Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    Nic card failure

    Off-Topic & Non-Support Discussion
    2
    13
    4.1k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • T
      tadleymansions
      last edited by

      Steve Hi. Thanks for responding. I think that the first line of your first message indicates the level at which I am at. So not patronising at all - and if you were it would not matter a jot. Have supported user software on MS for many years but this is all new to me since retiring.

      pfSense has performed with so little problems and when they did my "man who knows what he is doing" talked me through fixing the problem (and I don't think that it was ever pfSense - always router or hardware as I recall).

      But back to problem. I am paranoid about upsetting things so have avoided doing anything that I am not sure of.

      Yes have replaced the Nic and no it was not the same type. I did venture into the assign interfaces (option 1) but chickened out after answering no to the vlan question as I did not want to screw up the two connections that seem OK.

      can I just  assign the one interface or do I have to re-do all three?

      The manual says that you plug in a cable as each interface is listed. Am I correct?

      John

      1 Reply Last reply Reply Quote 0
      • stephenw10S
        stephenw10 Netgate Administrator
        last edited by

        Ok, it appears from your quetions that you are using the console on the pfSense box to do this, yes? Are you just using the keyboard/monitor directly or connecting via SSH?

        Since your LAN interface is already setup you should be able to do everything you need to via the web gui.

        In the simplest case you probably need to go to Interfaces: (assign): PPPs: and then edit your PPPoE0 connection. In the drop down select the new NIC you installed, which will presumably be whatever is listed there that isn't fxp0 or rl0.

        That assumes everything else has gone perfectly, which it may not.  ;)

        Now usually when you remove a NIC pfSense will ask you to re-assign the interfaces at the next boot because things have changed. However I'm not sure if that would happen with the base NIC of a PPPoE connection because it's not actually assigned. It seems like this didn't happen because you say your selected option 1 from the menu to assign interfaces rather than being force to do so.

        The output of ifconfig from the command line would help a lot here. If you SSH to the box you can easily copy and paste the output.
        Alternatively you can run it from the webgui in Diagnostics: Command Prompt: in the Execute Shell Command box.

        Steve

        1 Reply Last reply Reply Quote 0
        • T
          tadleymansions
          last edited by

          Hi Steve
          With the confidence you gave me in your posts yesterday things have moved on a bit (a lot maybe??)

          In between me raising the first question and receiving your replies I had begun to think that it was the router (bridge) that was flakey and maybe not the Nic. So, with new found confidence following your response, I replaced the Nic with the original. I then replaced the router (bridge) and rebooted everything hoping that all would magically fall back into place and we would be up and running.

          Not so.

          So, again with the confidence instilled by your good self, I have re-assigned the interfaces and set the interface IP addresses. For the WAN I put in 192.168.1.1 - it was the only thing that seemed to work - and I now have:
          WAN (wan)        re0        192.168.1.11 (DHCP)
          LAN (lan)          rl0        192.168.200.254
          OPT1 (opt1)      fxp0      192.168.10.254

          And all seems to be working except that I cannot now get to the dashboard with my browser.

          I am not sure about the way I have set up the WAN. I set it with DHCP and the system tells me that I can access the webConfigurator with http://dhcp:/ but that doesn't seem to work.

          Where have I gone wrong?

          John
          PS what part of the world are you in? Me UK

          1 Reply Last reply Reply Quote 0
          • stephenw10S
            stephenw10 Netgate Administrator
            last edited by

            Ah OK.
            Hmm, if you set it to dhcp you should not have to enter an IP for WAN because it will receive one automatically via dhcp.

            @tadleymansions:

            I set it with DHCP and the system tells me that I can access the webConfigurator with http://dhcp:/ but that doesn't seem to work.

            This would normally show the name of your pfSense box, if you have set one. The fact that is says 'dhcp' perhaps implies you typed dhcp in the wrong field? Or that something has gone very wrong indeed.  ;)

            I can't really understand why you can't get to the webgui via the browser. Can you ping 192.168.200.254 from a client machine on LAN?

            I'm in London.

            Steve

            1 Reply Last reply Reply Quote 0
            • T
              tadleymansions
              last edited by

              hi Steve. thanks for your continued input.
              Since your last post I have been at it constantly - going round and round in circles I think. I managed to lose all contact with the outside world - hence the slow response.
              I think the answer to one question may well help:-

              On the console screen that gives all the options what should I be seeing against the WAN interface?

              Given that the router is acting as a modem and my internet connection is via a dynamically allocated IP from my ISP, is
              WAN (wan)        re0            NONE (DHCP)

              correct??

              John

              1 Reply Last reply Reply Quote 0
              • stephenw10S
                stephenw10 Netgate Administrator
                last edited by

                No. If your modem is bridged such that the pfSense box is connecting to the ISP via PPPoE you should see:

                 WAN (wan)                 -> pppoe0     -> 90.145.56.35 (PPPoE)

                Obviously not that IP though.

                Steve

                1 Reply Last reply Reply Quote 0
                • T
                  tadleymansions
                  last edited by

                  so what do I have to enter in option 2 - Set Interface IP addresses to achieve this?
                  John

                  1 Reply Last reply Reply Quote 0
                  • stephenw10S
                    stephenw10 Netgate Administrator
                    last edited by

                    I said in another recent thread, it's such a long time since I set up my own home PPPoE connections that I'm struggling to remember the correct order to do this. Basically I suspect that the configuration you had when you first posted was mostly correct but now you have re-assigned the interfaces this are a little more complex.

                    Here's what you do. Setting up the pppoe connection requires the webgui, it can't be done at the console. At least not without resorting to command line incantations!  ;)

                    In the webgui go to Interfaces: (assign):. In the drop down next to WAN check to see if pppoe0 is already an option. It may be since you were previously using it in which case select that and apply the setting.

                    If not then go to Interfaces: WAN: and change the type to PPPoE. Fill in the connection details from your ISP. Save and apply.

                    Steve

                    1 Reply Last reply Reply Quote 0
                    • T
                      tadleymansions
                      last edited by

                      Hi Steve
                      Many many thanks for your help in trying to resolve my problem. Nothing I tried (or dared to try) seemed to get me to the correct configuration and I retired hurt on Sunday evening.
                      Thankfully my man returned on Monday and talked me through a complete re-configuration from modem tru to a defgalt re-start of pfsense (something I dared not to do) and all is now well.

                      I certainly have learned an awful lot over the last few days and am resolved to learn more about pfsense.

                      Once again thanks for your help.

                      John

                      1 Reply Last reply Reply Quote 0
                      • stephenw10S
                        stephenw10 Netgate Administrator
                        last edited by

                        @tadleymansions:

                        I certainly have learned an awful lot over the last few days and am resolved to learn more about pfsense.

                        Not all bad then.  ;) Thanks for signing off.

                        Steve

                        1 Reply Last reply Reply Quote 0
                        • First post
                          Last post