Cheap, small, and quiet hardware?
-
Also, I have a EPIA-EK1000G lying around, with a gig of DDR installed. I've never tried to power it on. Might be a potential choice.
It doesn't get cheaper than something you already have. Looks like a good candidate, dual NIC and has VIA padlock which will boost OpenVPN considerably. It should handle a 100/20 WAN connection without a problem if you aren't running packages.
You would need aditionally:
A case. You could do without a case but that's probably unwise!
Storage. Any old HD will do or use a CF card in an IDE adapter.
A PSU. You can use any power supply since this board draws only 19W but you will get much better efficiency using a DC-DC PSU such as the picoPSU.Steve
-
Also, I have a EPIA-EK1000G lying around, with a gig of DDR installed. I've never tried to power it on. Might be a potential choice.
It doesn't get cheaper than something you already have. Looks like a good candidate, dual NIC and has VIA padlock which will boost OpenVPN considerably. It should handle a 100/20 WAN connection without a problem if yopu aren't running packages.
Fully agree.
-
Also, I have a EPIA-EK1000G lying around, with a gig of DDR installed. I've never tried to power it on. Might be a potential choice.
It doesn't get cheaper than something you already have. Looks like a good candidate, dual NIC and has VIA padlock which will boost OpenVPN considerably. It should handle a 100/20 WAN connection without a problem if you aren't running packages.
You would need aditionally:
A case. You could do without a case but that's probably unwise!
Storage. Any old HD will do or use a CF card in an IDE adapter.
A PSU. You can use any power supply since this board draws only 19W but you will get much better efficiency using a DC-DC PSU such as the picoPSU.Steve
Yeah, I got it powered up and running last night with a 125W ATX psu that I had lying around and the nanobsd build of pfsense on a 4gb flash drive. It already has a case and some sort of DC-DC PSU, although it's much beefier than a picoPSU - about 1/2 the size of the board. I picked up a 60W DC power adapter on eBay which should fit the barrel plug. Now I just need to come up with a permanent storage solution. Will nanoBSD eat my flash drive?
Thanks for all your suggestions, guys. I was a bit nervous posting such a common question as "where do I get cheap hardware?" but nobody flamed me. :)
-
Will nanoBSD eat my flash drive?
Nope, NanoBSD is especially designed to run from flash drives. It runs almost entirely from RAM and mounts the filesystem as readonly most of the time.
http://www.freebsd.org/doc/en/articles/nanobsd/article.html#introSteve
-
Quick question on nanoBSD before this thread dies. Can I install all the heavy packages with no logging.. like Snort, Squid (null cache config), Dans..etc and still be able to run everything ?
-
Quick question on nanoBSD before this thread dies. Can I install all the heavy packages with no logging.. like Snort, Squid (null cache config), Dans..etc and still be able to run everything ?
Yes, as long as the system has enough real memory.
e.g. Alix 2D13 with only 256MB is not enough - when interfaces go up/down, events happen that cause check_reload_status to do a bunch of stuff and the system needs enough spare memory to run a few extra processes, so you can't keep installing packages to fill up 90% of the real memory.
I suspect that 512MB might also prove to be insufficient for the above packages, which rules out the 512MB memory Soekris low-power boxes. Please comment if you have experience of that.
I am hoping that the new Alix board for 2013 will be an option soon - http://forum.pfsense.org/index.php/topic,59555.0.html -
The only packages that can't be installed are marked 'noembedded true' in package list:
http://www.pfsense.org/packages/pkg_config.8.xml.Thus packages that can't be installed on Nano are:
pure-ftpd
ntop
FreeSWITCH
Lightsquid
phpSysInfoOf course there is a difference between 'will install' and 'runs well'. ;)
Steve
-
Hmm.. so could I install a nano image using a USB drive on to a 8GB CF like the memstick version that can be loaded to a typical hdd? the CF would be the real drive for it but would just need USB to boot and install it to CF. Can this be done?
-
Not quite sure what you mean.
Usually you just write the nanobsd image directly to the CF card using some external device like a usb card reader.Steve
-
Ahh is it. So I just put the image on the CF card and it will boot?
-
Yep, an image with 2 bootable partitions (plus a partition for the config) is written. So you can even go back and forth if an upgrade is troublesome.
Instructions here: http://doc.pfsense.org/index.php/HOWTO_Install_pfSense