Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    Run pfSense on a watchguard firebox x700

    Scheduled Pinned Locked Moved Hardware
    63 Posts 7 Posters 21.8k Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • N
      ninjamick
      last edited by

      i didnt  get the option to enable anything  i was asked if i wantted vlan  i said no  then it  asked for wan cable  then lan cable  then setup  was complete thats  all i got    i will go  through the waty i connected it  from router to rc0 fbx700 external  then  crossover  from server  to  lan rc1 straight cable then main pc  to firebox rc2  and the console cable to  console of  fbx700  thats the connection  of it  im trying to  get the  details    when i  do  ipconfig i noticed the  ip address is  168 thats  not right  gonna  try  reinstalling  with  diffrent  settings

      1 Reply Last reply Reply Quote 0
      • stephenw10S
        stephenw10 Netgate Administrator
        last edited by

        Which of those is the LAN interface? If it's the one connected to the server then only the server will able to reach the webgui until you add more firewall rules.

        If everything is default the machine connected to the LAN interface should receive an IP address in the 192.168.1.X range. Is that what you meant?

        Steve

        1 Reply Last reply Reply Quote 0
        • N
          ninjamick
          last edited by

          the lan cable is the crossover  cable  which is on the trusted  rc1 when i typed ip config  it read a ip adress  as 168.254.1.1  which is diffrent

          1 Reply Last reply Reply Quote 0
          • stephenw10S
            stephenw10 Netgate Administrator
            last edited by

            OK so if the LAN interface is re1 (I think you must have typo'd that, it should be 're') only the server machine will be able to reach the webgui. Except that, as you say, the IP address is odd.

            You haven't said yet what the interface listing above the console menu says. It will list the current IP address of the LAN interface, is it 192.168.1.1? If not what is it? Could you give us the complete listing please?

            Steve

            1 Reply Last reply Reply Quote 0
            • N
              ninjamick
              last edited by

              i will try  to send you  what i  get 
              rlphy5: <realtek internal="" media="" interface="">PHY 0 on miibus5
              rlphy5:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
              re5: [FILTER]
              isab0: <pci-isa bridge="">at device 31.0 on pci0
              isa0: <isa bus="">on isab0
              atapci0: <intel ich2="" udma100="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x37
              6,0xff00-0xff0f at device 31.1 on pci0
              ata0: <ata 0="" channel="">on atapci0
              ata0: [ITHREAD]
              ata1: <ata 1="" channel="">on atapci0
              ata1: [ITHREAD]
              cpu0 on motherboard
              unknown: <pnp0c01>can't assign resources (memory)
              atrtc0: <at realtime="" clock="">at port 0x70-0x71 irq 8 pnpid PNP0b00 on isa0
              uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 pnpid PNP0501
              on isa0
              uart0: [FILTER]
              uart0: console (9600,n,8,1)
              ppc0: <ecp parallel="" printer="" port="">at port 0x378-0x37f,0x778-0x77a irq 7 drq 3 pn
              pid PNP0401 on isa0
              ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
              ppc0: FIFO with 16/16/16 bytes threshold
              ppc0: [ITHREAD]
              ppbus0: <parallel port="" bus="">on ppc0
              ppi0: <parallel i="" o="">on ppbus0
              orm0: <isa option="" rom="">at iomem 0xe0000-0xe0fff pnpid ORM0000 on isa0
              unknown: <pnp0c01>can't assign resources (memory)
              RTC BIOS diagnostic error 20 <config_unit>Timecounter "TSC" frequency 1202731373 Hz quality 800
              Timecounters tick every 10.000 msec
              IPsec: Initialized Security Association Processing.
              ad0: 3871MB <cf 20070131="" 4gb="">at ata0-master PIO4
              Trying to mount root from ufs:/dev/ufs/pfsense0
              Configuring crash dumps…
              Mounting filesystems...
              Setting up embedded specific environment... done.

              ___
              / f
              / p _              / Sense
              _              / 
                  _              _/

              Welcome to pfSense 2.0.3-RELEASE  ...

              Creating symlinks......done.
              External config loader 1.0 is now starting... ad0s3
              Launching the init system... done.
              Initializing............................ done.
              Starting device manager (devd)...done.
              Loading configuration......done.
              Updating configuration...done.
              Cleaning backup cache.....done.
              Setting up extended sysctls...done.
              Setting timezone...done.
              Starting Secure Shell Services...done.
              Setting up polling defaure0: link state changed to DOWN
              lts...done.
              Setting up interfaces microcode...done.
              Configuring LAGG interfaces...done.
              Configuring VLAN interfaces...done.
              Configuring QinQ interfaces...done.
              Configuring WAN interface...re0: link state changed to UP
              done.
              Syncing OpenVPN settings...done.
              Starting syslog...done.
              Configuring firewall......done.
              Starting PFLOG...done.
              Setting up gateway monitors...done.
              Synchronizing user settings...done.
              Starting webConfigurator...done.
              Configuring CRON...done.
              Starting NTP time client...Starting DNS forwarder...done.
              Configuring firewall......done.
              Generating RRD graphs...done.
              Starting CRON... done.
              Bootup complete

              1  pfSense
              2  pfSense

              F6 PXE
              Boot:  1
              /boot.config: -h
              Consoles: serial port
              BIOS drive C: is disk0
              BIOS 639kB/261120kB available memory

              FreeBSD/i386 bootstrap loader, Revision 1.1
              (root@snapshots-8_1-i386.builders.pfsense.org, Fri Apr 12 11:01:35 EDT 2013)
              Loading /boot/defaults/loader.conf
              /boot/kernel/kernel text=0x8b1f9c data=0x3caa54+0x9b720 syms=[0x4+0x952a0+0x4+0x
              cca1b]
              |
              Hit [Enter] to boot immediately, or any other key for command prompt.
              Booting [/boot/kernel/kernel]…
              Copyright (c) 1992-2010 The FreeBSD Project.
              Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
                      The Regents of the University of California. All rights reserved.
              FreeBSD is a registered trademark of The FreeBSD Foundation.
              FreeBSD 8.1-RELEASE-p13 #0: Fri Apr 12 11:10:09 EDT 2013
                  root@snapshots-8_1-i386.builders.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc
              /src/sys/pfSense_wrap.8.i386 i386
              Timecounter "i8254" frequency 1193182 Hz quality 0
              CPU: Intel(R) Celeron(TM) CPU                1200MHz (1202.73-MHz 686-class CPU)

              Origin = "GenuineIntel"  Id = 0x6b4  Family = 6  Model = b  Stepping = 4
                Features=0x383f9ff<fpu,vme,de,pse,tsc,msr,pae,mce,cx8,sep,mtrr,pge,mca,cmov,pa<br>T,PSE36,MMX,FXSR,SSE>
              real memory  = 268435456 (256 MB)
              avail memory = 243429376 (232 MB)
              ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
              ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /bo
              ot/loader.conf.
              module_register_init: MOD_LOAD (ipw_bss_fw, 0xc0712580, 0) error 1
              wlan: mac acl policy registered
              ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
              ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /b
              oot/loader.conf.
              module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc0712620, 0) error 1
              ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw
              /.
              ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in
              /boot/loader.conf.
              module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc07126c0, 0) error 1
              wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
              wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/l
              oader.conf.
              module_register_init: MOD_LOAD (wpi_fw, 0xc0891ba0, 0) error 1
              ACPI Error: A valid RSDP was not found (20100331/tbxfroot-309)
              ACPI: Table initialisation failed: AE_NOT_FOUND
              ACPI: Try disabling either ACPI or apic support.
              cryptosoft0: <software crypto="">on motherboard
              padlock0: No ACE support.
              pcib0: <intel 82815="" (i815="" gmch)="" host="" to="" hub="" bridge="">pcibus 0 on motherboard
              pir0: <pci 11="" interrupt="" routing="" table:="" entries="">on motherboard
              $PIR: Using invalid BIOS IRQ 9 from 2.13.INTA for link 0x63
              pci0: <pci bus="">on pcib0
              pcib1: <pci-pci bridge="">at device 1.0 on pci0
              pci1: <pci bus="">on pcib1
              pcib2: <pcibios pci-pci="" bridge="">at device 30.0 on pci0
              pci2: <pci bus="">on pcib2
              safe0 mem 0xe7bfe000-0xe7bfffff irq 3 at device 6.0 on pci2
              safe0: [ITHREAD]
              safe0: SafeNet SafeXcel-1141 rng des/3des aes md5 sha1 null
              re0: <realtek 10="" 8139c+="" 100basetx="">port 0xd500-0xd5ff mem 0xefefa000-0xefefa1ff
              irq 10 at device 9.0 on pci2
              re0: Chip rev. 0x74800000
              re0: MAC rev. 0x00000000
              miibus0: <mii bus="">on re0
              rlphy0: <realtek internal="" media="" interface="">PHY 0 on miibus0
              rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
              re0: [FILTER]
              re1: <realtek 10="" 8139c+="" 100basetx="">port 0xd600-0xd6ff mem 0xefefb000-0xefefb1ff
              irq 5 at device 10.0 on pci2
              re1: Chip rev. 0x74800000
              re1: MAC rev. 0x00000000
              miibus1: <mii bus="">on re1
              rlphy1: <realtek internal="" media="" interface="">PHY 0 on miibus1
              rlphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
              re1: [FILTER]
              re2: <realtek 10="" 8139c+="" 100basetx="">port 0xd900-0xd9ff mem 0xefefc000-0xefefc1ff
              irq 11 at device 11.0 on pci2
              re2: Chip rev. 0x74800000
              re2: MAC rev. 0x00000000
              miibus2: <mii bus="">on re2
              rlphy2: <realtek internal="" media="" interface="">PHY 0 on miibus2
              rlphy2:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
              re2: [FILTER]
              re3: <realtek 10="" 8139c+="" 100basetx="">port 0xda00-0xdaff mem 0xefefd000-0xefefd1ff
              irq 12 at device 12.0 on pci2
              re3: Chip rev. 0x74800000
              re3: MAC rev. 0x00000000
              miibus3: <mii bus="">on re3
              rlphy3: <realtek internal="" media="" interface="">PHY 0 on miibus3
              rlphy3:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
              re3: [FILTER]
              re4: <realtek 10="" 8139c+="" 100basetx="">port 0xdd00-0xddff mem 0xefefe000-0xefefe1ff
              irq 9 at device 13.0 on pci2
              re4: Chip rev. 0x74800000
              re4: MAC rev. 0x00000000
              miibus4: <mii bus="">on re4
              rlphy4: <realtek internal="" media="" interface="">PHY 0 on miibus4
              rlphy4:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
              re4: [FILTER]
              re5: <realtek 10="" 8139c+="" 100basetx="">port 0xde00-0xdeff mem 0xefeff000-0xefeff1ff
              irq 6 at device 14.0 on pci2
              re5: Chip rev. 0x74800000
              re5: MAC rev. 0x00000000
              miibus5: <mii bus="">on re5
              rlphy5: <realtek internal="" media="" interface="">PHY 0 on miibus5
              rlphy5:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
              re5: [FILTER]
              isab0: <pci-isa bridge="">at device 31.0 on pci0
              isa0: <isa bus="">on isab0
              atapci0: <intel ich2="" udma100="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x37
              6,0xff00-0xff0f at device 31.1 on pci0
              ata0: <ata 0="" channel="">on atapci0
              ata0: [ITHREAD]
              ata1: <ata 1="" channel="">on atapci0
              ata1: [ITHREAD]
              cpu0 on motherboard
              unknown: <pnp0c01>can't assign resources (memory)
              atrtc0: <at realtime="" clock="">at port 0x70-0x71 irq 8 pnpid PNP0b00 on isa0
              uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 pnpid PNP0501
              on isa0
              uart0: [FILTER]
              uart0: console (9600,n,8,1)
              ppc0: <ecp parallel="" printer="" port="">at port 0x378-0x37f,0x778-0x77a irq 7 drq 3 pn
              pid PNP0401 on isa0
              ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
              ppc0: FIFO with 16/16/16 bytes threshold
              ppc0: [ITHREAD]
              ppbus0: <parallel port="" bus="">on ppc0
              ppi0: <parallel i="" o="">on ppbus0
              orm0: <isa option="" rom="">at iomem 0xe0000-0xe0fff pnpid ORM0000 on isa0
              unknown: <pnp0c01>can't assign resources (memory)
              RTC BIOS diagnostic error 20 <config_unit>Timecounter "TSC" frequency 1202731384 Hz quality 800
              Timecounters tick every 10.000 msec
              IPsec: Initialized Security Association Processing.
              ad0: 3871MB <cf 20070131="" 4gb="">at ata0-master PIO4
              Trying to mount root from ufs:/dev/ufs/pfsense0
              Configuring crash dumps…
              Mounting filesystems...
              Setting up embedded specific environment... done.

              ___
              / f
              / p _              / Sense
              _              / 
                  _              _/

              Welcome to pfSense 2.0.3-RELEASE  ...

              Creating symlinks......done.
              External config loader 1.0 is now starting... ad0s3
              Launching the init system... done.
              Initializing............................ done.
              Starting device manager (devd)...done.
              Loading configuration......done.

              Network interface mismatch -- Running interface assignment option.
              re0: link state changed to DOWN
              re1: link state changed to DOWN
              re2: link state changed to DOWN
              re3: link state changed to DOWN
              re4: link state changed to DOWN
              re5: link state changed to DOWN

              Valid interfaces are:

              re0  00:90:7f:2f:c3:d1  (up) RealTek 8139C+ 10/100BaseTX
              re1  00:90:7f:2f:c3:d2  (up) RealTek 8139C+ 10/100BaseTX
              re2  00:90:7f:2f:c3:d3  (up) RealTek 8139C+ 10/100BaseTX
              re3  00:90:7f:2f:c3:d4  (up) RealTek 8139C+ 10/100BaseTX
              re4  00:90:7f:2f:c3:d5  (up) RealTek 8139C+ 10/100BaseTX
              re5  00:90:7f:2f:c3:d6  (up) RealTek 8139C+ 10/100BaseTX

              Do you want to set up VLANs first?

              If you are not going to use VLANs, or only for optional interfaces, you should
              say no here and use the webConfigurator to configure VLANs later, if required.

              Do you want to set up VLANs now [y|n]? n

              NOTE  pfSense requires AT LEAST 1 assigned interface(s) to function.
                      If you do not have AT LEAST 1 interfaces you CANNOT continue.

              If you do not have at least 1 REAL network interface card(s)
                      or one interface with multiple VLANs then pfSense
                      WILL NOT function correctly.

              If you do not know the names of your interfaces, you may choose to use
              auto-detection. In that case, disconnect all interfaces now before
              hitting 'a' to initiate auto detection.

              Enter the WAN interface name or 'a' for auto-detection: rc1

              Invalid interface name 'rc1'

              Enter the WAN interface name or 'a' for auto-detection: a

              Connect the WAN interface now and make sure that the link is up.
              Then press ENTER to continue.
              re0: link state changed to UP
              re0: link state changed to DOWN
              re0: link state changed to UP

              Detected link-up on interface re0.

              Enter the LAN interface name or 'a' for auto-detection
              NOTE: this enables full Firewalling/NAT mode.
              (or nothing if finished): re1: link state changed to UP
              re2: link state changed to UP

              The interfaces will be assigned as follows:

              WAN  -> re0

              Do you want to proceed [y|n]?y

              Writing configuration…done.
              Updating configuration...done.
              Cleaning backup cache...done.
              Setting up extended sysctls...done.
              Setting timezone...done.
              Starting Secure Shell Services...done.
              Setting up polling defaults...done.
              Setting up interfaces microcode...done.
              Configuring LAGG interfaces...done.
              Configuring VLAN interfaces...done.
              Configuring QinQ interfaces...done.
              Configuring WAN interface...done.
              Syncing OpenVPN settings...done.
              Starting syslog...done.
              pflog0: promiscuous mode enabled
              Configuring firewall......done.
              Starting PFLOG...done.
              Setting up gateway monitors...done.
              Synchronizing user settings...done.
              Starting webConfigurator...done.
              Configuring CRON...done.
              Starting NTP time client...Starting DNS forwarder...done.
              Configuring firewall......done.
              Generating RRD graphs...done.
              Starting CRON... done.
              Bootup complete

              1  pfSense
              2  pfSense

              F6 PXE
              Boot:  1
              /boot.config: -h

              FreeBSD/i386 boot
              Default: 0:ad(0,a)/boot/loader
              boot: Consoles: serial port
              BIOS drive C: is disk0
              BIOS 639kB/261120kB available memory

              FreeBSD/i386 bootstrap loader, Revision 1.1
              (root@snapshots-8_1-i386.builders.pfsense.org, Fri Apr 12 11:01:35 EDT 2013)
              Loading /boot/defaults/loader.conf
              /boot/kernel/kernel text=0x8b1f9c data=0x3caa54+0x9b720 syms=[0x4+0x952a0+0x4+0x
              cca1b]
              |
              Hit [Enter] to boot immediately, or any other key for command prompt.
              Booting [/boot/kernel/kernel]…
              Copyright (c) 1992-2010 The FreeBSD Project.
              Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
                      The Regents of the University of California. All rights reserved.
              FreeBSD is a registered trademark of The FreeBSD Foundation.
              FreeBSD 8.1-RELEASE-p13 #0: Fri Apr 12 11:10:09 EDT 2013
                  root@snapshots-8_1-i386.builders.pfsense.org:/usr/obj.pfSense/usr/pfSensesrc
              /src/sys/pfSense_wrap.8.i386 i386
              Timecounter "i8254" frequency 1193182 Hz quality 0
              CPU: Intel(R) Celeron(TM) CPU                1200MHz (1202.73-MHz 686-class CPU)

              Origin = "GenuineIntel"  Id = 0x6b4  Family = 6  Model = b  Stepping = 4
                Features=0x383f9ff<fpu,vme,de,pse,tsc,msr,pae,mce,cx8,sep,mtrr,pge,mca,cmov,pa<br>T,PSE36,MMX,FXSR,SSE>
              real memory  = 268435456 (256 MB)
              avail memory = 243429376 (232 MB)
              ipw_bss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
              ipw_bss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /bo
              ot/loader.conf.
              module_register_init: MOD_LOAD (ipw_bss_fw, 0xc0712580, 0) error 1
              wlan: mac acl policy registered
              ipw_ibss: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw/.
              ipw_ibss: If you agree with the license, set legal.intel_ipw.license_ack=1 in /b
              oot/loader.conf.
              module_register_init: MOD_LOAD (ipw_ibss_fw, 0xc0712620, 0) error 1
              ipw_monitor: You need to read the LICENSE file in /usr/share/doc/legal/intel_ipw
              /.
              ipw_monitor: If you agree with the license, set legal.intel_ipw.license_ack=1 in
              /boot/loader.conf.
              module_register_init: MOD_LOAD (ipw_monitor_fw, 0xc07126c0, 0) error 1
              wpi: You need to read the LICENSE file in /usr/share/doc/legal/intel_wpi/.
              wpi: If you agree with the license, set legal.intel_wpi.license_ack=1 in /boot/l
              oader.conf.
              module_register_init: MOD_LOAD (wpi_fw, 0xc0891ba0, 0) error 1
              ACPI Error: A valid RSDP was not found (20100331/tbxfroot-309)
              ACPI: Table initialisation failed: AE_NOT_FOUND
              ACPI: Try disabling either ACPI or apic support.
              cryptosoft0: <software crypto="">on motherboard
              padlock0: No ACE support.
              pcib0: <intel 82815="" (i815="" gmch)="" host="" to="" hub="" bridge="">pcibus 0 on motherboard
              pir0: <pci 11="" interrupt="" routing="" table:="" entries="">on motherboard
              $PIR: Using invalid BIOS IRQ 9 from 2.13.INTA for link 0x63
              pci0: <pci bus="">on pcib0
              pcib1: <pci-pci bridge="">at device 1.0 on pci0
              pci1: <pci bus="">on pcib1
              pcib2: <pcibios pci-pci="" bridge="">at device 30.0 on pci0
              pci2: <pci bus="">on pcib2
              safe0 mem 0xe7bfe000-0xe7bfffff irq 3 at device 6.0 on pci2
              safe0: [ITHREAD]
              safe0: SafeNet SafeXcel-1141 rng des/3des aes md5 sha1 null
              re0: <realtek 10="" 8139c+="" 100basetx="">port 0xd500-0xd5ff mem 0xefefa000-0xefefa1ff
              irq 10 at device 9.0 on pci2
              re0: Chip rev. 0x74800000
              re0: MAC rev. 0x00000000
              miibus0: <mii bus="">on re0
              rlphy0: <realtek internal="" media="" interface="">PHY 0 on miibus0
              rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
              re0: [FILTER]
              re1: <realtek 10="" 8139c+="" 100basetx="">port 0xd600-0xd6ff mem 0xefefb000-0xefefb1ff
              irq 5 at device 10.0 on pci2
              re1: Chip rev. 0x74800000
              re1: MAC rev. 0x00000000
              miibus1: <mii bus="">on re1
              rlphy1: <realtek internal="" media="" interface="">PHY 0 on miibus1
              rlphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
              re1: [FILTER]
              re2: <realtek 10="" 8139c+="" 100basetx="">port 0xd900-0xd9ff mem 0xefefc000-0xefefc1ff
              irq 11 at device 11.0 on pci2
              re2: Chip rev. 0x74800000
              re2: MAC rev. 0x00000000
              miibus2: <mii bus="">on re2
              rlphy2: <realtek internal="" media="" interface="">PHY 0 on miibus2
              rlphy2:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
              re2: [FILTER]
              re3: <realtek 10="" 8139c+="" 100basetx="">port 0xda00-0xdaff mem 0xefefd000-0xefefd1ff
              irq 12 at device 12.0 on pci2
              re3: Chip rev. 0x74800000
              re3: MAC rev. 0x00000000
              miibus3: <mii bus="">on re3
              rlphy3: <realtek internal="" media="" interface="">PHY 0 on miibus3
              rlphy3:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
              re3: [FILTER]
              re4: <realtek 10="" 8139c+="" 100basetx="">port 0xdd00-0xddff mem 0xefefe000-0xefefe1ff
              irq 9 at device 13.0 on pci2
              re4: Chip rev. 0x74800000
              re4: MAC rev. 0x00000000
              miibus4: <mii bus="">on re4
              rlphy4: <realtek internal="" media="" interface="">PHY 0 on miibus4
              rlphy4:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
              re4: [FILTER]
              re5: <realtek 10="" 8139c+="" 100basetx="">port 0xde00-0xdeff mem 0xefeff000-0xefeff1ff
              irq 6 at device 14.0 on pci2
              re5: Chip rev. 0x74800000
              re5: MAC rev. 0x00000000
              miibus5: <mii bus="">on re5
              rlphy5: <realtek internal="" media="" interface="">PHY 0 on miibus5
              rlphy5:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
              re5: [FILTER]
              isab0: <pci-isa bridge="">at device 31.0 on pci0
              isa0: <isa bus="">on isab0
              atapci0: <intel ich2="" udma100="" controller="">port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x37
              6,0xff00-0xff0f at device 31.1 on pci0
              ata0: <ata 0="" channel="">on atapci0
              ata0: [ITHREAD]
              ata1: <ata 1="" channel="">on atapci0
              ata1: [ITHREAD]
              cpu0 on motherboard
              unknown: <pnp0c01>can't assign resources (memory)
              atrtc0: <at realtime="" clock="">at port 0x70-0x71 irq 8 pnpid PNP0b00 on isa0
              uart0: <16550 or compatible> at port 0x3f8-0x3ff irq 4 flags 0x10 pnpid PNP0501
              on isa0
              uart0: [FILTER]
              uart0: console (9600,n,8,1)
              ppc0: <ecp parallel="" printer="" port="">at port 0x378-0x37f,0x778-0x77a irq 7 drq 3 pn
              pid PNP0401 on isa0
              ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
              ppc0: FIFO with 16/16/16 bytes threshold
              ppc0: [ITHREAD]
              ppbus0: <parallel port="" bus="">on ppc0
              ppi0: <parallel i="" o="">on ppbus0
              orm0: <isa option="" rom="">at iomem 0xe0000-0xe0fff pnpid ORM0000 on isa0
              unknown: <pnp0c01>can't assign resources (memory)
              RTC BIOS diagnostic error 20 <config_unit>Timecounter "TSC" frequency 1202731576 Hz quality 800
              Timecounters tick every 10.000 msec
              IPsec: Initialized Security Association Processing.
              ad0: 3871MB <cf 20070131="" 4gb="">at ata0-master PIO4
              Trying to mount root from ufs:/dev/ufs/pfsense0
              Configuring crash dumps…
              Mounting filesystems...
              Setting up embedded specific environment... done.

              ___
              / f
              / p _              / Sense
              _              / 
                  _              _/

              Welcome to pfSense 2.0.3-RELEASE  ...

              Creating symlinks......done.
              External config loader 1.0 is now starting... ad0s3
              Launching the init system... done.
              Initializing............................ done.
              Starting device manager (devd)...done.
              Loading configuration......done.
              Updating configuration...done.
              Cleaning backup cache.....done.
              Setting up extended sysctls...done.
              Setting timezone...done.
              Starting Secure Shell Services...done.
              Setting up polling defaure0: link state changed to DOWN
              lts...done.
              Setting up interfaces microcode...done.
              Configuring LAGG interfaces...done.
              Configuring VLAN interfaces...done.
              Configuring QinQ interfaces...done.
              Configuring WAN interface...re0: link state changed to UP
              done.
              Syncing OpenVPN settings...done.
              Starting syslog...done.
              pflog0: promiscuous mode enabled
              Configuring firewall......done.
              Starting PFLOG...done.
              Setting up gateway monitors...done.
              Synchronizing user settings...done.
              Starting webConfigurator...done.
              Configuring CRON...done.
              Starting NTP time client...Starting DNS forwarder...done.
              Configuring firewall......done.
              Generating RRD graphs...done.
              Starting CRON... done.
              Bootup complete</cf></config_unit></pnp0c01></isa></parallel></parallel></ecp></at></pnp0c01></ata></ata></intel></isa></pci-isa></realtek></mii></realtek></realtek></mii></realtek></realtek></mii></realtek></realtek></mii></realtek></realtek></mii></realtek></realtek></mii></realtek></pci></pcibios></pci></pci-pci></pci></pci></intel></software></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,sep,mtrr,pge,mca,cmov,pa<br></cf></config_unit></pnp0c01></isa></parallel></parallel></ecp></at></pnp0c01></ata></ata></intel></isa></pci-isa></realtek></mii></realtek></realtek></mii></realtek></realtek></mii></realtek></realtek></mii></realtek></realtek></mii></realtek></realtek></mii></realtek></pci></pcibios></pci></pci-pci></pci></pci></intel></software></fpu,vme,de,pse,tsc,msr,pae,mce,cx8,sep,mtrr,pge,mca,cmov,pa<br></cf></config_unit></pnp0c01></isa></parallel></parallel></ecp></at></pnp0c01></ata></ata></intel></isa></pci-isa></realtek>

              1 Reply Last reply Reply Quote 0
              • stephenw10S
                stephenw10 Netgate Administrator
                last edited by

                Ah, OK.
                So those logs show at least 3 boot sequences but only one time did you get the option to reassign the interfaces (due to a mismatch) and you never see the console menu.

                When it asks you to re-assign the interfaces this is what you should do. Instead of using the autodetect option just enter the interface names.
                I fired up my own X700 box:

                
Valid interfaces are:

re0   00:90:7f:2e:90:d2   (up) RealTek 8139C+ 10/100BaseTX
re1   00:90:7f:2e:90:d3 (down) RealTek 8139C+ 10/100BaseTX
re2   00:90:7f:2e:90:d4 (down) RealTek 8139C+ 10/100BaseTX
re3   00:90:7f:2e:90:d5 (down) RealTek 8139C+ 10/100BaseTX
re4   00:90:7f:2e:90:d6 (down) RealTek 8139C+ 10/100BaseTX
re5   00:90:7f:2e:90:d7 (down) RealTek 8139C+ 10/100BaseTX

Do you want to set up VLANs first?

If you are not going to use VLANs, or only for optional interfaces, you should
say no here and use the webConfigurator to configure VLANs later, if required.

Do you want to set up VLANs now [y|n]? n

*NOTE*  pfSense requires *AT LEAST* 1 assigned interface(s) to function.
        If you do not have *AT LEAST* 1 interfaces you CANNOT continue.

        If you do not have at least 1 *REAL* network interface card(s)
        or one interface with multiple VLANs then pfSense
        *WILL NOT* function correctly.

If you do not know the names of your interfaces, you may choose to use
auto-detection. In that case, disconnect all interfaces now before
hitting 'a' to initiate auto detection.

Enter the WAN interface name or 'a' for auto-detection: re0

Enter the LAN interface name or 'a' for auto-detection
NOTE: this enables full Firewalling/NAT mode.
(or nothing if finished): re1

Enter the Optional 1 interface name or 'a' for auto-detection
(or nothing if finished): re2

Enter the Optional 2 interface name or 'a' for auto-detection
(or nothing if finished):

The interfaces will be assigned as follows:

WAN  -> re0
LAN  -> re1
OPT1 -> re2

Do you want to proceed [y|n]?y

Writing configuration...done.
One moment while we reload the settings... done!
*** Welcome to pfSense 2.0.2-RELEASE-nanobsd (i386) on pfsense ***

  WAN (wan)                 -> re0        -> NONE (DHCP)
  LAN (lan)                 -> re1        -> NONE
  OPT1 (opt1)               -> re2        -> NONE

 0) Logout (SSH only)                  8) Shell
 1) Assign Interfaces                  9) pfTop
 2) Set interface(s) IP address       10) Filter Logs
 3) Reset webConfigurator password    11) Restart webConfigurator
 4) Reset to factory defaults         12) pfSense Developer Shell
 5) Reboot system                     13) Upgrade from console
 6) Halt system                       14) Disable Secure Shell (sshd)
 7) Ping host

                Once you have done that you should be able to access the webgui on re1, the LAN interface, which is the second port from the left on the X700 labelled '1'.

                Steve

                1 Reply Last reply Reply Quote 0
                • N
                  ninjamick
                  last edited by

                  so i assume the crossover cable goes in that port    and the router goes in the  external port

                  1 Reply Last reply Reply Quote 0
                  • stephenw10S
                    stephenw10 Netgate Administrator
                    last edited by

                    Yes.

                    Actually the sequence is slightly different from a factory reset:

                    
Valid interfaces are:

re0   00:90:7f:2e:90:d2   (up) RealTek 8139C+ 10/100BaseTX
re1   00:90:7f:2e:90:d3   (up) RealTek 8139C+ 10/100BaseTX
re2   00:90:7f:2e:90:d4   (up) RealTek 8139C+ 10/100BaseTX
re3   00:90:7f:2e:90:d5   (up) RealTek 8139C+ 10/100BaseTX
re4   00:90:7f:2e:90:d6   (up) RealTek 8139C+ 10/100BaseTX
re5   00:90:7f:2e:90:d7   (up) RealTek 8139C+ 10/100BaseTX

Do you want to set up VLANs first?

If you are not going to use VLANs, or only for optional interfaces, you should
say no here and use the webConfigurator to configure VLANs later, if required.

Do you want to set up VLANs now [y|n]? n

*NOTE*  pfSense requires *AT LEAST* 1 assigned interface(s) to function.
        If you do not have *AT LEAST* 1 interfaces you CANNOT continue.

        If you do not have at least 1 *REAL* network interface card(s)
        or one interface with multiple VLANs then pfSense
        *WILL NOT* function correctly.

If you do not know the names of your interfaces, you may choose to use
auto-detection. In that case, disconnect all interfaces now before
hitting 'a' to initiate auto detection.

Enter the WAN interface name or 'a' for auto-detection: re0

Enter the LAN interface name or 'a' for auto-detection
NOTE: this enables full Firewalling/NAT mode.
(or nothing if finished): re1

Enter the Optional 1 interface name or 'a' for auto-detection
(or nothing if finished): re2

Enter the Optional 2 interface name or 'a' for auto-detection
(or nothing if finished):

The interfaces will be assigned as follows:

WAN  -> re0
LAN  -> re1
OPT1 -> re2

Do you want to proceed [y|n]?y

Writing configuration........done.
Updating configuration...done.
Cleaning backup cache...done.
Setting up extended sysctls...done.
Setting timezone...done.
Starting Secure Shell Services...done.
Setting up polling defaults...done.
Setting up interfaces microcode...done.
Configuring LAGG interfaces...done.
Configuring VLAN interfaces...done.
Configuring QinQ interfaces...done.
Configuring WAN interface...done.
Configuring LAN interface...done.
Syncing OpenVPN settings...done.
Starting syslog...done.
Configuring firewall......done.
Starting PFLOG...done.
Setting up gateway monitors...done.
Synchronizing user settings...done.
Starting webConfigurator...done.
Configuring CRON...done.
Starting NTP time client...Starting DHCP service...done.
Starting DNS forwarder...done.
Configuring firewall......done.
Generating RRD graphs...done.
Starting CRON... done.
Bootup complete
(pfSense.localdomain) (console)

*** Welcome to pfSense 2.0.2-RELEASE-nanobsd (i386) on pfSense ***

  WAN (wan)                 -> re0        -> 192.168.111.15 (DHCP)
  LAN (lan)                 -> re1        -> 192.168.1.1
  OPT1 (opt1)               -> re2        -> NONE

 0) Logout (SSH only)                  8) Shell
 1) Assign Interfaces                  9) pfTop
 2) Set interface(s) IP address       10) Filter Logs
 3) Reset webConfigurator password    11) Restart webConfigurator
 4) Reset to factory defaults         12) pfSense Developer Shell
 5) Reboot system                     13) Upgrade from console
 6) Halt system                       14) Enable Secure Shell (sshd)
 7) Ping host

                    The only difference is that LAN is automatically assigned 192.168.1.1

                    Steve

                    1 Reply Last reply Reply Quote 0
                    • N
                      ninjamick
                      last edited by

                      thank you steve  still unable to get  webgui    dont know what the  heck is going on    get the green lights  ive  checked the  ip config  thats correct    as in  default gateway  192.168.1.1  but  still cant  webgui  ive tried  typing  192.168 in  internet explorer  adress bar  nothing  says problom    dont know what the hell im doing  wrong    think i  must admit defeat on this  go  to the basics    software  firewalls  for windows  :'(

                      1 Reply Last reply Reply Quote 0
                      • N
                        ninjamick
                        last edited by

                        well i got into  the webgui  however system froze  and i lost it  so start  again

                        1 Reply Last reply Reply Quote 0
                        • stephenw10S
                          stephenw10 Netgate Administrator
                          last edited by

                          Ooops! Any idea why?
                          Nearly there.  :)

                          Steve

                          1 Reply Last reply Reply Quote 0
                          • N
                            ninjamick
                            last edited by

                            no i dont know    focused more on getting pfsense working first    then i will sort out  bugs on system    what i refer to as the server  is just a storage machine  so  dont really  use it that much      but need pfsense on  wg x700  as i  store  everything on  there  wedding photos etc    and i use wireless access points  so i will have too  sort them out  after  too    infact i will have too  redo my entire network as i had a diffrent ip adress  so will have to reconfigure that after  but  thats not too much of a problom

                            1 Reply Last reply Reply Quote 0
                            • stephenw10S
                              stephenw10 Netgate Administrator
                              last edited by

                              I don't want to complicate things any further but you would probably be better connecting your main client machine to the LAN interface and the server to OPT1. It doesn't make much difference in the long term but initially the LAN firewall rules are relatively relaxed where as OPT1 will block everything.

                              Steve

                              1 Reply Last reply Reply Quote 0
                              • N
                                ninjamick
                                last edited by

                                yeah i know what  you mean  just i have another box  and another internet supply  for that machine  as i have  2 inertent supplys and  8  computers to link  up    too  2  watchguards  in my home  4 of the computers are  wireless  so that wont be too hard  just need to get the  main  2 sortted  and the firewalls

                                1 Reply Last reply Reply Quote 0
                                • stephenw10S
                                  stephenw10 Netgate Administrator
                                  last edited by

                                  Ok, following on from your PM, best to keep this on the forum where others can benefit or contribute.
                                  Yes you will need to change one of those subnets as they are conflicting. There is no point in trying anything else until you do because the conflict will cause meaningless results only confusing matters further.
                                  I suggest you change the pfSense LAN address rather than the modem because if you ever have to reset the modem it would re-create the conflict.

                                  At this point I am assuming you do not have access to the console menu via the X700 serial port. It is very useful to have that because you can always get back into the box that way if you accidentally lock yourself out of the webgui but it isn't necessary. To workaround the serial port quirk from the webgui do this:
                                  Go to Diagnostics: Command Prompt: and type in the Command: box

                                  echo 'console="comconsole"' >> /boot/loader.conf.local

                                  Click 'Execute' then type

                                  echo 'comconsole_speed="115200"' >> /boot/loader.conf.local

                                  Click 'Execute'.
                                  Reboot the X700 and change your serial terminal baud rate to 115200bps. You should now see the console menu.  :)

                                  As I say you don't have to do that but may help later.

                                  To change the LAN subnet in the webgui go to Interfaces: LAN:
                                  In the section marked 'Static IPv4 configuration' change the IP address to something other than 192.168.1.1/24. For example you could use 192.168.100.1/24. Leave everything else as is. Click 'save' but DO NOT click 'Apply changes'. As the message says you have to change the DHCP range to agree with your new LAN settings.
                                  Go to Services: DHCP Sever: LAN: (there may only be one tab at this point and LAN will be first anyway)
                                  Change the 'Range' fields so they are inside your new LAN subnet, so for example 192.168.100.10 to 192.168.100.50.
                                  Click 'save'.
                                  Go back to Interfaces: LAN: and click 'Apply changes'.

                                  You should now be able to connect on the new IP address once you have told your Windows box on LAN to request a new IP (or rebooted it). Sometimes with big changes like this it's necessary to reboot the pfSense box for the changes to fully apply so try that if it's not working.

                                  Now you can connect your modem and you should have internet access.

                                  Since your modem is using PPPoE you may be able to put it in bridge mode and use pfSense to connect directly. This removes any limitations the modem may be introducing and puts your public IP on the pfSense WAN interface. Who is the ISP(s)?

                                  Also since you have two DSL connections you could put both of them on the X700 and do load-balancing or fail-over. Just a thought for the future.  ;)

                                  Steve

                                  1 Reply Last reply Reply Quote 0
                                  • N
                                    ninjamick
                                    last edited by

                                    thank you for your reply i have  changed the  lan ip adress  however i see the  diagnostic icon  on the top  righthand side of the webgui  but i cant click on it      the same with  all them  only one i can click on is  system  thats it  very strange  indeed

                                    1 Reply Last reply Reply Quote 0
                                    • N
                                      ninjamick
                                      last edited by

                                      oooh i  forgot too mention the  isp provider is a company called  talktalk.net in the united kingdom

                                      1 Reply Last reply Reply Quote 0
                                      • stephenw10S
                                        stephenw10 Netgate Administrator
                                        last edited by

                                        Hmm, that is strange. The webgui uses javascript for the menus, they should appear beneath the titles when you mouse-over them, perhaps you have that disabled in your browser?

                                        I am familiar with TalkTalk. I've spent hours on hold waiting for their legendarily terribly customer support!  ::) Perhaps I was just unlucky.
                                        I take it you have their fibre option if you're using PPPoE? With the separate Openreach modem?

                                        Steve

                                        1 Reply Last reply Reply Quote 0
                                        • N
                                          ninjamick
                                          last edited by

                                          im on the 16mb  im using  talktalk  on  1 internet  but  100mb  on virgin  on the other  but  for the firebox im using 16mb  as thats just  for updating    thats all  and the tv    till my contract runs out  diabolical  customer service  and there level  2 techys couldnt solve a problom  if they  had the answers in front of them

                                          1 Reply Last reply Reply Quote 0
                                          • stephenw10S
                                            stephenw10 Netgate Administrator
                                            last edited by

                                            :D Perhaps I wasn't just unlucky then.

                                            So your Virgin connection is PPPoE?

                                            It doesn't matter at this point really. Just thinking ahead.

                                            Steve

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.