Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    Inter-vlan routing

    Scheduled Pinned Locked Moved General pfSense Questions
    24 Posts 5 Posters 13.0k Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • K
      ka3ax
      last edited by

      @stephenw10:

      It would be interesting to compare performance, thoughput, cpu usage etc with both VLANs on the PCI-X card. If you have time.  :)

      The same test played with both VLANs on the PCI-X card. Transfer rate is 50-55MBps and CPU load is 35-45% (no device polling enabled)… Not much faster...

      1 Reply Last reply Reply Quote 0
      • stephenw10S
        stephenw10 Netgate Administrator
        last edited by

        A slightly reduced cpu load though. Hmm.

        I guess a 64bit pci slot is not going to be restricting you. Is the PCI card 64 bit though? I'd be surprised.

        Steve

        1 Reply Last reply Reply Quote 0
        • K
          ka3ax
          last edited by

          @stephenw10:

          Is the PCI card 64 bit though? I'd be surprised.

          PCI card is 32bit indeed

          1 Reply Last reply Reply Quote 0
          • stephenw10S
            stephenw10 Netgate Administrator
            last edited by

            It's an interesting topic this, to me at least.
            I had quite a long discussion a while ago when I discovered that a box I was working on had 4 gigbit NICs that were all on the same PCI bus. I was trying to get a definitive answer on what maximum theorectical throughput would be between two interfaces on that bus but never quite got to grips with it. It would be nice to know just so I don't end up hoping to push more data than I could ever possibly achieve.
            I guess with almost everything going to PCI-e it's less of an issue these days.

            Steve

            Edit: I wonder if both your slots are on the same bus by any chance? What do you see from pciconf -lv.

            1 Reply Last reply Reply Quote 0
            • K
              ka3ax
              last edited by

              @stephenw10:

              I wonder if both your slots are on the same bus by any chance? What do you see from pciconf -lv.

              Here is the output:

              
              $ pciconf -lv
              hostb0@pci0:0:0:0:	class=0x060000 card=0x00000000 chip=0x00171166 rev=0x32 hdr=0x00
                  class      = bridge
                  subclass   = HOST-PCI
              hostb1@pci0:0:0:1:	class=0x060000 card=0x00000000 chip=0x00171166 rev=0x00 hdr=0x00
                  class      = bridge
                  subclass   = HOST-PCI
              skc0@pci0:0:3:0:	class=0x020000 card=0x4b011186 chip=0x4b011186 rev=0x11 hdr=0x00
                  class      = network
                  subclass   = ethernet
              vgapci0@pci0:0:4:0:	class=0x030000 card=0x01411028 chip=0x47521002 rev=0x27 hdr=0x00
                  class      = display
                  subclass   = VGA
              atapci0@pci0:0:5:0:	class=0x010185 card=0x01411028 chip=0x06801095 rev=0x02 hdr=0x00
                  class      = mass storage
                  subclass   = ATA
              hostb2@pci0:0:15:0:	class=0x060000 card=0x02011166 chip=0x02031166 rev=0xa0 hdr=0x00
                  class      = bridge
                  subclass   = HOST-PCI
              atapci1@pci0:0:15:1:	class=0x01018a card=0x01411028 chip=0x02131166 rev=0xa0 hdr=0x00
                  class      = mass storage
                  subclass   = ATA
              ohci0@pci0:0:15:2:	class=0x0c0310 card=0x02201166 chip=0x02211166 rev=0x05 hdr=0x00
                  class      = serial bus
                  subclass   = USB
              isab0@pci0:0:15:3:	class=0x060100 card=0x02301166 chip=0x02271166 rev=0x00 hdr=0x00
                  class      = bridge
                  subclass   = PCI-ISA
              hostb3@pci0:0:16:0:	class=0x060000 card=0x00000000 chip=0x01101166 rev=0x12 hdr=0x00
                  class      = bridge
                  subclass   = HOST-PCI
              hostb4@pci0:0:16:2:	class=0x060000 card=0x00000000 chip=0x01101166 rev=0x12 hdr=0x00
                  class      = bridge
                  subclass   = HOST-PCI
              bge0@pci0:1:3:0:	class=0x020000 card=0x007c0e11 chip=0x164514e4 rev=0x15 hdr=0x00
                  class      = network
                  subclass   = ethernet
              
              

              Another note: when I do the same test without pfSense (both test workstations are on the same switch and on the same subnet) I can see transfer rate of 80-90MBps…

              1 Reply Last reply Reply Quote 0
              • stephenw10S
                stephenw10 Netgate Administrator
                last edited by

                Hmmm, I don't see either em or ste interfaces in that list.
                However skc0 and bge0 are on different buses. skc0 is on bus 0 along with everything else so it will have to share the bandwidth.

                Steve

                Edit: I should have said pciconf -lc. That should show your cards capabilities further.

                1 Reply Last reply Reply Quote 0
                • K
                  ka3ax
                  last edited by

                  here it is:

                  
                  $ pciconf -lc
                  hostb0@pci0:0:0:0:	class=0x060000 card=0x00000000 chip=0x00171166 rev=0x32 hdr=0x00
                  hostb1@pci0:0:0:1:	class=0x060000 card=0x00000000 chip=0x00171166 rev=0x00 hdr=0x00
                  skc0@pci0:0:3:0:	class=0x020000 card=0x4b011186 chip=0x4b011186 rev=0x11 hdr=0x00
                      cap 01[48] = powerspec 2  supports D0 D1 D2 D3  current D0
                      cap 03[50] = VPD
                  vgapci0@pci0:0:4:0:	class=0x030000 card=0x01411028 chip=0x47521002 rev=0x27 hdr=0x00
                      cap 01[5c] = powerspec 2  supports D0 D1 D2 D3  current D0
                  atapci0@pci0:0:5:0:	class=0x010185 card=0x01411028 chip=0x06801095 rev=0x02 hdr=0x00
                      cap 01[60] = powerspec 2  supports D0 D1 D2 D3  current D0
                  hostb2@pci0:0:15:0:	class=0x060000 card=0x02011166 chip=0x02031166 rev=0xa0 hdr=0x00
                  atapci1@pci0:0:15:1:	class=0x01018a card=0x01411028 chip=0x02131166 rev=0xa0 hdr=0x00
                  ohci0@pci0:0:15:2:	class=0x0c0310 card=0x02201166 chip=0x02211166 rev=0x05 hdr=0x00
                  isab0@pci0:0:15:3:	class=0x060100 card=0x02301166 chip=0x02271166 rev=0x00 hdr=0x00
                  hostb3@pci0:0:16:0:	class=0x060000 card=0x00000000 chip=0x01101166 rev=0x12 hdr=0x00
                      cap 07[60] = PCI-X 64-bit supports 133MHz, 512 burst read, 8 split transactions
                  hostb4@pci0:0:16:2:	class=0x060000 card=0x00000000 chip=0x01101166 rev=0x12 hdr=0x00
                      cap 07[60] = PCI-X 64-bit supports 133MHz, 512 burst read, 8 split transactions
                  bge0@pci0:1:3:0:	class=0x020000 card=0x007c0e11 chip=0x164514e4 rev=0x15 hdr=0x00
                      cap 07[40] = PCI-X 64-bit supports 133MHz, 512 burst read, 1 split transaction
                      cap 01[48] = powerspec 2  supports D0 D3  current D0
                      cap 03[50] = VPD
                      cap 05[58] = MSI supports 8 messages, 64 bit 
                  
                  
                  1 Reply Last reply Reply Quote 0
                  • stephenw10S
                    stephenw10 Netgate Administrator
                    last edited by

                    What happened to your Intel NIC?

                    Steve

                    1 Reply Last reply Reply Quote 0
                    • K
                      ka3ax
                      last edited by

                      It is swapped with HP NC7770 PCI-X gigabit server adapter, see my Reply #5. Intel NIC goes to another test.

                      @ka3ax:

                      In this test my vlans are on HP NC7770 gigabit server adapter.

                      1 Reply Last reply Reply Quote 0
                      • stephenw10S
                        stephenw10 Netgate Administrator
                        last edited by

                        Ah yes.  :-[

                        1 Reply Last reply Reply Quote 0
                        • First post
                          Last post
                        Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.