NEW Package: freeRADIUS 2.x

Nachtfalke

Hi itbit,
Hi marcello,

I am going to be on holliday the next two weeks. I don't want to add some code which could (but probably will not) cause a problem with the package. If you are able to do some tests please feel free to add these changes to the package on github. I think the both options - change the timeout value and to disable/enable temporarily some hosts will be a good improvement.

Thanks for your help!

itbit

Hi Nachtfalke and Marcelloc,

I have updated both freeradius.inc and freeradiussync.xml to allow the modification of the default XMLRPC timeout from the GUI
I also added the checkbox option for selecting to which servers we want to sync

both files have been attached to this post.

I also tried (but failed) to include an option to specify the user name for the account that will sync because in some of my Pfesnses I changed the default username from 'admin' to something else
but it works out that 'admin' is hardcoded in several places including xmlrpc.inc…

hopefully this all looks right to you, so far I have tested and is working as expected.

Cheers,

freeradius.inc.txt
freeradiussync.xml.txt

marcelloc

itbit,

push it via github.

It will be easier to check changes and commit on current code.

https://github.com/bsdperimeter/pfsense-packages

itbit

Well… It took me a bit to figure it out
but I think I got it.
i proposed the changes at
https://github.com/bsdperimeter/pfsense-packages/tree/master/config/freeradius2

Cheers,

Nachtfalke

Updates pkg v1.6.6_4:

Added: Possibility to edit the timeout when doing an XMLRPC sync between different RADIUS servers. If one RADIUS Server does not respond the main pfsense does not respond until the default timeout of 150s is over.
Added: Possibility to endable/disable a host when doing an XMLRPC sync. This allows you to add all destination hosts you want to sync this but if one is down or you do not want to sync the changes to this host you can disable this host for sync.

Thank you itbit for adding this code and these options to the package. :-)

Known bugs:

When using "stop/start accounting on CP then "Amount of Time/Amount of Traffic" isn't working correctly.
http://redmine.pfsense.org/issues/2164
When using CP + RADIUS + Vouchers and "reauthenticate every minute" is enabled then CP sends the voucher as username to RADIUS. This causes RADIUS to disconnect the "user/voucher" because of an unknown/wrong "username".
http://redmine.pfsense.org/issues/2155
When stop/start accounting on CP is enabled than the syslog shows many "wrong order" or "Login found bot no logout detected". This seems to not affect the usage of RADIUS but it is not 100% correct.
http://redmine.pfsense.org/issues/2143

DestekTeknik

Dear friends,

I have a stupid question to ask. I've searched on the forum but couldn't find an exact solution to my problem.

I'm modifying the files of FR 2 to make it connect to my mysql server and work flawlessly with my daloradius server. I'm backing up the files I've modified, but the problem is, whenever I reboot the machine, all of the files returns to their original values. So I made a backup of the raddb folder, and whenever I reboot my pfsense, I stop the service, untar the backup I've made, and restart the service.

I want to get rid all of that. Is there any way to make the file changes permanent?

marcelloc

@DestekTeknik:

I want to get rid all of that. Is there any way to make the file changes permanent?

Edit script that creates config files, it's usually package_name.inc script.

And to keep this file modification on xml backup, use filer package.

Nachtfalke

@DestekTeknik
All files that will be modified by the GUI are in the freeradius.inc:

/usr/local/pkg/freeradius.inc

So the best solution for you would be to modify the freeradius.inc file so that it does what you want.
Then your configuration will survive a reboot :-)

But it will not survive a package reinstallation of freeradius and not a pfsense firmware update.
For this - if I understand marcelloc correctly - you will have a look at the filer package. I didn't ever used the filer package.

anzak84

After Updates pkg v1.6.6_4:

radiusd -X
rlm_eap: SSL error error:02001002:system library:fopen:No such file or directory
rlm_eap_tls: Error reading certificate file /usr/local/etc/raddb/certs/server_cert.pem
rlm_eap: Failed to initialize type tls
/usr/local/etc/raddb/eap.conf[2]: Instantiation failed for module "eap"
/usr/local/etc/raddb/sites-enabled/default[339]: Failed to load module "eap".
/usr/local/etc/raddb/sites-enabled/default[274]: Errors parsing authenticate section.

radiusd.conf

modules {
$INCLUDE ${confdir}/modules/
#$INCLUDE eap.conf
…...........
#$INCLUDE sites-enabled/
…..............

radiusd -X

radiusd: #### Loading Virtual Servers ####
server { # from file /usr/local/etc/raddb/radiusd.conf
modules {
} # modules
} # server
radiusd: #### Opening IP addresses and Ports ####
listen {
type = "auth"
ipaddr = 192.168.65.254
port = 1812
Failed binding to authentication address 192.168.65.254 port 1812: Address already in use
/usr/local/etc/raddb/radiusd.conf[36]: Error binding to port for 192.168.65.254 port 1812

and

radtest test test 127.0.0.1:1812 0 test

Sending Access-Request of id 226 to 127.0.0.1 port 1812
User-Name = "test"
User-Password = "test"
NAS-IP-Address = 192.168.65.254
NAS-Port = 0
Message-Authenticator = 0x00000000000000000000000000000000
radclient: no response from server for ID 226 socket 3

how to solve the problem. FreeRadius removal and reinstallation does not help: (

RADIUS NAS IP attribute change to 192.168.65.254. Working.

Nachtfalke

After reinstalling freeradius go to the EAP tab and check if the certificates are correct and then click again on "save".
It could also help to change the "cert manager" option on the EAP-tab, click save and then change back and click save again.

Nachtfalke

New version of freeradius is available:
2.2.0

When looking at the freeradius.org webpage it says:

100% configuration file compatible with 2.1.x. The only fix needed is to disallow "hashsize=0" for rlm_passwd

So this should be no problem for the configuration.

But the makefile seems to have changed - and now different "build options" must be used. Can someone verify this and perhaps make it available for pfsense ?
http://www.freebsd.org/cgi/cvsweb.cgi/ports/net/freeradius2/
http://www.freebsd.org/cgi/cvsweb.cgi/ports/net/freeradius2/Makefile?rev=1.108

Thanks

oragon

newbie question. i have reinstalled my pfsense 2.0.1 for 3 times but i don't see the freeradius 2.x as my available package. please advise on how i could have it. thanks for the reply

marcelloc

you have nano or full install????

Nachtfalke

In general freeradius2 package is available for i386/amd64 installations using pfsense version 2.x
Full installation on HDD is supported and it should run on nanobsd installations, too.

Not sure, why it will not be displayed on you installation but you can try this:
1.) login on pfsense
2.) access this URL: http://your_pfsense_IP/pkg_mgr_install.php?id=freeradius2

z3r0tech

@Nachtfalke:

In general freeradius2 package is available for i386/amd64 installations using pfsense version 2.x
Full installation on HDD is supported and it should run on nanobsd installations, too.

Not sure, why it will not be displayed on you installation but you can try this:
1.) login on pfsense
2.) access this URL: http://your_pfsense_IP/pkg_mgr_install.php?id=freeradius2

this is my pfsense:

2.0.1-RELEASE (i386)
built on Mon Dec 12 17:53:52 EST 2011
FreeBSD 8.1-RELEASE-p6

You are on the latest version.

im using the http://mirror.optus.net/pub/pfSense/downloads/pfSense-2.0.1-RELEASE-i386.iso.gz
installed everything on my hdd using vmware workstation 8
installed lusca and squidguard without problems…

i have the same problem it does not show on available packages
here's the error on console when i try pkg_add -r freeradius2
and manual adding it on the pfsense webgui

is there a way i can fetch it or modify the repo links or xml? how?
or how can i install it manually or add it on the available package list?

![console freeradius2.jpg](/public/imported_attachments/1/console freeradius2.jpg)
![console freeradius2.jpg_thumb](/public/imported_attachments/1/console freeradius2.jpg_thumb)

Nachtfalke

I have some different VMs with 2.0.1 x86/x64 installs and pfsense 2.1 installs.
I can install the package on all machines from the GUI.

The parameter which indicates the version is the same as for lets say squid2 or squidguard:


<required_version>2.0</required_version>

But I am not sure where the check is for the different installation types like CD, nanobsd and embedded :(

Can you try another .iso image from another mirror ?

z3r0tech

@Nachtfalke:

I have some different VMs with 2.0.1 x86/x64 installs and pfsense 2.1 installs.
I can install the package on all machines from the GUI.

The parameter which indicates the version is the same as for lets say squid2 or squidguard:
<required_version>2.0</required_version>
But I am not sure where the check is for the different installation types like CD, nanobsd and embedded :(

Can you try another .iso image from another mirror ?

the url is invalid i found it here https://redmine.pfsense.org/issues/2075
https://redmine.pfsense.org/projects/pfsense/repository/revisions/c70452506a0ab84a9d72547656b516f6e61578da
i don't know how to apply the diff this is the fix…

Nachtfalke

That's not the problem why you do not get freeradius in packagemanager GUI.

If you want to use pkg_add -r then just use the complete path to pfsense server.

x86:
pkg_add -r http://files.pfsense.org/packages/8/All/freeradius-2.1.12_1.tbz

x64:
pkg_add -r http://files.pfsense.org/packages/amd64/8/All/freeradius-2.1.12_1.tbz

z3r0tech

@Nachtfalke:

That's not the problem why you do not get freeradius in packagemanager GUI.

If you want to use pkg_add -r then just use the complete path to pfsense server.

x86:
pkg_add -r http://files.pfsense.org/packages/8/All/freeradius-2.1.12_1.tbz

x64:
pkg_add -r http://files.pfsense.org/packages/amd64/8/All/freeradius-2.1.12_1.tbz

thanks! it's working now…

i tried this post to install the gui: http://forum.pfsense.org/index.php?topic=50572.0
Fatal error: Call to undefined function freeradius_install_command() in /usr/local/www/exec.php(244) : eval()'d code on line 9

any solutions?

basterik

hi all! culd any one help me to config xmlrpc sync? i print gui ip adress, password, but sync does't done