Netgate Discussion Forum
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Search
    • Register
    • Login

    WiFi Question

    Scheduled Pinned Locked Moved Wireless
    15 Posts 4 Posters 9.2k Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • K
      kejianshi
      last edited by

      I prefer using ethernet > wireless AP / Client, but if your problem is that your wireless card is being shown as WAN rather than LAN or OPT(#) or something, just go into your assign interfaces menu and assign it to whatever you like.  Now, here is the thing.  I think its going to want its own subnet just like any NIC card would unless you bridge it to your LAN interface.  Its an aweful lot of fuss to have wireless in the box rather than outside it.

      But…  This might get you going right direction if you just MUST use wireless inside pfsense.

      http://doc.pfsense.org/smiller/add_wifi_interface/Add_WiFi_Interface.htm

      1 Reply Last reply Reply Quote 0
      • W
        wallabybob
        last edited by

        @t_enriquez:

        I could not figure out how connect the pfsense wifi card to the existing AP.  iwn0 is setup as the WAN interface.

        I presume you mean configure rather than connect.
        On the Interfaces -> WAN page in the Network-specific wireless configuration set the Mode to Infrastructure (to connect to an existing AP), set the SSID to the WiFi network name configured in the AP and set the encryption parameters (if used) to match what is set in the AP (encryption mode, password etc).

        The General Configuration parameters should be set the same as you would set for a wired interface.

        1 Reply Last reply Reply Quote 0
        • W
          wallabybob
          last edited by

          @kejianshi:

          if your problem is that your wireless card is being shown as WAN

          My reading of the original post is that is what is required as a temporary replacement for a damaged wired link. I suspect this is a "get something working quickly with what is already available" problem rather than a "what is the optimum way of putting a WiFi access point on a network with pfSense present" question.

          1 Reply Last reply Reply Quote 0
          • K
            kejianshi
            last edited by

            I think you are probably correct.

            1 Reply Last reply Reply Quote 0
            • T
              t_enriquez
              last edited by

              That is correct.  This is a temp solution with already available resources.

              1 Reply Last reply Reply Quote 0
              • T
                t_enriquez
                last edited by

                Thanks for all of the replies.  I finally have the WiFi "configured" correctly.  I tried to "bridge" the two interfaces and it looks like my WiFi adapter will not work.

                I'll have to make a few changes to the devices to use the WiFi through the pfsense box.

                FYI, the computer is a Foxconn nT-i1200-0H0WBNA.

                Thanks again for the replies

                1 Reply Last reply Reply Quote 0
                • T
                  t_enriquez
                  last edited by

                  @t_enriquez:

                  Thanks for all of the replies.  I finally have the WiFi "configured" correctly.  I tried to "bridge" the two interfaces and it looks like my WiFi adapter will not work.

                  I'll have to make a few changes to the devices to use the WiFi through the pfsense box.

                  FYI, the computer is a Foxconn nT-i1200-0H0WBNA.

                  Thanks again for the replies

                  The error when trying to create the bridge was:

                  The following input errors were detected:

                  Bridging a wireless interface is only possible in hostap mode.

                  1 Reply Last reply Reply Quote 0
                  • W
                    wallabybob
                    last edited by

                    @t_enriquez:

                    The error when trying to create the bridge was:

                    The following input errors were detected:

                    Bridging a wireless interface is only possible in hostap mode.

                    I don't know the reason for that restriction. Why do you need to bridge?

                    1 Reply Last reply Reply Quote 0
                    • stan-qazS
                      stan-qaz
                      last edited by

                      I'd really lean to external wireless extenders.

                      Cheap $60, not so fast: http://www.newegg.com/Product/Product.aspx?Item=N82E16833127294

                      More $120 pretty fast: http://www.newegg.com/Product/Product.aspx?Item=9SIA0SF0BV4130

                      I use a 1525 in bridge mode to get my Ethernet to a printer and a backup drive sitting in a spot that it would be hard to get cables to. It runs for months on end with no hassles and recovers from power outages with no problems. Other brands might work better but I got the DAP really cheap.

                      1 Reply Last reply Reply Quote 0
                      • T
                        t_enriquez
                        last edited by

                        @wallabybob:

                        @t_enriquez:

                        The error when trying to create the bridge was:

                        The following input errors were detected:

                        Bridging a wireless interface is only possible in hostap mode.

                        I don't know the reason for that restriction. Why do you need to bridge?

                        I need to bridge to keep the lan segment the same on both sides.

                        1 Reply Last reply Reply Quote 0
                        • T
                          t_enriquez
                          last edited by

                          @stan-qaz:

                          I'd really lean to external wireless extenders.

                          Cheap $60, not so fast: http://www.newegg.com/Product/Product.aspx?Item=N82E16833127294

                          More $120 pretty fast: http://www.newegg.com/Product/Product.aspx?Item=9SIA0SF0BV4130

                          I use a 1525 in bridge mode to get my Ethernet to a printer and a backup drive sitting in a spot that it would be hard to get cables to. It runs for months on end with no hassles and recovers from power outages with no problems. Other brands might work better but I got the DAP really cheap.

                          Thanks for the reply.  I'll check them out if we can't run the new cable right away.

                          1 Reply Last reply Reply Quote 0
                          • First post
                            Last post
                          Copyright 2025 Rubicon Communications LLC (Netgate). All rights reserved.