LCDProc 0.5.4-dev

joako

Has anyone managed to get lcdexec running or even have a sample config file?

I have to problems to configure it in Linux but on pfsense with the -dev package all I can manage to get is the fatal error: "no main menu found in configuration"

I do have [MainMenu] section in the config

menacingm

Thank you for the code release fmertz. I can confirm that this is working on the XTM 5 series and corrects the improper keymapping.

However,
output 1 caused a green slow blink
output 2 caused a red slow blink
output 3 caused a green slow blink
…
output 6 caused a red/green blink
...
output 9 caused a red/green blink

I can test further if you'd like but I just wanted to share my experience. StephenW could probably assist with getting this right.

@fmertz:


telnet localhost 13666
hello
connect LCDproc 0.5.5 protocol 0.3 lcd wid 20 hgt 2 cellwid 5 cellhgt 8
output 1 <—Should start blinking red, rare short blink
success
output 2 <—Should start blinking green, rare short blink
success

stephenw10

Nine months after the code release and you're still beaten me to it! ::)

Did you have any problems with starting the service? If you read back through this thread you'll see many, many posts with people trying to find the correct command line to start both lcdd and the php client at boot. It seems very much time dependent such that some boxes start OK while the X-e box ends up with two lcdds running and no client. I spent many hours trying to resolve that and never did which is why I never got around to testing fmertz's code.

I haven't tried it under 2.0.3 and I know there was some talk of altering the package start sequence.

I'm sure we can fix the led control since it looks to be working to some extent.

Steve

stephenw10

Reading through the code for the LED sequencing:

API: Updates LEDs as per "state". Here, "state" is supposed to contain the sequence the LEDs are

to be lit by. We need to support Red, Green and Off. Therefore, we need 2 bits to encode the

possible values. So, a 32 bit "state" can host a sequence of 16 separate illuminations. Each

group of 2 bits is examined in sequence, as a time slot, each time output is called, and the

hardware LEDs are updated accordingly.

Thus, output 6 translates to:

32 bit Binary 0000 0000 0000 0000 0000 0000 0000 0110

2-bit seq 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 2

It does seem as if red and green are swapped but otherwise the sequence is as expected.
More interestingly try something like:

2-bit seq 0 2 0 2 0 2 0 2 0 2 0 2 1 1 1 1

32 bit Binary 0010 0010 0010 0010 0010 0010 0101 0101 00100010001000100010001001010101

Decimal 572662357

Steve

stephenw10

Ok, it's simply the values are the wrong way around in the code:

case LPC_DEVICE_82801GBGR: 	/* XTM: W83627THG SuperIO */
	shift = 0x48;		/* offset for GPIO BASE */
	level = SIO_EFIR;	/* SuperIO chip is hard wired */
	level2 = SIO_EFDR;	/* to LPC ports 2E and 2F */
	p->red_bit = 0x10;
	p->grn_bit = 0x20;
	break;

My original findings:
@stephenw10:

Then the led can be controlled via CRF1:

Control Register F1     Bit5 Bit4	Arm/Disarm LED
0x00			0 0		Off
0x10			0 1		Green
0x20			1 0		Red
0x30			1 1		Off

Easy fix! :)

Steve

menacingm

My process for updating the driver was pretty simple. Sopped the LCDproc service from the Web Configurator, SSHd into my box and navigated to /usr/local/lib/lcdproc. Renamed sdeclcd.so to sdeclcd2.so and wget the new build. Checked permissions on sdeclcd.so and it needed a chmod +x. Then I was able to start up LCDProc from the webconfigurator with no problems. Haven't rebooted yet so I'll give that a go now and let you all know how it goes.

menacingm

I can confirm that although it was set to start at boot, the service didn't start after a reboot. It did however start right up manually from the webconfigurator. Here are the logs:

Apr 27 20:31:56	LCDd: LCDd version 0.5.5 starting
Apr 27 20:31:56	LCDd: Using Configuration File: /usr/local/etc/LCDd.conf
Apr 27 20:31:56	LCDd: Listening for queries on 127.0.0.1:13666
Apr 27 20:31:56	php: lcdproc: Start client procedure. Error counter: (0)
Apr 27 20:31:57	LCDd: Connect from host 127.0.0.1:9995 on socket 11
Apr 27 20:31:58	apinger: rrdtool respawning too fast, waiting 300s.
Apr 27 20:33:44	php: lcdproc: Sync: Begin package sync
Apr 27 20:33:44	check_reload_status: Syncing firewall
Apr 27 20:33:44	php: lcdproc: Sync: Restarting the service
Apr 27 20:33:45	LCDd: Client on socket 11 disconnected
Apr 27 20:33:45	LCDd: sock_send: socket write error
Apr 27 20:33:45	LCDd: sock_send: socket write error
Apr 27 20:33:45	LCDd: sock_send: socket write error
Apr 27 20:33:45	LCDd: sock_send: socket write error
Apr 27 20:33:45	LCDd: sock_send: socket write error
Apr 27 20:33:45	LCDd: sock_send: socket write error
Apr 27 20:33:45	LCDd: sock_send: socket write error
Apr 27 20:33:45	LCDd: sock_send: socket write error
Apr 27 20:33:45	LCDd: sock_send: socket write error
Apr 27 20:33:45	LCDd: sock_send: socket write error
Apr 27 20:33:45	LCDd: sock_send: socket write error
Apr 27 20:33:45	LCDd: sock_send: socket write error
Apr 27 20:33:45	LCDd: sock_send: socket write error
Apr 27 20:33:45	LCDd: sock_send: socket write error
Apr 27 20:33:45	LCDd: sock_send: socket write error
Apr 27 20:33:45	LCDd: Server shutting down on SIGTERM
Apr 27 20:33:46	LCDd: sdeclcd: cannot release IO-permission for 0x02E!
Apr 27 20:33:46	LCDd: sdeclcd: cannot release IO-permission for 0x02F!
Apr 27 20:33:46	LCDd: sdeclcd: cannot release IO-permission for 0x378!
Apr 27 20:33:49	php: lcdproc: Sync: End package sync
Apr 27 20:33:49	LCDd: LCDd version 0.5.5 starting
Apr 27 20:33:49	LCDd: Using Configuration File: /usr/local/etc/LCDd.conf
Apr 27 20:33:49	LCDd: Listening for queries on 127.0.0.1:13666
Apr 27 20:33:50	php: lcdproc: Start client procedure. Error counter: (0)
Apr 27 20:33:51	LCDd: Connect from host 127.0.0.1:3180 on socket 11

stephenw10

Ah, disappointing but not unexpected. :(

If you run 'ps aux|grep lcd' or 'ps aux|grep LCD' (there is a switch to make it ignore case but I can't remember it!) you may find it has started several instances of lcdd or is hung up waiting for a php instance to close.
Edit: It's 'ps aux|grep -i lcd'

Brak had some code the he said worked OK but I never got around to testing it. It's really ridiculous, IMHO, that the packages are restarted so many times at boot especially as something like this never needs to be restarted.

Steve

menacingm

Brak's lcdproc.inc only made things worse. Didn't fix the startup issues and on reboot a few other services didn't startup.

stephenw10

Damn. :(
There is some underlying problem here. It seems to be only an issue with the sdeclcd driver which means most people don't have a problem.
There is nothing obvious in the driver that might be introducing a delay. I have to say that reading through François' code is a joy. Compared to my own feeble efforts his is so professional. ::)

Did you try a longer LED sequence?

Steve

fmertz

@stephenw10:

Ok, it's simply the values are the wrong way around in the code:

case LPC_DEVICE_82801GBGR: 	/* XTM: W83627THG SuperIO */
	shift = 0x48;		/* offset for GPIO BASE */
	level = SIO_EFIR;	/* SuperIO chip is hard wired */
	level2 = SIO_EFDR;	/* to LPC ports 2E and 2F */
	p->red_bit = 0x10;
	p->grn_bit = 0x20;
	break;

My original findings:
@stephenw10:

Then the led can be controlled via CRF1:

Control Register F1     Bit5 Bit4	Arm/Disarm LED
0x00			0 0		Off
0x10			0 1		Green
0x20			1 0		Red
0x30			1 1		Off

Easy fix! :)

Steve

Thanks for the heads up. I'll update the code accordingly. Not a bad first run, really, considering this was coded "off the spec"…

fmertz

@stephenw10:

There is nothing obvious in the driver that might be introducing a delay. I have to say that reading through François' code is a joy. Compared to my own feeble efforts his is so professional. ::)

Thanks for the kind words about the code. The idea was to make it clean enough to make it acceptable for the upstream project, and make it available to all, whether I am the maintainer or not. It seemed like a shame to have all that gold information posted on this forum in terms of discoveries, and the countless hours of research that to go with them, without someone collecting it and regurgitating it in proper code form so it never goes extinct. Glad to hear someone is actually reading through it, though. ;)

Altogether, the LCD spec called for a very specific initialization sequence that takes more time. FWIW, the old code did not seem to properly reset the LCD when things went wrong, and a full reboot was necessary to clear things up. When this new sequence was implemented in the new code, just restarting the LCDproc package was enough to reset the LCD. The new delay is coded as:


	sdec_exec_wait(SDEC_FN_FUNCTION_SET | SDEC_OPT_8_BIT, 15000);

15000 micro seconds, 15ms.

Altogether, drivers control hardware, and should be allowed to have whatever timing quirks are required by the device they control. This includes slow initialization sequences, etc. Maybe the controller code needs to be looked at again. The errors from the driver code complaining of not being able to release the I/O ports might indicate there are multiple copies of this driver in memory…

menacingm

Stephen & Francois, glad to have you 2 brilliant minds working on this.

I haven't tried the new driver with the new delay and value order yet, running some development projects behind the pfsense box and need it up and stable for a few more weeks.

Stephen, did you get a chance to test to see if this corrects the SDECLCD driver boot initialization errors?

Francois, has the new SDECLCD driver reached a point where it can be committed to the next point release of lcdproc-dev?

Thanks guys

stephenw10

It's been accepted upstream so I don't see why not.
I still haven't been able to get it to start cleanly and reliably. To work around this I proposed running the new driver but starting it using the shellcmd package. This avoids more than one start. I've been running several boxes like that for a few weeks with no issues. See: http://forum.pfsense.org/index.php/topic,7920.msg344513.html#msg344513

Steve

jimp

The SDECLCD driver is in the current lcdproc-dev package after I bumped it this week by request. I don't have one any LCDs to try it with, but the correct binary appears to be there now (on 32 and 64 bit) included in the main lcdproc binaries, not pulled in separately anymore.

menacingm

I can confirm the latest LCDProc-Dev/Watchguard SDECLCD driver release available through the official PFSense package install still suffers from the same issues. Key mapping is not correct on the Watchguard XTM5 series and the service fails to start on boot.

I'm not sure if the binary jimp is referring to has been pushed to the official package yet, but I will tinker and report back.

Stephen,

I'm having some trouble getting the right shellcmd to start/restart the LCDProc service. Would you mind sharing that ShellCmd?

Thanks,

stephenw10

It's detailed in the post I linked to above.

Two interesting developments have happened recently that may help here.
JimP's watchdog package. It may be able to restart the service correctly after boot and if it fails. Though I suspect it only monitors the daemon and not the client.
The rc startup patches may help lcdproc-dev start correctly at boot.

Steve

Topper727

I have the CrystalFontz 735 Display which emulates the 635 and will go Graphic here in the very near future.

I am wondering why the LED's on the display don't light using LcdProc. What can I do?

stephenw10

You mean the backlight or some other LEDs?

Steve

kilthro

@stephenw10:

You mean the backlight or some other LEDs?

Steve

The leds down the side of the front of the unit.

@Topper727:

I have the CrystalFontz 735 Display which emulates the 635 and will go Graphic here in the very near future.

I am wondering why the LED's on the display don't light using LcdProc. What can I do?

You can get them to work.
I am still using this process/edits to the files and mine work. Not sure if much is diff between the 635/735 besides different type of lcd..

You may be able to apply this to get them to work.

http://forum.pfsense.org/index.php/topic,44034.msg302352.html#msg302352