Error message
-
I am running this on a msata drive with a intel DN2800MT mobo 1 on board intel gig nic and 1 pcie gig nic
i have the nanobsd 4g file on my usb key which i then zcat over to my msata drive and then reboot
The drive passes all tests and shows no other error and pfsense works great other then this issue which i can't explain.
Any other suggestion or ideas are definitely welcome and thanks.
-
Are you sure the 4GB mSATA is actually 4GB?
If it's working otherwise, I'd try it again with a 2GB image.
If the drive is too small and the image file is bigger than the drive, it would explain the missing cf slice.
As it is, if you upgrade the firmware you'd lose your config in the process because it's not being stored in the correct place on the disk.
-
The msata is a 30 gig drive and is pretty much brand new.
I have secure erased it in pmagic prior to zcat the image over.
I just tried again with most recent image and still get the same error as it boots up for the first time.
Anything else I could try ? Much appreciated and thanks.
-
Please post the output of pfSense shell commands:```
more /etc/fstab
sysctl kern.disks
ls /dev/ad*
mount -
as per your request:
$ more /etc/fstab /dev/ufs/pfsense0 / ufs ro,sync,noatime 1 1 /dev/ufs/cf /cf ufs ro,sync,noatime 1 1 $ sysctl kern.disks kern.disks: ad6 $ ls /dev/ad* /dev/ad6 /dev/ad6a $ mount /dev/ufs/pfsense0 on / (ufs, local, noatime, synchronous) devfs on /dev (devfs, local) /dev/md0 on /tmp (ufs, local) /dev/md1 on /var (ufs, local) devfs on /var/dhcpd/dev (devfs, local) -
What about:
ls -l /dev/ufsOn a properly formatted NanoBSD image, it should look like:
: ls -l /dev/ufs total 0 crw-r----- 1 root operator 0, 63 Jan 4 21:02 cf crw-r----- 1 root operator 0, 65 Jan 4 21:02 pfsense0 crw-r----- 1 root operator 0, 67 Jan 4 21:02 pfsense1Judging by the fact that you only have /dev/ad6a I'm guessing something is seriously not right with how that was written to the disk. Normally that looks like:
: ls -l /dev/ad* crw-r----- 1 root operator 0, 56 Jan 4 21:02 /dev/ad0 crw-r----- 1 root operator 0, 57 Jan 4 21:02 /dev/ad0s1 crw-r----- 1 root operator 0, 60 Jan 4 21:02 /dev/ad0s1a crw-r----- 1 root operator 0, 58 Jan 4 21:02 /dev/ad0s2 crw-r----- 1 root operator 0, 61 Jan 4 21:02 /dev/ad0s2a crw-r----- 1 root operator 0, 59 Jan 4 21:02 /dev/ad0s3 -
I agree with you 100 %
When i write to the msata – i first zero out the whole drive with parted magic, i then write directly to the card.
"zcat (current name of the current imag) | dd of=/dev/sda bs=16k"
It then indicates it has written 4g nanobsd vga image to msata with no errors. Then i reboot and while its loading for the first time is when i see that error.
Here is the code you asked me to run and you are correct about things not showing as correct.
$ ls -l /dev/ufs total 0 crw-r----- 1 root operator 0, 78 Jan 8 22:41 pfsense0Any suggestions on how this is going wrong? I've tried to remove any variables but still end up here.
Many thanks again for any assistance.
-
What is the exact filename of the 4GB image you used to write that out?
-
latest-nanobsd-vga-4g.img.gz 09-Jan-2013 17:59 86M
-
That is an update slice, not a full nanobsd image.
-
WOW i feel like a complete idiot.. the worst part is i know that i was troubleshooting to far and it was going to be something easy and way obvious…for this i say thank you. I now have it fully installed with
pfSense-2.1-BETA1-4g-amd64-nanobsd_vga-20130109-1617.img.gz 09-Jan-2013 17:59 172M
(2.1-BETA1 (amd64)
built on Wed Jan 9 16:17:18 EST 2013
FreeBSD gho57.localdomain 8.3-RELEASE-p5 FreeBSD 8.3-RELEASE-p5 #0: Wed Jan 9 17:47:08 EST 2013 root@snapshots-8_3-amd64.builders.pfsense.org:/usr/obj./usr/pfSensesrc/src/sys/pfSense_wrap_vga.8.amd64 amd64)
nanobsd (4g)
and running on both slices.But i'm still having issues upgrading either auto update/console update or manual update and on both slices.
It down loads the package it attempts to install but thats as far as it goes.
I log back in and met with a warning message:
php: : New alert found: Something went wrong when trying to update the fstab entry. Aborting upgrade.php: : The command '/usr/local/sbin/gzsig verify /etc/pubkey.pem < '/root/firmware.tgz'' returned exit code '2', the output was 'No gzip signature found Couldn't verify input'I have checked and i do have allow invalid or missing signatures to be used.
Any more help or suggestion would be much appreciated.
Thanks again.
