Quagga not connecting to other routers

heper

could you provide us with some screenshot of all your quagga configuration tabs ?
if you've assigned interfaces to your openvpn tunnel, make sure you set type to 'none' & restart the tunnels

other then that i'm not sure what could be the problem, i have multiple sites with dynamic routing using quagga without issues.

hans-d

The Quagga screens from the server side.

Client is almost identical, except:

router id: has a different router id
no addtional routes (yet)
different interface (the openvpn client is choosen there)

screenshot.1.jpg
screenshot.1.jpg_thumb

hans-d

2nd tab

screenshot.2.jpg
screenshot.2.jpg_thumb
screenshot.3.jpg
screenshot.3.jpg_thumb

heper

only differences i see with my configurations are the following:

-my area is not an ip address (don't know what the limitations are). Try setting the area to 0.0.0.1
-i've filled in the metric @ interface config
-i've a description filled in @ interface config
-my openvpn server/clients are assigned as physical interface (interfaces–>assign). But ive been told by jimp or cmb that this is no longer a requirement when using quagga, so it shouldn't matter

i hope one of these solves your problems, altho i somewhat doubt they will.

hans-d

Here the current routes (first is the client, second is the server).

Tried the description and other area, no luck so far.

screenshot.1.jpg
screenshot.1.jpg_thumb
screenshot.2.jpg
screenshot.2.jpg_thumb

heper

there are only a few basic requirements for quagga to work:

-tunnel endpoints must be able to reach each other
-firewall rules must allow ospf traffic

it has allways worked for me. probably some small thing we're missing to get your setup working

hans-d

Thanks for helping me think this through.
Seems I got all the point covered, but there must be a missing link (pun intended).

Quagga status Server

Area ID: 0.0.0.1
Shortcutting mode: Default, S-bit consensus: ok
Number of interfaces in this area: Total: 2, Active: 2
Number of fully adjacent neighbors in this area: 0
Area has no authentication
Number of full virtual adjacencies going through this area: 0
OSPF Router with ID (192.168.10.254)

Router Link States (Area 0.0.0.1)

Link ID ADV Router Age Seq# CkSum Link count
192.168.10.254 192.168.10.254 2 0x80000002 0x3cc9 2

Codes: K - kernel route, C - connected, S - static, R - RIP, O - OSPF,
I - ISIS, B - BGP, > - selected route, * - FIB route

K>* 0.0.0.0/0 via 194.xxx.xxx.xxx, re0
C>* 127.0.0.0/8 is directly connected, lo0
K>* 172.20.2.0/24 via 172.21.12.2, ovpns4
K>* 172.21.4.0/22 via 172.21.4.2, ovpns2
C>* 172.21.4.2/32 is directly connected, ovpns2
C>* 172.21.8.2/32 is directly connected, ovpns3
K>* 172.21.12.0/22 via 172.21.12.2, ovpns4
O 172.21.12.2/32 [110/10] is directly connected, ovpns4, 00:00:02
C>* 172.21.12.2/32 is directly connected, ovpns4
C>* 192.168.8.0/23 is directly connected, em1
O 192.168.10.0/24 [110/10] is directly connected, em1, 00:00:02
C>* 192.168.10.0/24 is directly connected, em1
C>* 192.168.11.0/24 is directly connected, em1
C>* 192.168.12.0/22 is directly connected, em2
C>* 192.168.178.0/24 is directly connected, em3
C>* 194.xxx.xxx.xxx/29 is directly connected, re0
C>* 194.xxx.xxx.xxx/32 is directly connected, re0
K>* 194.xxx.xxx.xxx/32 via 192.168.178.1, em3
K>* 194.xxx.xxx.xxx/32 via 194.xxx.xxx.xxx, re0
K>* 194.xxx.xxx.xxx/32 via 194.xxx.xxx.xxx, re0
K>* 208.67.220.220/32 via 192.168.178.1, em3
K>* 208.67.222.222/32 via xxx.xxx.xxx, re0

(em3 and re0 are both wan)

em1 is up (= lan 1)
ifindex 2, MTU 1500 bytes, BW 0 Kbit <up,broadcast,running,promisc,simplex,multicast>Internet Address 192.168.10.254/24, Broadcast 192.168.10.255, Area 0.0.0.1
MTU mismatch detection:enabled
Router ID 192.168.10.254, Network Type BROADCAST, Cost: 10
Transmit Delay is 1 sec, State Waiting, Priority 1
No designated router on this network
No backup designated router on this network
Multicast group memberships: OSPFAllRouters
Timer intervals configured, Hello 10s, Dead 40s, Wait 40s, Retransmit 5
Hello due in 7.921s
Neighbor Count is 0, Adjacent neighbor count is 0
ovpns4 is up (=openvpn server)
ifindex 14, MTU 1500 bytes, BW 0 Kbit <up,pointopoint,running,multicast>Internet Address 172.21.12.1/32, Peer 172.21.12.2, Area 0.0.0.1
MTU mismatch detection:enabled
Router ID 192.168.10.254, Network Type POINTOPOINT, Cost: 10
Transmit Delay is 1 sec, State Point-To-Point, Priority 1
No designated router on this network
No backup designated router on this network
Multicast group memberships: OSPFAllRouters
Timer intervals configured, Hello 10s, Dead 40s, Wait 40s, Retransmit 5
Hello due in 7.921s
Neighbor Count is 0, Adjacent neighbor count is 0

Quagga on client

ovpns4 is up
ifindex 14, MTU 1500 bytes, BW 0 Kbit <up,pointopoint,running,multicast>Internet Address 172.21.12.1/32, Peer 172.21.12.2, Area 0.0.0.1
MTU mismatch detection:enabled
Router ID 192.168.10.254, Network Type POINTOPOINT, Cost: 10
Transmit Delay is 1 sec, State Point-To-Point, Priority 1
No designated router on this network
No backup designated router on this network
Multicast group memberships: OSPFAllRouters
Timer intervals configured, Hello 10s, Dead 40s, Wait 40s, Retransmit 5
Hello due in 7.921s
Neighbor Count is 0, Adjacent neighbor count is 0
OSPF Router with ID (172.20.2.254)

Router Link States (Area 0.0.0.1)

Link ID ADV Router Age Seq# CkSum Link count
172.20.2.254 172.20.2.254 421 0x80000004 0xe62c 2

Codes: K - kernel route, C - connected, S - static, R - RIP, O - OSPF,
I - ISIS, B - BGP, > - selected route, * - FIB route

K>* 0.0.0.0/0 via 192.168.2.254, em0
K>* 8.8.8.8/32 via 192.168.2.254, em0
C>* 127.0.0.0/8 is directly connected, lo0
O 172.20.2.0/24 [110/10] is directly connected, em1, 00:07:41
C>* 172.20.2.0/24 is directly connected, em1
K>* 172.21.12.1/32 via 172.21.12.5, ovpnc4
O 172.21.12.5/32 [110/10] is directly connected, ovpnc4, 00:07:41
C>* 172.21.12.5/32 is directly connected, ovpnc4
C>* 192.168.2.0/24 is directly connected, em0
K>* 192.168.10.0/24 via 172.21.12.5, ovpnc4
K>* 208.67.222.222/32 via 192.168.2.254, em0

em0 = wan

em1 is up
ifindex 2, MTU 1500 bytes, BW 0 Kbit <up,broadcast,running,simplex,multicast>Internet Address 172.20.2.254/24, Broadcast 172.20.2.255, Area 0.0.0.1
MTU mismatch detection:enabled
Router ID 172.20.2.254, Network Type BROADCAST, Cost: 10
Transmit Delay is 1 sec, State DR, Priority 1
Designated Router (ID) 172.20.2.254, Interface Address 172.20.2.254
No backup designated router on this network
Multicast group memberships: OSPFAllRouters OSPFDesignatedRouters
Timer intervals configured, Hello 10s, Dead 40s, Wait 40s, Retransmit 5
Hello due in 9.275s
Neighbor Count is 0, Adjacent neighbor count is 0

ovpnc4 is up
ifindex 8, MTU 1500 bytes, BW 0 Kbit <up,pointopoint,running,multicast>Internet Address 172.21.12.6/32, Peer 172.21.12.5, Area 0.0.0.1
MTU mismatch detection:enabled
Router ID 172.20.2.254, Network Type POINTOPOINT, Cost: 10
Transmit Delay is 1 sec, State Point-To-Point, Priority 1
No designated router on this network
No backup designated router on this network
Multicast group memberships: OSPFAllRouters
Timer intervals configured, Hello 10s, Dead 2s, Wait 2s, Retransmit 5
Hello due in 9.275s
Neighbor Count is 0, Adjacent neighbor count is 0

Firewall

On openvpn tab:

ID Proto Source Port Destination Port Gateway Queue Schedule Description

- - - - none allow all</up,pointopoint,running,multicast></up,broadcast,running,simplex,multicast></up,pointopoint,running,multicast></up,pointopoint,running,multicast></up,broadcast,running,promisc,simplex,multicast>

hans-d

assigning vpn server / client to interfaces did not work.

on server side I can see in pftop:
ospf I 172.21.12.6:0 224.0.0.5:0
ospf O 172.21.12.1:0 224.0.0.5:0

on the client side I can see in pftop
ospf O 172.21.12.6:0 224.0.0.5:0
ospf I 172.21.12.1:0 224.0.0.5:0

Doing a trace on 172.21.12.6 on both sides gets me on both sides
172.21.12.6 > 224.0.0.5: OSPFv2, Hello, length 44
Router-ID 172.20.2.254, Area 0.0.0.1, Authentication Type: none (0)
Options [External]
Hello Timer 10s, Dead Timer 40s, Mask 0.0.0.0, Priority 1

And a trace on 172.2.12.1 gets me on both sides:
172.21.12.1 > 224.0.0.5: OSPFv2, Hello, length 44
Router-ID 192.168.10.254, Area 0.0.0.1, Authentication Type: none (0)
Options [External]
Hello Timer 10s, Dead Timer 40s, Mask 0.0.0.0, Priority 1

So data is coming through on both ends, but somehow Quagga doesn't respond

heper

i've been wondering ….

how have you been adding routes for you openvpn connection ?

also i just noticed```
172.21.12.6 > 224.0.0.5: OSPFv2, Hello, length 44

192.168.222.1 > 224.0.0.5: OSPFv2, Hello, length 48
Router-ID 10.10.10.1, Area 0.0.0.1, Authentication Type: none (0)
Options [External]
Hello Timer 10s, Dead Timer 40s, Mask 255.255.255.255, Priority 1
Neighbor List:
10.0.0.1

hans-d

My vpn server settings:

peer-to-peer ssl/tls
udp
tun
interface LAN (portforwarded from two WAN)
Tunnel: 172.21.12.0/22
Local network: 192.168.10.0/24 *
Remote network: 172.20.2.0/24 *
nothing with advanced

Client specific override:

iroute 172.20.2.0 255.255.255.0; *

Open vpn client:

tunnel network: left empty
remote network: left empty
nothing with advanced

Needed to work on both lans (prior to quagga)

No additional routes entered anywhere else

heper

could you do me a favor and fill in the tunnel network on the client side ?

restart ovpn & quagga afterwards to be sure

hans-d

I've setup a additional testbox to have two boxes that could be easily reset without disrupting the normal users.
I've now got it working on these test machines by adding tunnel and remote on the vpn client configuration.