IPv6 Prefix Delegation broken?

eri--

I pushed some more fixes.
Same you can just recopy interfaces.inc since it contains the changes.

athurdent

Didn't change anything, sorry. Even with latest 6387590fa6dcd90f11154c62ad87c62aec43b1b9
The system acts exactly like described before. I double checked that I am using the newest version of interfaces.inc

Edit: if it helps, from Syslog right after reboot:
php: : Error: cannot open dhcpdv6.conf in services_dhcpdv6_configure().
dhcp6c[19183]: update_ia: T1(2250) and/or T2(3600) is locally determined

phil.davis

Are you on a nanobsd system?
There isn't any call to conf_mount_rw then conf_mount_ro in services_dhcpdv6_configure(). If this routine is called from something that does not already have the file system mounted RW, then trying to write the dhcpdv6.conf will fail. The easy fix would be to put these rw/ro calls either side of the block of code doing the file_put_contents. But ermal might see a better/more appropriate place to do it - I'll leave it to him as I don't have a test system accessible now to play on.

eri--

Pushed another fix its both services.inc and interfaces.inc
Test it out and let me know.

athurdent

Sorry, no changes. Same behaviour as described in http://forum.pfsense.org/index.php/topic,58664.msg314878.html#msg314878

eri--

Can you show me the contents of /tmp/dhcpd.sh?

athurdent

Sure:

cat /tmp/dhcpd.sh
mkdir -p /var/dhcpd
mkdir -p /var/dhcpd/dev
mkdir -p /var/dhcpd/etc
mkdir -p /var/dhcpd/usr/local/sbin
mkdir -p /var/dhcpd/var/db
mkdir -p /var/dhcpd/var/run
mkdir -p /var/dhcpd/usr
mkdir -p /var/dhcpd/lib
mkdir -p /var/dhcpd/run
chown -R dhcpd:_dhcp /var/dhcpd/*
cp /lib/libc.so.* /var/dhcpd/lib/
cp /usr/local/sbin/dhcpd /var/dhcpd/usr/local/sbin/
chmod a+rx /var/dhcpd/usr/local/sbin/dhcpd

eri--

Do you have those directories created?
If you run the script from ssh do you get any errors?

phil.davis

Hmmm - I thought this would be easy to reproduce on nanobsd. But my system comes up OK. On the console at boot:

Starting DHCP service...done.
Starting DHCPv6 service...done.

And the dhcp conf files are there:

-rw-r--r--  1 root  _dhcp  731 Feb 10 18:55 dhcpd.conf
-rw-r--r--  1 root  _dhcp  482 Feb 10 18:55 dhcpdv6.conf

The system boots cleanly, with the filesystem read-only at the end.
On my system, the dhcpdv6.conf must be written at a time when the filesystem is read-write. I don't actually have any DHCPv6 available from my ISP, so I am not getting an IPv6 stuff handed down from upstream to my WAN. Perhaps the asynchronous receipt of IPv6 settings from upstream will trigger a call to services_dhcpdv6_configure() when the filesystem is read-only?
Interesting to see what is different about the startup sequence for arthurdent.

athurdent

After a reboot it looks OK. Everything the script does is done and it does not give any errors running is manually. However If found the following in my system log. There seems to be an error at some point while booting up (like I said before, "lan" is the external interface in my test setup, so "interface: lan" is correct here):

Feb 10 14:45:19 pfsense-alix php: : rc.newwanipv6: Informational is starting vr0.
Feb 10 14:45:24 pfsense-alix php: : rc.newwanipv6: on (IP address: 2001:xxx:xxx:dead:20d:b9ff:fe12:7864) (interface: lan) (real interface: vr0).
Feb 10 14:45:25 pfsense-alix php: : The command '/bin/sh /tmp/dhcpd.sh' returned exit code '127', the output was 'chown: not found mount: not found'
Feb 10 14:45:28 pfsense-alix dhcpleases: kqueue error: unkown
Feb 10 14:45:28 pfsense-alix dhcpleases: Could not deliver signal HUP to process because its pidfile does not exist, No such file or directory.

Ermal, would you like me to PM you the whole log?

eri--

I pushed another fix but yeah system log would be useful.

athurdent

I send the necessary information via PM, hope it arrived.