am restart server after, just I can get and see logs.
-
I need to take my test box to the office where I have MLPPP service myself. Until then I cannot answer.
What is the reason you are running a beta?
I use 2.0.1 at the office and MLPPP works just fine there.
-
I need to take my test box to the office where I have MLPPP service myself. Until then I cannot answer.
What is the reason you are running a beta?
I use 2.0.1 at the office and MLPPP works just fine there.
I am need full support ipv6. So I try newest version. I hope setup PPPoE link Aggregation.
I think click pfsense web php page not should dead. it is should show any information.
-
Yon-
Have you ever made MLPPP work before?
Does it work with an earlier version of pfSense?
-
No, I still not try use it. I am new build PFsense server.
Just I know MY ISP support multi PPPoE.
-
I find edit about PPPoe things, then PF server dead.
-
I have update to 2.1-DEVELOPMENT-i386-20120403-1619. but the wrong still no fix.
-
Crash reporter
Crash report begins. Anonymous machine information:
i386
8.3-RC2
FreeBSD 8.3-RC2 #1: Wed Apr 4 08:00:43 EDT 2012 root@FreeBSD_8.3_pfSense_2.1.snaps.pfsense.org:/usr/obj./usr/pfSensesrc/src/sys/pfSense_SMP.8Crash report details:
PHP Errors:
[13-Jan-2003 14:05:39 UTC] PHP Parse error: syntax error, unexpected $end, expecting T_VARIABLE or '$' in /usr/local/pkg/filer.inc on line 178Filename: /var/crash/minfree
2048
