Pfsense and trixbox NAT port 5060 registering issues
-
I have pfsense 1.2.3 and i have a trixbox behind the firewall and i cant get it register the phones.
I have tried NAT with for 5060 fwd to trixbox ip and still no register.
I have read the getting SIP 5060 to work through pfsense is pretty tough. Can anybody guid em in the direction of getting this to work.
SIP.conf in trixbox is as follows
externhost=jasperXXXXXXXXX.XXXXXXXX.com
localnet=192.168.1.0/255.255.255.0
nat=yesI have tried outbound nat but no luck
-
hi,
i'm not sure if there's SIP issues but maybe you can post a rough topology of your network and firewall/nat settings in pfsense for the community to look at?
-
Dsl line to modem ppoe on dsl modem into wan side of pfsense box.
I have ports 5060, 10000through 20000 and 4569 forwarded to 192.168.20 which is the trix also
Have rules set as well. I see the the trixbox sees the connection but it never connects. -
I am not sure what the issue is the trixbox sees the connection but dont connect.
I read that alos of people have to use siproxd. I have tried it as well and still jo luck but i not sure on how to correctly set it up.
-
Dsl line to modem ppoe on dsl modem into wan side of pfsense box.
I have ports 5060, 10000through 20000 and 4569 forwarded to 192.168.20 which is the trix also
Have rules set as well. I see the the trixbox sees the connection but it never connects.Whats the wan address of your pfsense box? Private space?
If it is your double NAT'd
VOIP doesn't like being behind a NAT device let alone two… Can you put your modem in bridge mode and set up your pfsense box to do the pppoe?
-
VOIP doesn't like being behind a NAT device let alone two… Can you put your modem in bridge mode and set up your pfsense box to do the pppoe?
The wan address is 76.XX.XX.XX BG0 lan bg0 is 192.168.0.1. The adress the modem is 192.168.0.1. that as in the config GUI. the modem is a speedstream 4100. It is just a dsl moden router.
-
76.XX.XX.XX
Of your pfsense WAN?
The part of your dsl modem being a router is what Im trying to understand. If its actually routing and not in bridge mode then its likely your problem. If your pfsense box actually has the public IP address then something else is up…
-
The address of the wan is my public ip address. I can see the trixbox try to register but it never does
-
Did you check all the logs in pfsense?
I assume the "trixbox try to register" message come from within TrixBox where it receive request for registration etc.
-
Yes when you look at the connections in trixbox this is what to see The ext i have remotely is 1001
Version
Asterisk 1.6.0.26-FONCORE-r78 built by root @ revisor.trixbox.com on a i686 running Linux on 2010-06-08 22:01:27 UTC
Uptime
System uptime: 12 hours, 36 minutes, 26 seconds
Last reload: 12 hours, 36 minutes, 26 secondsActive Channel(s)
Peer User/ANR Call ID Format Hold Last Message
166.137.XXX.XXX (None) BJhxoO172xH.tvM 0x0 (nothing) No Rx: REGISTER
166.137.XXX.XXX (None) 3NCIUI8ELMX.RrO 0x0 (nothing) No Rx: REGISTER
2 active SIP dialogsSip Registry
Host Username Refresh State Reg.Time
0 SIP registrations.Sip Peers
Name/username Host Dyn Nat ACL Port Status
1004 (Unspecified) D N A 5060 UNKNOWN
1003/1003 192.168.1.14 D N A 5060 OK (90 ms) This is my cisco 7940inside my LAN already.
1001 (Unspecified) D N A 5060 UNKNOWN
1000 (Unspecified) D N A 5060 UNKNOWN
4 sip peers [Monitored: 1 online, 3 offline Unmonitored: 0 online, 0 offline] -
Quick Question your LAN subnet is 192.168.1. but your NAT inbound port forwarding is going to 192.168.20. is your trixbox on a VLAN / Different subnet to your IP phones if so why?
also are you using IAX for one of your trunk providers (Port 4569)
