New 1u build - NIC not working?
-
I was able to connect my PC to the integrated NIC and access the web console and enable SSH. The same cable won't work on the Dell X3959 PRO/1000 Dual Port Server NIC. Here are the results of the commands. I manually set the IP addresses so I could test the cables.
em0@pci0:1:0:0: class=0x020000 card=0x135e8086 chip=0x105e8086 rev=0x06 hdr=0x00 class = network subclass = ethernet em1@pci0:1:0:1: class=0x020000 card=0x135e8086 chip=0x105e8086 rev=0x06 hdr=0x00 class = network subclass = ethernet re0@pci0:3:0:0: class=0x020000 card=0x0d7a105b chip=0x816810ec rev=0x02 hdr=0x00 class = network subclass = ethernet [2.0.1-RELEASE][admin@pfSense.localdomain]/root(2): ifconfig -a em0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500 options=9b <rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum>ether 00:15:17:76:38:c4 inet6 fe80::215:17ff:fe76:38c4%em0 prefixlen 64 scopeid 0x1 inet 10.0.0.60 netmask 0xffffffff broadcast 10.0.0.60 nd6 options=3 <performnud,accept_rtadv>media: Ethernet autoselect status: no carrier em1: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500 options=19b <rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum,tso4>ether 00:15:17:76:38:c5 inet6 fe80::215:17ff:fe76:38c5%em1 prefixlen 64 scopeid 0x2 nd6 options=3 <performnud,accept_rtadv>media: Ethernet autoselect status: no carrier re0: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500 options=389b <rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum,wol_ucast,wol_mcast,wol_magic>ether d0:27:88:d2:93:0e inet6 fe80::d227:88ff:fed2:930e%re0 prefixlen 64 scopeid 0x3 inet 10.0.0.50 netmask 0xffffff00 broadcast 10.0.0.255 nd6 options=3 <performnud,accept_rtadv>media: Ethernet autoselect (1000baseT <full-duplex>) status: active pflog0: flags=100 <promisc>metric 0 mtu 33664 pfsync0: flags=0<> metric 0 mtu 1460 syncpeer: 224.0.0.240 maxupd: 128 syncok: 1 enc0: flags=0<> metric 0 mtu 1536 lo0: flags=8049 <up,loopback,running,multicast>metric 0 mtu 16384 options=3 <rxcsum,txcsum>inet 127.0.0.1 netmask 0xff000000 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x7 nd6 options=3 <performnud,accept_rtadv>re0_vlan35: flags=8843 <up,broadcast,running,simplex,multicast>metric 0 mtu 1500 options=3 <rxcsum,txcsum>ether d0:27:88:d2:93:0e inet6 fe80::215:17ff:fe76:38c4%re0_vlan35 prefixlen 64 scopeid 0x8 nd6 options=3 <performnud,accept_rtadv>media: Ethernet autoselect (1000baseT <full-duplex>) status: active vlan: 35 parent interface: re0</full-duplex></performnud,accept_rtadv></rxcsum,txcsum></up,broadcast,running,simplex,multicast></performnud,accept_rtadv></rxcsum,txcsum></up,loopback,running,multicast></promisc></full-duplex></performnud,accept_rtadv></rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum,wol_ucast,wol_mcast,wol_magic></up,broadcast,running,simplex,multicast></performnud,accept_rtadv></rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum,tso4></up,broadcast,running,simplex,multicast></performnud,accept_rtadv></rxcsum,txcsum,vlan_mtu,vlan_hwtagging,vlan_hwcsum></up,broadcast,running,simplex,multicast>
-
Your subnet mask on em0 is /32 so it cannot reply to pings. It's also in the same subnet as re0 so that's gonna screw with routing.
Change it to, for example, 10.0.10.60/24.When you ran those commands what did you have connected to each NIC?
Steve
-
I had a cable going from my PC to the re0 port on the new box and nothing connected to the ports on the Intel NIC. I'll change the subnet mask and try again. Both NICs being on the same subnet was just a test. I have tried under other configurations.
-
I changed the subnet mask to /24 and still no luck. The next steps are to test the NIC in another machine and test another NIC in this machine. Hopefully I'll come up with something.
-
Are getting any link/speed leds on the Intel NICs?
A good test would be to connect them both up to a switch or something and run ifconfig again. Look to see if the status is active and that the media type has negotiated correctly.Steve
-
Both indicator lights on the ports are active with a cable plugged in. The NIC is set to auto negotiate but it looks like they aren't negotiating properly and they don't activate. I will continue testing.
-
If you only changed the mask, you didn't fix the big underlying problem there - you can't have two NICs on the same subnet. That's at least part of your problem if not all of it.
-
@KM:
it looks like they aren't negotiating properly and they don't activate.
I don't know what you mean by "don't activate". status shown by ifconfig doesn't go to Active?
You won't get any communication through the NIC until the NIC status changes to active.
-
I changed the IP addresses so they are all on different subnets. What I mean by they don't activate is that the status in ifconfig doesn't change to active. I'm going to try a known working NIC in the box to verify but I think the NIC is just bad. I'll let you know what I find out.
-
I tested another NIC and it worked so I ordered another dual port server nic. Thanks for all the help folks!
-
So, I ordered another dual port server NIC (Intel Pro/1000 PCIe x4) and tried to get it working to no avail. Now I have two dual port NICs (not a problem because I can always find a use for these things) that aren't working in this box but a single port Intel desktop NIC that will. I would really like this box to have two LAN interfaces so I can do some DMZ stuff but at this point I may have to run a single port.
Any suggestions?
-
-
I purchased a new one and plugged it the same way as the first one. The cards are both detected but there is no connection.
-
Also, I should mention that I have since been able to get the card working with Ubuntu server which can detect and use all three interfaces (built in motherboard NIC).
-
@KM:
Also, I should mention that I have since been able to get the card working with Ubuntu server which can detect and use all three interfaces (built in motherboard NIC).
Please post the output of pfSense shell commands```
ifconfig ; /etc/rc.banner
I presume you have fixed the configuration problem previously discussed. Please give more information than "there is no connection". What did you attempt? What was reported? What did you expect to be reported?
-
Sorry I haven't replied sooner.. work has been pushing for crazy overtime. I did fix the previous config issue but in the end a reinstall of pfSense fixed the issue. I have no idea why but I have a working box now. I'll post pics of the build when a get a minute to breath.
Thanks for all your help everyone!