Comcast 6to4 how-to?
-
I can corroborate irvingpop's results with the Apr 13th snapshot.
-
I have not yet found the time to debug this yet, it should be adding a new default route. But it isn't
-
Can not replicate on a static IPv4 wan, need to try dhcp later. It does add the static route for me, and the gateways also still exist.
-
OK, I've got a strange new problem. I updated to today's snaphot, added the ipv6 gateway as default ipv6 route manually, and now my computers can ONLY browse by ipv6 - ipv4 isn't working at all. I can ping either ipv6 or ipv4 addresses from pfSense. It looks like the DHCP server on pfSense may not be handing out the default gateway for ipv4 networks. Once I added the ipv4 default route manually on my windows box, ipv4 worked fine. ::)
EDIT: Looks like I can't connect to the webConfigurator, now. Not sure what's up with that, unless it's not listening on ipv4.
-
I just updated 2 installs with the latest snapshot and i'm not seeing anything like your issues.
May I suggest that your install is hosed? I can't even resemble anything close to your issues.
I did just commit a change that would disable the IPv4 gateway in the DHCP4 server but that is a very specific change that would only bite you if you had no ipv4 gateways at all. Dynamic or otherwise.
-
I managed to get a install online on a public IP with dhcp and I managed to replicate your issue. Seems like a timing issue.
-
Easily fixed?
-
I think it is now, I changed the default gateway address, as well as configuring the interface before trying to configure routing is generally a good idea.
fixed rc.newwanip and function interface_6to4_configure();
-
configuring the interface before trying to configure routing is generally a good idea.
;)
So, just a gitsync, and off to the races?
-
yep, no binary changes required
-
OK, I just did a gitsync and nothing seems to have changed. I then installed the latest snapshot, which was a few hours newer and did another gitsync. I still have no ipv4 gateway on my PC, and no default ipv6 route on pfSense.
Just to be clear, to do a gitsync, you SSH into the box, hit 12 for pfSense Developer Shell, type 'playback gitsync git://github.com/bsdperimeter/pfsense.git', and hit enter a couple times, right? I also rebooted a few times, just for fun - both the PC and pfSense. Did I miss something?
EDIT: Also, there is only the ipv6 gateway listed under Status -> Gateways. The ipv4 gateway is missing.
EDIT: I tried adding an ipv4 LAN gateway in the GUI, and a strange thing happened. The original ipv4 LAN gateway reappeared, but I couldn't set it as default, and I couldn't get the new LAN gateway to work. I just delelted all the ipv6 settings on the interfaces, and everything is back to normal - minus ipv6 support, of course. Now, I'm going to try to add the settings back. Maybe it'll work this time around.
EDIT: I'm about to reset to defaults. Nothing else has worked.
-
wow, yeah, that sounds horrific, i'm really not sure what has gone wrong but it appears it's thoroughly confused.
The VM I setup for testing has a WAN_DHCP gateway for IPv4 and a WAN_6to4 gateway for ipv6.
Both of those gateways are automatically added by the system during setup. I did start with a clean install of 2.1 which may be the difference.
I had no time to setup a test vm behind it to verify I actually got a v4 gateway on the LAN, but i do see a "routers" line in /var/dhcpd/etc/dhcpd.conf do you have such a line in your dhcpd.conf?
-
All is working now for me. Both v4 and v6 gateways and routes came up fine at boot. Thanks again!
Using this snapshot: built on Tue Apr 17 06:39:44 EDT 2012
One question. I'm using IPv6 Prefix ID "none". Is that the correct configuration or is it better to assign a prefix ID?
 -
assign something other then "none" and it will get assigned to the LAN interface.
A 6to4 wan has 65535 choices. 0000 to ffff.
-
Strange, after changing the Prefix ID to 1 (chosen arbitrarily) from none, pfSense could no longer ping the IPv6 gateway (WAN_6TO4) – even after reboot. However, everything else worked (ex. ping6 ipv6.google.com from both pfsense and machines on LAN).
Changing back to none (and reboot) and the WAN_6TO4 gateway is pingable from pfsense again.
-
I still haven't gotten around to starting over. :-[ Would a "Reset to factory defaults" be just as good, or will that leave something behind?
EDIT: Went ahead and did it and - woohoo! - 6to4 is now working as it should. Must have been all the various versions I've gone through over the last year that messed it up. I still get that error on line 42 at startup, though.
-
I think there might be a corrupt PHP file in /usr/local/pkg from a defunct package.
-
Is there anyway I can check for what's causing it and remove it? If I'm not mistaken, it did this on the first boot, before I had added any packages.
-
ls -l /usr/local/pkg see if there is a file there that you don't recognize.