PfSense 'modem' -> pfsense 'router(s)', would this work?

jonesr

Hi stephenw10, happy new year!

Take another look at the picture of the card, here http://linitx.com/viewproduct.php?prodid=12181

As I understand it the card can be used as a modem/router on it's own - I mean no PC necessary, it works without plugging it in to the PCI slot of a motherboard. I haven't tried this as it's not what I intended for it so I could be wrong but if you see the small white header just above the left hand side of the PCI connector, this is apparently for external power if NOT being used as a PCI card. It's a 5 pin header simply marked 'CN3' and in the document that comes with it it states 'Ethernet - 5/12V' or 'PCI - open' (what little comes with it is pretty sparse on detail).

Like I say don't take my word for that I may have misunderstood. But that would explain the option to set it up via ethernet from a 2nd PC via web browser by connecting to the onboard NIC. I've seen your other posts on similar cards that use CLI or telnet to manage the card, I went for the GUI/HTTP option so I can't tell you if this card supports other methods of access or management. If set to PCI mode, the onboard NIC is disabled (I stopped getting link lights on the switch it was still connected to) and only the ADSL RJ11 connector and PCI for access as a computer PCI peripheral are enabled.

I haven't spotted anything that would stop it doing what I want it to do, and at £44 it's a lot cheaper than many other cards I've seen.

stephenw10

I can't think why you'd ever want to run a PCI card that isn't in a PCI slot. Weird! Perhaps it's to allow the on-board router to be setup before it's send out to a customer?

Good to get a second positive review of it though.

Happy New Year!

Steve

jonesr

Hi all

A thousand apologies, I had forgotten all about this. "Life happened" and things like job hunting took priority. Also my ISP kept insisting that the network upgrade that would change my static IPs would happen "very soon" and I was waiting for that to fiddle again, which still hasn't happened. Excuses aside, sorry it has taken five months to post back.

Here are the screenshots for the PCI ADSL modem interface. I did my best to capture as much useful information as I could but please note that the steps noted along with the screenshots refer to what I clicked on, not what is visible at the time, due to the way I captured it. I hope this helps and provides some answers. What I have configured works for me, a great deal of the settings here I imagine are only relevant if you use the "Ethernet" option mentioned previously. Once configured the jumpers on the card should be set to "PCI" mode for use with pfSense so anything you set on the card like NAT or firewalling may well conflict with or be ignored by pfSense.

As far as the pfSense side goes I will do my best to write up what I have done but the majority of it is about routing multiple public IPs. The actual modem side is relatively easy due to my ISP, all I do is set my WAN to "static". Other users may need to research PPPoE or other WAN configurations, for BE (UK ISP) users try this - https://www.bethere.co.uk/web/beportal/techguides_other_modems_with_Be_broadband

stephenw10, and any others still interested in this, this may all be a little late as many UK ISPs offer FTTx, which I understand requires a BT VDSL modem no matter who your ISP is. Mine has not yet upgraded, but if you have upgraded your connection to FTTx to the best of my knowledge NONE OF THIS IS ANY GOOD TO YOU. But to those still on standard ADSL please consider whether you wish to invest the ~£50 on the modem if you too may upgrade to FTTx.

–-Sorry, the file is 2MB, maximum size for attachments per file is 250KB. Until I come up with a better solution please PM me for the screenshots, I will email them if you send me your address.