D-Link DFE-580TX 4 port Server Adapter problem: only 2 of 4 ports

stephenw10

Are you sure it's not on the NIC? It's not uncommon to have a bridge chip on multiport cards.

It looks like the device recognised as pcib3 is the one to look at (as you have done), it has device ID b152 which equates to the Intel Corporation 21152 PCI-to-PCI Bridge as referenced in the link.

Could be no difference but it looks like you have missed a : in your pciconf test. It should be:

pciconf -rb pci0:0:2:0: 0x3e

If you can boot the same box into Ubuntu does it show a similar output for that device from lspci -vvxxx? Specifically is it showing 'NoISA+'?

Since there are other people using this card with no problems I would suggest this problem can be worked around in other ways. I would first try disabling everything you can in the BIOS that you don't need. This may free up resources such that the NIC does try to use ISA address space.

Steve

matguy

I have a few of these cards sitting around, they certainly do have a PCI bridge chip, I want to say it's an Intel one, but can't say off the top of my head. I'll try to take a look tonight when I get home.

matguy

@matguy:

I have a few of these cards sitting around, they certainly do have a PCI bridge chip, I want to say it's an Intel one, but can't say off the top of my head. I'll try to take a look tonight when I get home.

Quick Google image search found a pic of one, it's an Intel chip:

http://files.dlink.com.au/Products/DFE-580TX/Images/DFE-580TX_A4_Image_Front_L.jpg

stephenw10

Nice. It is indeed the 21152 bridge chip as I thought. The biggest chip on the card! ::)

Steve

matguy

I remember these cards working fine in m0n0wall, I would think they'd work fine in pfSense.

stephenw10

You would and in fact there seem to be a number reports here on the forum of successful use. All of them old though so perhaps there has been some regression somewhere.
I think there is a strong possibility that this is s BIOS bug/incompatibility. Is there a more recent BIOS?

Steve

jmserrano

@stephenw10:

Are you sure it's not on the NIC? It's not uncommon to have a bridge chip on multiport cards.

It looks like the device recognised as pcib3 is the one to look at (as you have done), it has device ID b152 which equates to the Intel Corporation 21152 PCI-to-PCI Bridge as referenced in the link.

Could be no difference but it looks like you have missed a : in your pciconf test. It should be:
pciconf -rb pci0:0:2:0: 0x3e
If you can boot the same box into Ubuntu does it show a similar output for that device from lspci -vvxxx? Specifically is it showing 'NoISA+'?

Since there are other people using this card with no problems I would suggest this problem can be worked around in other ways. I would first try disabling everything you can in the BIOS that you don't need. This may free up resources such that the NIC does try to use ISA address space.

Steve

Thanks for the answers.

This card was working fine until I need to change motherboard to the Intel Atom D2500HN.

I have disabled the bios features that i don't use. Nothing change.

This is the result (booting on ubuntu) of lspci -vvxxx (before).

02:00.0 PCI bridge: Intel Corporation 21152 PCI-to-PCI Bridge (prog-if 00 [Norma
l decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step
ping- SERR- FastB2B+ DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <tabort - <mabort->SERR- <perr- intx-<br="">Latency: 32, Cache Line Size: 64 bytes
Bus: primary=02, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00001000-00001fff
Prefetchable memory behind bridge: 00000000d0300000-00000000d03fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <tabort - <mabort- <serr-="" <perr-<br="">BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied="">Kernel modules: shpchp
00: 86 80 52 b1 07 02 90 02 00 00 04 06 10 20 01 00
10: 00 00 00 00 00 00 00 00 02 03 03 00 11 11 80 02
20: f0 ff 00 00 31 d0 31 d0 00 00 00 00 00 00 00 00
30: 00 00 00 00 dc 00 00 00 00 00 00 00 00 00 04 00

03:04.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 15
)
Subsystem: D-Link System Inc DFE-580TX
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Step
ping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <tabort - <mabort->SERR- <perr- intx-<br="">Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at 1180 Expansion ROM at d0300000 [disabled]
Capabilities: <access denied="">Kernel modules: sundance
00: 86 11 02 10 17 00 10 02 15 00 00 02 10 20 00 00
10: 81 11 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 11 12 10
30: 00 00 ff ff 50 00 00 00 00 00 00 00 09 01 0a 0a

03:05.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 15
)
Subsystem: D-Link System Inc DFE-580TX
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Step
ping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <tabort - <mabort->SERR- <perr- intx-<br="">Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 1100 Expansion ROM at d0310000 [disabled]
Capabilities: <access denied="">Kernel modules: sundance
00: 86 11 02 10 17 00 10 02 15 00 00 02 10 20 00 00
10: 01 11 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 11 12 10
30: 00 00 ff ff 50 00 00 00 00 00 00 00 0a 01 0a 0a

03:06.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 15
)
Subsystem: D-Link System Inc DFE-580TX
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Step
ping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <tabort - <mabort->SERR- <perr- intx-<br="">Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 1080 Expansion ROM at d0320000 [disabled]
Capabilities: <access denied="">Kernel driver in use: sundance
Kernel modules: sundance
00: 86 11 02 10 17 00 10 02 15 00 00 02 10 20 00 00
10: 81 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 11 12 10
30: 00 00 ff ff 50 00 00 00 00 00 00 00 0b 01 0a 0a

03:07.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 15
)
Subsystem: D-Link System Inc DFE-580TX
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Step
ping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <tabort - <mabort->SERR- <perr- intx-<br="">Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at 1000 Expansion ROM at d0330000 [disabled]
Capabilities: <access denied="">Kernel driver in use: sundance
Kernel modules: sundance
00: 86 11 02 10 17 00 10 02 15 00 00 02 10 20 00 00
10: 01 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 11 12 10
30: 00 00 ff ff 50 00 00 00 00 00 00 00 09 01 0a 0a

and after apply the workaround

02:00.0 PCI bridge: Intel Corporation 21152 PCI-to-PCI Bridge (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B+ DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <tabort- <mabort-="">SERR- <perr- intx-<br="">Latency: 32, Cache Line Size: 64 bytes
Bus: primary=02, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00001000-00001fff
Prefetchable memory behind bridge: 00000000d0300000-00000000d03fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <tabort- <mabort-="" <serr-="" <perr-<br="">BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied="">Kernel modules: shpchp
00: 86 80 52 b1 07 02 90 02 00 00 04 06 10 20 01 00
10: 00 00 00 00 00 00 00 00 02 03 03 00 11 11 80 02
20: f0 ff 00 00 31 d0 31 d0 00 00 00 00 00 00 00 00
30: 00 00 00 00 dc 00 00 00 00 00 00 00 00 00 00 00

03:04.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 15)
Subsystem: D-Link System Inc DFE-580TX
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <tabort- <mabort-="">SERR- <perr- intx-<br="">Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at 1180 Expansion ROM at d0300000 [disabled]
Capabilities: <access denied="">Kernel driver in use: sundance
Kernel modules: sundance
00: 86 11 02 10 17 00 10 02 15 00 00 02 10 20 00 00
10: 81 11 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 11 12 10
30: 00 00 ff ff 50 00 00 00 00 00 00 00 09 01 0a 0a

03:05.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 15)
Subsystem: D-Link System Inc DFE-580TX
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <tabort- <mabort-="">SERR- <perr- intx-<br="">Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 1100 Expansion ROM at d0310000 [disabled]
Capabilities: <access denied="">Kernel driver in use: sundance
Kernel modules: sundance
00: 86 11 02 10 17 00 10 02 15 00 00 02 10 20 00 00
10: 01 11 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 11 12 10
30: 00 00 ff ff 50 00 00 00 00 00 00 00 0a 01 0a 0a

03:06.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 15)
Subsystem: D-Link System Inc DFE-580TX
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <tabort- <mabort-="">SERR- <perr- intx-<br="">Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 1080 Expansion ROM at d0320000 [disabled]
Capabilities: <access denied="">Kernel driver in use: sundance
Kernel modules: sundance
00: 86 11 02 10 17 00 10 02 15 00 00 02 10 20 00 00
10: 81 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 11 12 10
30: 00 00 ff ff 50 00 00 00 00 00 00 00 0b 01 0a 0a

03:07.0 Ethernet controller: D-Link System Inc DL10050 Sundance Ethernet (rev 15)
Subsystem: D-Link System Inc DFE-580TX
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <tabort- <mabort-="">SERR- <perr- intx-<br="">Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at 1000 Expansion ROM at d0330000 [disabled]
Capabilities: <access denied="">Kernel driver in use: sundance
Kernel modules: sundance
00: 86 11 02 10 17 00 10 02 15 00 00 02 10 20 00 00
10: 01 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 11 12 10
30: 00 00 ff ff 50 00 00 00 00 00 00 00 09 01 0a 0a

Sincerely i'm completely lost with this.

Thanks in advance.</access></perr-></tabort-></access></perr-></tabort-></access></perr-></tabort-></access></perr-></tabort-></access></tabort-></perr-></tabort-></access></perr-></mabort-></tabort </access></perr-></mabort-></tabort </access></perr-></mabort-></tabort </access></perr-></mabort-></tabort </access></mabort-></tabort </perr-></mabort-></tabort

wallabybob

Your four port card has a PCI bridge (Intel 21152) between the four NICs and the CPU.

The BIOS is erroneously setting "ISA enable" in the bridge control register of the 21152.

On pfSense there is nothing you can do about the bridge control register value because the problem occurs during startup BEFORE you have any opportunity to correct the value from an application.

Are you running the latest BIOS (version 0154 released March 23, 2012)? The publicly available release notes give no indication the problem is fixed in that version but a search on the Intel web site for 21152 returned three hits including one giving information on the BIOS updates for the DN2800MT board but that page didn't have an obvious reference to the 21152.

The ISA enable bit in the Bridge Control register of the 21154 PCI Bridge is described as follows:

The 21154 supports ISA mode by providing an ISA enable bit in the bridge control register in
configuration space. ISA mode modifies the response of the 21154 inside the I/O address range in
order to support mapping of I/O space in the presence of an ISA bus in the system. This bit only
affects the response of the 21154 when the transaction falls inside the address range defined by the
I/O base and limit address registers, and only when this address also falls inside the first 64KB of I/
O space (address bits <31:16> are 0000h).
When the ISA enable bit is set, the 21154 does not forward downstream any I/O transactions
addressing the top 768 bytes of each aligned 1KB block. Only those transactions addressing the
bottom 256 bytes of an aligned 1KB block inside the base and limit I/O address range are
forwarded downstream. Transactions above the 64KB I/O address boundary are forwarded as
defined by the address range defined by the I/O base and limit registers.
Accordingly, if the ISA enable bit is set, the 21154 forwards upstream those I/O transactions
addressing the top 768 bytes of each aligned 1KB block within the first 64KB of I/O space. The
master enable bit in the command configuration register must also be set to enable upstream
forwarding. All other I/O transactions initiated on the secondary bus are forwarded upstream only
if they fall outside the I/O address range.
When the ISA enable bit is set, devices downstream of the 21154 can have I/O space mapped into
the first 256 bytes of each 1KB chunk below the 64KB boundary, or anywhere in I/O space above
the 64KB boundary.

(I quoted from the 21154 datasheet because in a short search I couldn't find a datasheet for the 21152 and the datasheet for the E7520 chipset included a very similar description, suggesting the ISA enable bit is a "standard" feature of PCI bridges.)

The BIOS sets ISA enable bit in the bridge upstream of the NICs and then assigns two of the NICs i/O addresses above the first 256 (0x100) bytes of a 1K chunk of I/O space (the chunk from 0x1000 to 0x13ff).

stephenw10

My thoughts exactly. BIOS bug. Unusual on an Intel board though.

Maybe possible to reset the NoISA bit and then warm boot? Or perhaps chain boot something that does that.

I would check your BIOS options for anything that may allow you to change to I/O resources assigned to the NICs.

Steve

jmserrano

@wallabybob:

Your four port card has a PCI bridge (Intel 21152) between the four NICs and the CPU.

The BIOS is erroneously setting "ISA enable" in the bridge control register of the 21152.

On pfSense there is nothing you can do about the bridge control register value because the problem occurs during startup BEFORE you have any opportunity to correct the value from an application.

Are you running the latest BIOS (version 0154 released March 23, 2012)? The publicly available release notes give no indication the problem is fixed in that version but a search on the Intel web site for 21152 returned three hits including one giving information on the BIOS updates for the DN2800MT board but that page didn't have an obvious reference to the 21152.

The ISA enable bit in the Bridge Control register of the 21154 PCI Bridge is described as follows:

The 21154 supports ISA mode by providing an ISA enable bit in the bridge control register in
configuration space. ISA mode modifies the response of the 21154 inside the I/O address range in
order to support mapping of I/O space in the presence of an ISA bus in the system. This bit only
affects the response of the 21154 when the transaction falls inside the address range defined by the
I/O base and limit address registers, and only when this address also falls inside the first 64KB of I/
O space (address bits <31:16> are 0000h).
When the ISA enable bit is set, the 21154 does not forward downstream any I/O transactions
addressing the top 768 bytes of each aligned 1KB block. Only those transactions addressing the
bottom 256 bytes of an aligned 1KB block inside the base and limit I/O address range are
forwarded downstream. Transactions above the 64KB I/O address boundary are forwarded as
defined by the address range defined by the I/O base and limit registers.
Accordingly, if the ISA enable bit is set, the 21154 forwards upstream those I/O transactions
addressing the top 768 bytes of each aligned 1KB block within the first 64KB of I/O space. The
master enable bit in the command configuration register must also be set to enable upstream
forwarding. All other I/O transactions initiated on the secondary bus are forwarded upstream only
if they fall outside the I/O address range.
When the ISA enable bit is set, devices downstream of the 21154 can have I/O space mapped into
the first 256 bytes of each 1KB chunk below the 64KB boundary, or anywhere in I/O space above
the 64KB boundary.

(I quoted from the 21154 datasheet because in a short search I couldn't find a datasheet for the 21152 and the datasheet for the E7520 chipset included a very similar description, suggesting the ISA enable bit is a "standard" feature of PCI bridges.)

The BIOS sets ISA enable bit in the bridge upstream of the NICs and then assigns two of the NICs i/O addresses above the first 256 (0x100) bytes of a 1K chunk of I/O space (the chunk from 0x1000 to 0x13ff).

I'm running the lates bios (version 0072 released 08/08/2012), but there's no difference.

Is there anyway to change ISA+ bit on boot?

maybe with a custom kernel?

Thanks in advance

stephenw10

Check your bios. There isn't a specific guide that I could see but some Intel bioses have this:
@Intel:

ISA Enable Bit • Enabled/Disabled Some older expansion devices require this to be enabled.

Worth a try.

Steve

Edit: More detail than Intels glossary:
@http://www.techarp.com/showfreebog.aspx?lang=0&bogno=100:

ISA Enable Bit

Common Options : Enabled, Disabled

Quick Review

This BIOS feature allows you to determine if the system controller will perform ISA aliasing to prevent conflicts between ISA devices.

The default setting of Enabled forces the system controller to alias ISA addresses using address bits [15:10]. This restricts all 16-bit addressing devices to a maximum contiguous I/O space of 256 bytes.

When disabled, the system controller will not perform any ISA aliasing and all 16 address lines can be used for I/O address space decoding. This gives 16-bit addressing devices access to the full 64KB I/O space.

It is recommended that you disable ISA Enable Bit for optimal AGP (and PCI) performance. It will also prevent your AGP or PCI cards from conflicting with your ISA cards. Enable it only if you have ISA devices that are conflicting with each other.

jmserrano

@stephenw10:

Check your bios. There isn't a specific guide that I could see but some Intel bioses have this:
@Intel:

ISA Enable Bit • Enabled/Disabled Some older expansion devices require this to be enabled.

Worth a try.

Steve

Edit: More detail than Intels glossary:
@http://www.techarp.com/showfreebog.aspx?lang=0&bogno=100:

ISA Enable Bit

Common Options : Enabled, Disabled

Quick Review

This BIOS feature allows you to determine if the system controller will perform ISA aliasing to prevent conflicts between ISA devices.

The default setting of Enabled forces the system controller to alias ISA addresses using address bits [15:10]. This restricts all 16-bit addressing devices to a maximum contiguous I/O space of 256 bytes.

When disabled, the system controller will not perform any ISA aliasing and all 16 address lines can be used for I/O address space decoding. This gives 16-bit addressing devices access to the full 64KB I/O space.

It is recommended that you disable ISA Enable Bit for optimal AGP (and PCI) performance. It will also prevent your AGP or PCI cards from conflicting with your ISA cards. Enable it only if you have ISA devices that are conflicting with each other.

No such option exists.

Thanks

stephenw10

If you boot into Ubuntu and issue the workaround does that enable all the ports? I'm strugling to see how it could.
Looking into this there are other similar threads about e.g.:
http://forums.freebsd.org/showthread.php?t=27611

If pciconf doesn't work for some reason, it didn't appear to for you earlier, you can install lspci and setpci:

pkg_add -r http://ftp-archive.freebsd.org/pub/FreeBSD-Archive/old-releases/i386/8.1-RELEASE/packages/Latest/pciutils.tbz
rehash

I can't see how this would make any difference but maybe worth a shot.

Steve

stephenw10

Just spotted a pretty fundamental typo! :-[
[quote author=stephenw10 link=topic=54066.msg289161#msg289161 date=1348669111]
Could be no difference but it looks like you have missed a : in your pciconf test. It should be:

pciconf -rb pci0:0:2:0: 0x3e

The command should actually be:

pciconf -rb pci0:2:0:0: 0x3e

None of us spotted that 2 in the wrong place. See if you can read the correct bit with that before anything else.

Steve

stephenw10

Here is another user struggling with the same problem. This thread (translated from Czech) has a possible workaround:
http://translate.google.co.uk/translate?hl=en&sl=cs&u=http://www.freebsd.cz/listserv/archive/users-l/2011q4/026764.html

Workaround is to modify the pci-pci driver to reset the noisa bit when it loads. However can that be loaded as a kernel module? Otherwise you would have to recompile the kernel. :-\

But as a hack that there is not such a problem FIXME:

Driver PCI-PCI bridge is sys / dev / pci / pci_pci.c

In it is a key feature pcib_attach_common ()

Well, you have to put it in a suitable place data sequence:

pci_write_config (dev, PCIR_BRIDGECTL_1,
sc-> bridgectl PCIB_BCR_ISA_ENABLE & ~, 2);
sc-> bridgectl pci_read_config = (dev, PCIR_BRIDGECTL_1, 2);

What is the "proper place" is concerned - there you will find the "case" escaped note
"Quirk handling" where he solves individual specifics chip
(Identified by devid).

Steve

jmserrano

@stephenw10:

Just spotted a pretty fundamental typo! :-[
[quote author=stephenw10 link=topic=54066.msg289161#msg289161 date=1348669111]
Could be no difference but it looks like you have missed a : in your pciconf test. It should be:
pciconf -rb pci0:0:2:0: 0x3e

The command should actually be:

pciconf -rb pci0:2:0:0: 0x3e

None of us spotted that 2 in the wrong place. See if you can read the correct bit with that before anything else.

Steve

Corrected the typo, this is the result

pciconf -rb pci0:2:0:0: 0x3e

returns 04

I can change (i suppose disable NOISA bit) with

pciconf -wb pci0:2:0:0: 0x3e 0

and

pciconf -rb pci0:2:0:0: 0x3e

now returns 00

pciconf works perfectly (in thread http://forums.freebsd.org/showthread.php?t=27611, there's an error in the address, it must be hexadecimal)

In ubuntu, after the hack, all ports are enabled (i need to reload sundance module).

Now, the question is:

can i do such opperation in pfsense (reload ste module)? or
can i do pciconf -wb … at boot time?

thanks in advance

stephenw10

As mentioned in the Czech freebsd thread it's not possible to unload/reload the ste driver because it's compiled into the kernel.
You would have to compile a new kernel without it. Probably not worth it!
It is possible to load some kernel modules at boot to override the in kernel version. However I've not seen the pci_pci driver as a module, I don't know if it's possible.

Steve

jmserrano

@stephenw10:

As mentioned in the Czech freebsd thread it's not possible to unload/reload the ste driver because it's compiled into the kernel.
You would have to compile a new kernel without it. Probably not worth it!
It is possible to load some kernel modules at boot to override the in kernel version. However I've not seen the pci_pci driver as a module, I don't know if it's possible.

Steve

Last chance.

Is there anyway to run the command "pciconf -wb …" at boot time.

Thanks again

stephenw10

Nope. You couldn't run that until after the bridge has been detected and then it's too late. You have a few options as I see it:
You could try to reload the ste(4) driver somehow though I don't know how.
You could try to patch the pci_pci driver and load it as a kernel module.
You could hack the BIOS to stop it setting the noisa bit. Not as difficult as you might think but risky.

Steve

wallabybob

Another option is to report the problem to Intel and ask for a BIOS update.

I suspect, not having written any kernel modules to behave this way, that it might be possible to write a kernel module to be loaded at boot time, run before the PCI device tree is walked and fixup the bridge register. Send me a message if you would like to discuss incentives that would persuade me to attempt it.