Openvpn - quagga ospf - mesh

jimp

I believe I'd already put that into 2.0.3.

heper

Thanks for the heads up about the patch jimp.
For whatever reason it does not seem to work in all scenarios on 2.0.3

I've attached a new screenshot; hopefully it contains some clue's to figure out how to get this working properly.
note that my ovpn instances have all been assigned to interfaces and that quagga binds itself to the interfaces and not the ovpn itself.

Thanks in advance.

PF_quagga_redundant_ovpn.png_thumb

jimp

I have an idea on how to fix this, but since I can't replicate it locally, I need a guinea pig to test the fix. Any takers?

With the most current version of the Quagga OSPF package installed, install the System Patches package and apply this patch:

http://files.pfsense.org/jimp/patches/quagga-tun-route-fix.patch
Path Strip: 1
Base: /
Ignore Whitespace: checked

Then edit/save the Quagga OSPF Settings.

heper

patch fetch failed on webgui. When going to that link with browser i get a 403 - Forbidden ; probably needs a 6 somewhere in the chmod ;)

i'll gladly volunteer as i am the one who keeps bothering you with this :D

jimp

ok try now

heper

i haven't had time to fully look into it, but i'm having some odd preliminary results.

when enabling patch on PF1 it stops finding ANY neighbours. yet no errors in quagga webgui. Reverting the patch makes it work again.
i'll try rebooting PF1 after closing time in the next couple of days to see if that resolves it.

when enabling patch on PF2 everything seems to remain functional.

I've also setup another site, lets call it PF3. I've setup a vpn to PF1 and a seperate one to PF2.
without the patch quagga see's both members, with the patch it only see's 1 member. (not sure if this is intended behaviour or not)

i'll investigate further when i find some spare time …

jimp

What OpenVPN role do each of those have? Client? Server?

What did the OSPF status look like on the ones that did work compared to the ones that didn't? Did it show as being attached to the interface?

Reiner030

Hi,

@heper:

i haven't had time to fully look into it, but i'm having some odd preliminary results.

i'll investigate further when i find some spare time …

we need this patch also … I tested it and found out that ospfd.conf wrote for server and client same line for OpenVPN client and server.

network 172.16.4.1/32 area 192.168.6.0

Normally it must be:

server side:
network 172.16.4.2/32 area 192.168.6.0
client side:
network 172.16.4.1/32 area 192.168.6.0

=> I think /guess there is a logical error in your network mask decision because the OpenVPN mask is /30 and not /32 in Openvpn config (but on ovpn interface later)

        if ($subnet == 32) {

but I'm not sure.

Bests

jimp

The mask selection isn't the issue, there's probably a bit of a logic error in the client or server detection, I just haven't had a chance to go back and hack on it. Probably a very simple fix.

heper

@jimp:

What OpenVPN role do each of those have? Client? Server?

What did the OSPF status look like on the ones that did work compared to the ones that didn't? Did it show as being attached to the interface?

It seems WITH patch that only the ovpn-client neighbour is found. without patch both are found.
for more info see pdf's attached. As noted before i do have on 1 point in my mashup of vpn's where no members are found when patch is enabled, this while there are both client as server instances.

if you require more logs/screenshots/… please let me know

Reiner030

ok, next guess ^^

http://blog.milkfarmsoft.com/2007/11/ip2long-32-bit64-bit/
http://forums.phpfreaks.com/topic/254568-bitwise-not-wip2long-32-bit-vs-64-bit-os/

still "buggy"…

=> + $baselong = ip2long32($ip) & ip2long("255.255.255.252");

must be better
=> + $baselong = ip2long32($ip) & ip2long32("255.255.255.252");

I try to check it later when our network is not used…

Must it be the p2p IP/32 or could we not easy add the OpenVPN "network /30" to quagga ?

jimp

It used /30 before, that's the whole problem.

Let me know if the ip2long32 change works. I still haven't had time to go back and try it.

Reiner030

Hi,

I modified the patch and seems that the missing (typo) 32 in the function name is the problem…
Actually I'm running OpenVPN tunnel with quagga routing searching for my next problem ^^
(Nagios checks won't reach/get response when routing over OpenVPN tunnel)

Reiner030

mmh, actually it won't work again…

Perhaps because I need a "separated" OpenVPN tunnel which is bound to an interface (opt12) ...
We have OpenVPN client networks... and one bridge network and want allow all traffic going between the (transfer) bridge network but not from/to the client networks...

jimp

ok I fixed the line in the patch to have ip2long32. I'm not sure about your other question, that may need its own thread since it may not be related to the problem that initiated this discussion.

Reiner030

Hi yes, could be perhaps another thread/problem…
Only the idea / nice to have that this patch can fix both scenarios if possible ;)

I tested before and got stable OpenVPN tunnel... with quagga routing/traffic.

Then I setup like this to filter traffic separately per tunnel:
http://doc.pfsense.org/index.php/Can_I_filter_OpenVPN_traffic%3F#Assign_OpenVPN_interface_as_OPT

but now get wrong IP in server back and quagga is disables on my server interface again:
network 172.16.4.1/32 area 192.168.6.0

heper

@reiner030 so you have found that it works on a tunnel but stops working when you assign an interface to the tunnel ?

I just confirmed that members are can only be found on ovpn-client side of the tunnel.

situation:

ovpns_A –-----interwebs--------- ovpnc_A
ovpnc_B -------interwebs--------- ovpns_B

if patch is enabled on both ends: no members found by "left" nor "right"
if patch is enabled on the "left" side but not the "right": 1 member is found on the B-connection
if patch is enabled on the "right" side but not the "left": 1 member is found on the A-connection

do note that all vpn's have been assigned an interface and quagga is bound on the interfaces

hope this makes sense somehow ;)

Reiner030

mmh, not sure ..
Yesterday it works for me but perhaps only because my server side was not restarted and my manually fix in the quagga config was still available.
Ssince yesterday evening it won't work again as written so it could be the "old" problem and not my bridge try…

Make sense when taking a look onto interfaces... the OpenVPN tunnel => Interface assigning makes no difference to my interface definition itself:

ovpns5: flags=8051 <up,pointopoint,running,multicast>metric 0 mtu 1500
options=80000 <linkstate>inet6 fe80::225:90ff:fe26:1f22%ovpns5 prefixlen 64 scopeid 0x6e
inet 172.16.4.1 –> 172.16.4.2 netmask 0xffffffff
nd6 options=43 <performnud,accept_rtadv>Opened by PID 3002

so perhaps for 1st fix it's help to apply the patch only to client side ? I try it at evening again…</performnud,accept_rtadv></linkstate></up,pointopoint,running,multicast>

tomas1list.ru

Hello - i think i have same problem (http://forum.pfsense.org/index.php?topic=60942.new;topicseen#new) like in this tread - i try to do failover OPENVPN site-to-site tunnel.
I found some instructions on the forum - for setting up the VPN failover scheme. And no one else had similar problems - so that Openvpn demo fails to start- why not all users have this problem?
I tried to apply patches - it did not help me. Is there a 100% solution to this problem?
I use pfsense 2.0.2
thanks.

heper

@tomas1

no solution at the moment. i hope the developers find some spare time to look into this further.

it has worked in the past.
2.0.1 with openospf worked for sure ; 2.0.1 in a mixed environment with quagga & openospf also worked.
around the time i've updated my site's to 2.0.2 - ALL - with quagga i've started to notice some odd behaviour but didn't have the time to worry about it.