Upgrade screen never goes away without two reboots!
-
We may have to add a bit of logging to the package reinstall code.
It's not unusual for a package to fail for one reason or another, and pfSense takes the blame even though it's typically a problem with the package that causes it. :-)
-
@jimp: Yes, it is understandable. But what merits 2.1 is it's inclusion of tinc which is more robust than other VPN's for mesh networking.
With the tinc unstability plus the persistent upgrade screen for more than 24 hours makes it difficult to assess whether the upgrade is finished or not. It puts pfSense users in limbo, I am at the moment even after 24 hours. ;-) and in another machine for 12 hours with modsecurity installation (http://forum.pfsense.org/index.php/topic,63925.msg345954.html#msg345954)
Thanks for your reply.
-
The longest I've seen one go that actually succeeded was an hour and that was NanoBSD with squid and squidguard on an ALIX
If it has gone that long, check the console for errors. Reset the package lock and manually reinstall your packages.
-
@jimp, thanks for the alternative approach to go ahead with the upgrade. Mine is installed onto a HDD.
But even after locking package and reinstalling ModSecurity package, it halts forever (more than two hours) as I posted here: http://forum.pfsense.org/index.php/topic,63925.0.html.
In the system.log, there is a single line, that reads about this installation:
#clog /var/log/system.log | grep Apache
Jun 27 21:33:23 pfSense0 php: /pkg_mgr_install.php: Beginning package installation for Apache with mod_security-dev .
Jun 27 21:50:21 pfSense0 php: /pkg_mgr_install.php: Beginning package installation for Apache with mod_security-dev .
Jun 28 17:30:25 pfSense0 php: /pkg_mgr_install.php: Beginning package installation for Apache with mod_security-dev .
Jun 28 20:33:51 pfSense0 php: /pkg_mgr_install.php: Beginning package installation for Apache with mod_security-dev .I checked whether there is a resource shortage and it does not seem so:
last pid: 61373; load averages: 0.00, 0.00, 0.00 up 0+09:47:04 20:39:17
65 processes: 1 running, 64 sleeping
CPU: 0.0% user, 0.0% nice, 0.0% system, 0.0% interrupt, 100% idle
Mem: 268M Active, 819M Inact, 159M Wired, 31M Cache, 112M Buf, 203M Free
Swap: 4096M Total, 4096M FreeThis is obvious that I tried four times since yesterday to install and in a gap of three hours today becuase it halted. How can I overcome these?
-
You must get to the console and see what is displayed there when it attempts to reinstall. And then try to get the attention of the package maintainer so they can fix it.
-
I executed 'tail -f /var/log/syslog.log' which showed the same line as I have stated. Thereafter I executed 'clog /var/log/system.log | grep Apache' to give a sense how long tbe inslallation freezes.
I have been trying with two pacakges (one is tinc) and both of them are troublesome! ;-)
-
No I mean the actual physical console: VGA or serial.
That's where the output is, not a log.
-
I did just add some more logging to the package reinstall process though, but it can only do so much.
https://github.com/pfsense/pfsense/commit/2b125a17e91b5b63694de0c272e5f4fd154598da
The bulk of the output only goes to the console and can't go anywhere else.
-
No I mean the actual physical console: VGA or serial.
That's where the output is, not a log.
Yes I am on a vga console.
-
Then press Scroll Lock immediate after the update, and page up a few times to see what failed.
Usually it will be stuck there in the package reinstall and never drops you to the menu.
-
There is no error reports in relation to the ModSecurity package except the line quoted above. It downloads the packages and xml files and finally halts at;
"Executing custom_php_resync_config_command()…"
