Web server behind pfsense 2 firewall

lankanatha

but still it doesnt work,
please provide step by step configuration for redirect port 80 to internal server.
thank you.

lankanatha,

Create aliases for both of the IP's (Internal Web Server and External IP that you use for your domain).
Then make port forward for the desired ports.

Attached you can get the example.

nat.jpg_thumb

cmb

That last post's screenshot is correct assuming the WANIF alias contains an IP assigned to your WAN (or an IP routed to you, or a virtual IP). What's in that alias?

JSmorada

I'm having what appears to be a related problem. My pfSense 2.0.1 box was running great until a thunderstorm knocked out the power. When I tried to bring the firewall back up, the file system was corrupt to the point where I had to do an install from scratch. I used the latest config backup I had, which was from Feb 2012, but when it got to "conifguring firewall" on the console, it would hang. So, I started from scratch. I have a web server behind the firewall that I make accessible to the outside world but whenever I try to access a web page on it, it tries to go in as https instead of http. Is there something I'm missing here? I tried the suggestions below and it still isn't working. This shouldn't be rocket science and I've done it before…

Thank You,
Jon

JSmorada

Unfortunately, I couldn't afford to have my web server down, so I had to fall back to an old FVS-318 and have a Juniper appliance on the way.

@nipstech:

I'm having what appears to be a related problem. My pfSense 2.0.1 box was running great until a thunderstorm knocked out the power. When I tried to bring the firewall back up, the file system was corrupt to the point where I had to do an install from scratch. I used the latest config backup I had, which was from Feb 2012, but when it got to "conifguring firewall" on the console, it would hang. So, I started from scratch. I have a web server behind the firewall that I make accessible to the outside world but whenever I try to access a web page on it, it tries to go in as https instead of http. Is there something I'm missing here? I tried the suggestions below and it still isn't working. This shouldn't be rocket science and I've done it before…

Thank You,
Jon

chpalmer

@lankanatha:

Hi,
i want setup web server behind firewall.please tell step by step instruction for fresh installation of pfsense 2.
thank you.

i have pc with two NIC
wan–---> real ip(xxx.xxx.xx.xx/27)
LAN----->172.16.1.1/24

Make your LAN 172.16.1.0/12

lankanatha

WANIF is alias of wan ip
@cmb:

That last post's screenshot is correct assuming the WANIF alias contains an IP assigned to your WAN (or an IP routed to you, or a virtual IP). What's in that alias?

lankanatha

i think you are right…this is not software error...it is hardware.hardware geometry error.
my problem is very simple..but isnt work.previously i used freebsd 8 as my gateway.after thunderstorm
its damaged.after that i had installed it correctly but portforwarding isnt work.this is bug of freebsd.
hence i thought use pfsense as gateway and installed it on same server.but it still not working.
:-(
hardware error(slice error??)

@nipstech:

I'm having what appears to be a related problem. My pfSense 2.0.1 box was running great until a thunderstorm knocked out the power. When I tried to bring the firewall back up, the file system was corrupt to the point where I had to do an install from scratch. I used the latest config backup I had, which was from Feb 2012, but when it got to "conifguring firewall" on the console, it would hang. So, I started from scratch. I have a web server behind the firewall that I make accessible to the outside world but whenever I try to access a web page on it, it tries to go in as https instead of http. Is there something I'm missing here? I tried the suggestions below and it still isn't working. This shouldn't be rocket science and I've done it before…

Thank You,
Jon

JSmorada

That could be the case. The machine was already on it's last leg; the caps on the mobo were starting to swell and the +5v on the power supply sometimes goes under voltage. Whenever I come across another pc; I'll try again.

@lankanatha:

i think you are right…this is not software error...it is hardware.hardware geometry error.
my problem is very simple..but isnt work.previously i used freebsd 8 as my gateway.after thunderstorm
its damaged.after that i had installed it correctly but portforwarding isnt work.this is bug of freebsd.
hence i thought use pfsense as gateway and installed it on same server.but it still not working.
:-(
hardware error(slice error??)

@nipstech:

I'm having what appears to be a related problem. My pfSense 2.0.1 box was running great until a thunderstorm knocked out the power. When I tried to bring the firewall back up, the file system was corrupt to the point where I had to do an install from scratch. I used the latest config backup I had, which was from Feb 2012, but when it got to "conifguring firewall" on the console, it would hang. So, I started from scratch. I have a web server behind the firewall that I make accessible to the outside world but whenever I try to access a web page on it, it tries to go in as https instead of http. Is there something I'm missing here? I tried the suggestions below and it still isn't working. This shouldn't be rocket science and I've done it before…

Thank You,
Jon

lankanatha

change it..but notworking.
@chpalmer:

@lankanatha:

Hi,
i want setup web server behind firewall.please tell step by step instruction for fresh installation of pfsense 2.
thank you.

i have pc with two NIC
wan–---> real ip(xxx.xxx.xx.xx/27)
LAN----->172.16.1.1/24

Make your LAN 172.16.1.0/12

nahid

lankanatha,

WANIF should be the IP address of your web server as you are going to port forward the web traffic to send them to ur local web server.

Try to follow this steps:

First create an alias (for example BlaWebSeverExternal) with the External IP address of your Web Address
Create another alias with the Internal IP address (For example BlaWebSeverInternal) of your Web Address
Then create a port forward that will forward the web traffic on HTTP port from BlaWebSeverExternal to BlaWebSeverInternal
If it works for HTTP port (80) then add another rule in the same that will forward the traffic on 81 and 82 port as well.

lankanatha

i did it,but it doesnt work.:-(

@nahid:

lankanatha,

WANIF should be the IP address of your web server as you are going to port forward the web traffic to send them to ur local web server.

Try to follow this steps:

First create an alias (for example BlaWebSeverExternal) with the External IP address of your Web Address

Create another alias with the Internal IP address (For example BlaWebSeverInternal) of your Web Address

Then create a port forward that will forward the web traffic on HTTP port from BlaWebSeverExternal to BlaWebSeverInternal

If it works for HTTP port (80) then add another rule in the same that will forward the traffic on 81 and 82 port as well.